LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2024 >> Corolla LE >> Repair and Diagnosis >> External Pages >> Different car >> Section 364 (Automatic Transaxle System (K313) - Diagnostic Codes & Circuit Tests) >> Continuously Variable Transaxle System >> DTC P1586: Acceleration Sensor Malfunction [01/2019 - 11/2022] >> Procedure

DTC P1586: Acceleration Sensor Malfunction [01/2019 - 11/2022]: Procedure

WARNING: This page is about a different car, the 2022 Toyota Corolla, 2021 Toyota Corolla, 2020 Toyota Corolla, and 2019 Toyota Corolla. However, it is still accessible from the selected car via links, so may be relevant.
  1. CHECK DTC OUTPUT 
    1. Connect the Techstream to the DLC3.
    2. Turn the ignition switch to ON.
    3. Turn the Techstream on.
    4. Check for DTCs.

      Powertrain > Engine and ECT > Trouble Codes 

      Result

      Result Proceed to
      DTC U0129 is not output A
      DTC U0129 is output B

    Result: 

    B 

    GO TO CAN COMMUNICATION SYSTEM. Refer to  DIAGNOSIS SYSTEM [01/2019 - 03/2019]  , or refer to  DIAGNOSIS SYSTEM [03/2019 - 09/2019]  , or refer to  DIAGNOSIS SYSTEM [09/2019 - 04/2020]  , or refer to  DIAGNOSIS SYSTEM [04/2020 - 09/2022]  , or refer to  DIAGNOSIS SYSTEM [09/2022 - 11/2022] 

    Result: 

    A 

    See step  2

  2. CHECK DTC OUTPUT (IN ADDITION TO DTC P1586) 
    1. Connect the Techstream to the DLC3.
    2. Turn the Techstream on.
    3. Turn the ignition switch to ON.
    4. Clear the DTCs.

      Powertrain > Engine and ECT > Clear DTCs 

    5. Perform a road test where the vehicle is driven at 30 km/h (19 mph) or more, the brakes are applied at least 16 times and the vehicle is finally stopped.
    6. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

      Powertrain > Engine and ECT > Trouble Codes 

    7. Read the DTCs using the Techstream.

      HINT: 

      If any DTCs other than P1586 are output, perform troubleshooting for those DTCs first.

      Result

      Result Proceed to
      Only DTC P1586 is output A
      DTC P1586 and other DTCs are output B

    Result: 

    B 

    GO TO DTC CHART. Refer to  DIAGNOSTIC TROUBLE CODE CHART [01/2019 - 03/2019]  , or refer to  DIAGNOSTIC TROUBLE CODE CHART [03/2019 - 11/2022] 

    Result: 

    A 

    See step  3

  3. READ VALUE USING TECHSTREAM (G SENSOR) 
    1. Connect the Techstream to the DLC3.
    2. Turn the ignition switch to ON.
    3. Turn the Techstream on.
    4. Enter the following menus: Powertrain / Engine and ECT / Data List.
    5. According to the display on the Techstream, read the Data List.

      Powertrain > Engine and ECT > Data List 

      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      G Sensor Converted output voltage of yaw rate and acceleration sensor Min.: 0 V
      Max.: 79.998 V
      • 2.31 to 2.69 V: Vehicle on level ground
      • 1.88 to 2.5 V: Decelerating
      • 2.5 to 3.11 V: Accelerating
      • Stuck at 1.87 V: G sensor malfunction
      • Stuck at 1.87 V: Communication malfunction
      		 -

      Powertrain > Engine and ECT > Data List 

      Tester Display
      G Sensor

      Result

      Result Proceed to
      Data List value is not normal A
      Data List value is normal B

    Result: 

    B 

    REPLACE BRAKE ACTUATOR ASSEMBLY. Refer to  COMPONENTS [01/2019 - 09/2022]  , or refer to  COMPONENTS [09/2022 - ] 

    Result: 

    A 

    See step  4

  4. REPLACE AIRBAG SENSOR ASSEMBLY 
    1. Replace the airbag sensor assembly.

      Refer to COMPONENTS [06/2018 - 09/2022] , or refer to COMPONENTS [09/2022 - 11/2022]

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    PERFORM INITIALIZATION. Refer to  INITIALIZATION [01/2019 - 11/2022] 

scientia non olet · About LEMON Manuals