LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2017 >> Highlander XLE, FWD >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 109 (Engine Control System (2GR-FXS) - Service Information - (Hybrid)) >> Camshaft Oil Control Solenoid >> Installation [11/2016 - ] >> Procedure

Installation [11/2016 - ]: Procedure

WARNING: This page is about a different variant/trim than selected.
  1. INSTALL CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Exhaust Side of Bank 1) 
    1. Apply engine oil to a new O-ring and install it to the camshaft timing oil control solenoid assembly as shown in the illustration.
      GTY706621Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 O-ring
      NOTE:

      Do not damage the O-ring.

    2. Apply adhesive to 2 or 3 threads of 2 new bolts.
      GTY631072Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Adhesive

      Adhesive

      Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

    3. Install the camshaft timing oil control solenoid assembly to the timing chain cover assembly with the 2 bolts.

      Torque: 10 N*m (102 kgf*cm, 7 ft.*lbf) 

      NOTE:
      • If the camshaft timing oil control solenoid assembly has been struck or dropped, replace it.
      • Make sure that the O-ring is not cracked or moved out of place when installing the camshaft timing oil control solenoid assembly.
    4. Connect the camshaft timing oil control solenoid assembly connector.
  2. INSTALL CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Intake Side of Bank 1) 
    1. Apply engine oil to a new O-ring and install it to the camshaft timing oil control solenoid assembly as shown in the illustration.
      GTY706621Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 O-ring
      NOTE:

      Do not damage the O-ring.

    2. Apply adhesive to 2 or 3 threads of 2 new bolts.
      GTY631072Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Adhesive

      Adhesive

      Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

    3. Temporarily install the camshaft timing oil control solenoid assembly to the timing chain cover assembly with the 2 bolts.
      NOTE:
      • If the camshaft timing oil control solenoid assembly has been struck or dropped, replace it.
      • Make sure that the O-ring is not cracked or moved out of place when installing the camshaft timing oil control solenoid assembly.
    4. Using SST, tighten the 2 bolts.
      • SST: 09961-00950 

      Specified tightening torque 

      Torque: 10 N*m (102 kgf*cm, 7 ft.*lbf) 

      HINT: 

      • Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

        Refer to PRECAUTION [11/2016 - ]

      • When using SST (fulcrum length of 150 mm (5.91 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

        5.2 N*m (53 kgf*cm, 46 in.*lbf)

      GTY698042Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Torque Wrench Fulcrum Length
    5. Connect the camshaft timing oil control solenoid assembly connector.
  3. INSTALL FRONT NO. 1 ENGINE MOUNTING BRACKET LH 

    Refer to PROCEDURE - Step 4

  4. CONNECT ENGINE WIRE 

    Refer to PROCEDURE - Step 5

  5. INSTALL CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Intake Side of Bank 2) 
    1. Apply engine oil to a new O-ring and install it to the camshaft timing oil control solenoid assembly as shown in the illustration.
      GTY706621Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 O-ring
      NOTE:

      Do not damage the O-ring.

    2. Apply adhesive to 2 or 3 threads of 2 new bolts.
      GTY631072Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Adhesive

      Adhesive

      Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

    3. Install the camshaft timing oil control solenoid assembly to the timing chain cover assembly with the 2 bolts.

      Torque: 10 N*m (102 kgf*cm, 7 ft.*lbf) 

      NOTE:
      • If the camshaft timing oil control solenoid assembly has been struck or dropped, replace it.
      • Make sure that the O-ring is not cracked or moved out of place when installing the camshaft timing oil control solenoid assembly.
    4. Connect the camshaft timing oil control solenoid assembly connector.
  6. INSTALL ENGINE MOVING CONTROL ROD BRACKET 

    Refer to PROCEDURE - Step 39

  7. INSTALL NO. 2 ENGINE MOUNTING STAY RH 

    Refer to PROCEDURE - Step 10

  8. INSTALL RESERVOIR BRACKET 

    Refer to PROCEDURE - Step 41

  9. INSTALL BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY 

    Refer to PROCEDURE - Step 42

  10. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 10

  11. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY 

    Refer to INSTALLATION [02/2014 - ]

  12. INSTALL CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Exhaust Side of Bank 2) 
    1. Apply engine oil to a new O-ring and install it to the camshaft timing oil control solenoid assembly as shown in the illustration.
      GTY706621Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 O-ring
      NOTE:

      Do not damage the O-ring.

    2. Apply adhesive to 2 or 3 threads of 2 new bolts.
      GTY631072Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Adhesive

      Adhesive

      Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

    3. Using a 10 mm deep socket wrench, install the camshaft timing oil control solenoid assembly to the timing chain cover assembly with the 2 bolts.

      Torque: 10 N*m (102 kgf*cm, 7 ft.*lbf) 

      NOTE:
      • If the camshaft timing oil control solenoid assembly has been struck or dropped, replace it.
      • Make sure that the O-ring is not cracked or moved out of place when installing the camshaft timing oil control solenoid assembly.
    4. Connect the camshaft timing oil control solenoid assembly connector.
  13. INSTALL ECM 

    See step  4

  14. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL 

    Refer to PROCEDURE - Step 4

  15. INSTALL NO. 3 DECK BOARD SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 70

  16. INSTALL DECK BOARD ASSEMBLY 

    Refer to PROCEDURE - Step 71

  17. INSPECT FOR ENGINE OIL LEAK 

    Refer to PROCEDURE - Step 5

  18. INSTALL V-BANK COVER SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 74

scientia non olet · About LEMON Manuals