Valve Body Overview
WARNING: This page does not describe the selected car, but rather 8 other vehicles, including the 2010 Volkswagen Jetta, 2009 Volkswagen Jetta, 2009 Volkswagen Golf, 2008 Volkswagen Jetta, and 2008 Volkswagen Golf. However, it is still accessible from the selected car via links, so may be relevant.
WARNING:
Do not run the engine or tow the vehicle when the transmission fluid pan is removed or when there is no Automatic Transmission Fluid (ATF) in the engine.
- The valve body and the wiring harnesses can also be removed with the transmission installed.
- Install the O-rings using ATF. Other types of lubricants lead to faults in the transmission hydraulics.
- Always replace a dirty or faulty valve body.
- Only use lint free cloths
- Check the ATF level after installing the transmission fluid pan. Refer to ATF LEVEL, CHECKING AND FILLING .
- Inspection Plug
- Automatic Transmission Fluid (ATF) level, checking and filling, refer to ATF LEVEL, CHECKING AND FILLING .
- Tightening specification, refer to FASTENER TIGHTENING SPECIFICATIONS .
- Seal
- Always replace.
- Overflow Pipe
- Remove in order to drain the ATF.
- Tightening specification, refer to FASTENER TIGHTENING SPECIFICATIONS .
- Transmission Fluid Pan
- Removing and installing, refer to TRANSMISSION FLUID PAN .
- Bolt
- Tighten the ATF pan bolts diagonally and in several steps.
- Tightening specification, refer to FASTENER TIGHTENING SPECIFICATIONS .
- Seal
- With spacers (quantity: 8).
- Check before installing.
- Replace brittle, cracked or deformed seals.
- Magnet
- Quantity: 2; in the depressions in the ATF pan.
- Clean before installing the pan.
- Bolt
- For attaching the valve body to the transmission.
- Quantity 12; with different lengths, refer to LOOSEN THE VALVE BODY BOLTS -ARROWS-, -ARROWS A- AND -ARROWS B- DIAGONALLY AND THEN REMOVE THE VALVE BODY .
- Always replace the bolts.
- Tightening specification, refer to FASTENER TIGHTENING SPECIFICATIONS .
- Bolt
- Quantity: 3
- For attaching the ATF filter to the valve body.
- Tightening specification, refer to FASTENER TIGHTENING SPECIFICATIONS .
- Oil Filter
- Removing and installing, refer to TRANSMISSION FLUID FILTER .
- Valve Body
- Removing and installing, refer to VALVE BODY .
- For the correct solenoid valve designation, refer to SOLENOID VALVE DESIGNATION .
- Bolt
- Tightening specification, refer to FASTENER TIGHTENING SPECIFICATIONS .
- Bolt
- Tightening specification, refer to FASTENER TIGHTENING SPECIFICATIONS .
- Transmission Input Speed Sensor -G182-
- Removing and installing, refer to TRANSMISSION INPUT SPEED SENSOR .
- Bolt
- Tightening specification, refer to FASTENER TIGHTENING SPECIFICATIONS .
- Transmission Output Speed Sensor -G195-
- Removing and installing, refer to Transmission Output Speed Sensor -G195- .
- Transmission Housing
- Illustrated here without the ATF cooler.
- Vent
- Multifunction Transmission Range Switch -F125-
- Removing and installing, refer to MULTIFUNCTION TRANSMISSION RANGE SWITCH -F125- .
- Adjusting, refer to ADJUSTING .
- Transmission Fluid Temperature Sensor -G93-
- Integrated inside the wiring harness -item 23-.
- Bolt
- Tightening specification, refer to FASTENER TIGHTENING SPECIFICATIONS .
- Bolt
- Tightening specification, refer to FASTENER TIGHTENING SPECIFICATIONS .
- Wiring Harness with 8 Pin Connector
- With an O-ring on the connector; always replace the O-ring.
- With the transmission fluid temperature sensor.
- For the transmission input speed sensor.
- For the transmission output speed sensor.
- Sensor installed location, refer to SENSOR DESIGNATION .
- Removing and installing, refer to WIRING HARNESS WITH 8 PIN CONNECTOR .
- Seal
- Always replace
- Plug
- Tightening specification, refer to FASTENER TIGHTENING SPECIFICATIONS .
- Shift Lever
- For the shift shaft.
- Removing and installing, refer to VALVE BODY .
- Washer
- Nut
- Installed position: The centering collar faces the washer -item 27-.
- Tightening specification, refer to FASTENER TIGHTENING SPECIFICATIONS .
- Spring
- Piston
- Wiring Harness with 14 Pin Connector
- For the solenoid valve.
- With an O-ring on the connector; always replace the O-ring.
- Solenoid valve installed location and wiring harness routing, refer to SOLENOID VALVE DESIGNATION .
- Removing and installing, refer to WIRING HARNESS WITH 14 PIN CONNECTOR .
- Bolt
- Tightening specification, refer to FASTENER TIGHTENING SPECIFICATIONS .