LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2021 >> 4Runner TRD Pro >> Repair and Diagnosis >> Electrical >> Gauges >> Interior Panels / Trim - Service Information >> Instrument Panel Safety Pad >> Installation [08/2022 - ] >> Procedure

Installation [08/2022 - ]: Procedure

  1. INSTALL INSTRUMENT PANEL SUB-ASSEMBLY 
    1. Attach the 2 guides to install the instrument panel sub-assembly.
    2. Connect each connector and attach the clamps and claws.
    3. Install the 2 passenger airbag bolts.

      Torque: 20 N.m (204 kgf/cm, 15 ft.lbf) 

    4. Install the bolt labeled A.

      Torque: 8.0 N.m (82 kgf/cm, 71 in.lbf) 

    5. Install the 6 bolts <E> and nut <F>.
      GTY897164Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      TEXT IN ILLUSTRATION

      *1 Bolt <E> *2 Nut <F>
      *3 Guide *4 Passenger Airbag Bolt
      *5 Bolt A - -
  2. INSTALL 4 WHEEL DRIVE CONTROL ECU NO. 2 (for 4WD) 
    1. for VF2A:

      Install the 4 wheel drive control ECU No. 2.

      Refer to PROCEDURE - Step 1

    2. for VF2CM:

      Install the 4 wheel drive control ECU No. 2.

      Refer to PROCEDURE - Step 1

    3. for VF4BM:

      Install the 4 wheel drive control ECU No. 2.

      Refer to PROCEDURE - Step 1

  3. INSTALL TELEMATICS TRANSCEIVER 

    Refer to PROCEDURE - Step 3

  4. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY 

    Refer to PROCEDURE - Step 2

  5. INSTALL NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY 
    1. Attach the 2 clips, 4 claws and 3 guides to install the No. 1 instrument panel speaker panel sub-assembly.
  6. INSTALL NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY 
    1. Attach the 2 clips, 3 claws and 3 guides to install the No. 2 instrument panel speaker panel sub-assembly.
  7. INSTALL NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY 
    1. Attach the 4 clips and 2 guides to install the No. 1 instrument panel register assembly.
  8. INSTALL NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY 

    HINT: 

    Use the same procedure as for the No. 1 instrument panel register assembly.

  9. INSTALL LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/o Climate Control Seat System) 
    1. Connect 2 connectors.
    2. Attach the 4 clips to install the lower center instrument cluster finish panel sub-assembly.
    3. Install the 2 screws <B>.
  10. INSTALL LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/ Climate Control Seat System) 
    1. Connect 3 connectors.
    2. Attach the 4 clips to install the lower center instrument cluster finish panel sub-assembly.
    3. Install the 2 screws <B>.
  11. INSTALL RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKETS 
  12. INSTALL HEATER CONTROL ASSEMBLY 

    Refer to PROCEDURE - Step 1

  13. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY 
    1. Connect each connector.
    2. Attach the 10 clips and guide to install the lower instrument panel sub-assembly.
    3. Install the 3 screws <B> and 2 bolts <C>.
  14. INSTALL INSTRUMENT PANEL BOX DOOR COVER 
    1. Attach the 2 claws and 2 guides to install the instrument panel box door cover.

      HINT: 

      Use the same procedure for all the instrument panel box door covers.

  15. INSTALL LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY 

    Refer to PROCEDURE - Step 1

  16. INSTALL LOWER INSTRUMENT COVER LH 
    1. Attach the 4 claws to install the lower instrument cover LH.
  17. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY 
    1. Attach the 3 clips and 2 guides to install the No. 2 instrument panel under cover sub-assembly.
  18. INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY 

    Refer to PROCEDURE - Step 1

  19. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY 
    1. Connect each connector and hood lock control cable assembly.
    2. Attach the 13 clips and 2 guides to install the lower instrument panel finish panel sub-assembly.
    3. Install the 2 bolts <C>.
    4. Attach the 2 claws to close the cover.
  20. INSTALL COMBINATION METER ASSEMBLY 

    Refer to PROCEDURE - Step 1

  21. INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY 
    1. Attach the 7 clips to install the instrument cluster finish panel sub-assembly.
  22. INSTALL NO. 2 SWITCH HOLE BASE 
    1. Connect each connector.
    2. Attach the 6 clips and 2 guides to install the No. 2 switch hole base.
  23. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY 
    1. Connect each connector and cooler thermistor.
    2. Attach the 4 clips to install the lower instrument panel finish panel assembly.
  24. INSTALL FRONT PILLAR GARNISH LH 

    See step  70

  25. INSTALL FRONT PILLAR GARNISH RH 

    See step  71

  26. INSTALL NO. 1 ASSIST GRIP 

    See step  72

  27. INSTALL ASSIST GRIP PLUG 

    See step  73

  28. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH 

    See step  74

  29. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH 

    HINT: 

    Use the same procedure as for the LH side.

  30. INSTALL COWL SIDE TRIM BOARD LH 

    See step  76

  31. INSTALL COWL SIDE TRIM BOARD RH 

    HINT: 

    Use the same procedure as for the LH side.

  32. INSTALL DOOR SCUFF PLATE ASSEMBLY LH 

    See step  78

  33. INSTALL DOOR SCUFF PLATE ASSEMBLY RH 

    HINT: 

    Use the same procedure as for the LH side.

  34. INSTALL REAR CONSOLE BOX ASSEMBLY 

    Refer to INSTALLATION [08/2019 - ] 

  35. INSTALL HEADLIGHT DIMMER SWITCH ASSEMBLY 

    Refer to INSTALLATION [08/2015 - ]

  36. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL 
    NOTE:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Refer to INITIALIZATION [08/2022 - ]

  37. CHECK SRS WARNING LIGHT 

    Refer to DIAGNOSIS SYSTEM [08/2019 - ]

scientia non olet · About LEMON Manuals