Front Suspension Member: Installation

INSTALL FRONT SUSPENSION MEMBER BODY MOUNTING REAR CUSHION LH
1. Temporarily install a new front suspension member body mounting rear cushion LH while confirming the installation direction.
  NOTE: Position the front suspension member body mounting rear cushion in the correct direction.
  
  Fig 1: Identifying Front Suspension Member Body Mounting Rear Cushion LH
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Install SST as shown in the illustration.
  SST 09830-10010 (09830-01010, 09830-01020, 09830-01030, 09830-01060)
  
  Fig 2: Identifying Front Suspension Member Body Mounting Rear Cushion
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Using SST, install the front suspension member body mounting rear cushion LH as shown in the illustration.
  NOTE: Check that there is no clearance between the front suspension member and the front suspension member body mounting rear cushion LH.
  
  Fig 3: Installing Front Suspension Member Body Mounting Rear Cushion LH
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL FRONT SUSPENSION MEMBER BODY MOUNTING REAR CUSHION RH
1. Temporarily install a new front suspension member body mounting rear cushion RH while confirming the installation direction.
  NOTE: Position the front suspension member body mounting rear cushion in the correct direction.
  
  Fig 4: Identifying Front Suspension Member Body Mounting Rear Cushion RH
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Using SST, install the front suspension member body mounting rear cushion RH.
  SST 09830-10010 (09830-01010, 09830-01020, 09830-01030, 09830-01060)
  
  HINT:
  
  Perform the same procedure as the LH side.
INSTALL FRONT SUSPENSION MEMBER BODY MOUNTING FRONT CUSHION
1. Temporarily install a new front suspension member body mounting front cushion while confirming the installation direction.
  NOTE: Position the front suspension member body mounting front cushion in the correct direction.
  
  Fig 5: Identifying Front Suspension Member Body Mounting Front Cushion
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Using SST, install the front suspension member body mounting front cushion as shown in the illustration.
  SST 09830-10010 (09830-01010, 09830-01020, 09830-01030, 09830-01060)
  
  NOTE: Check that there is no clearance between the front suspension member and the front suspension member body mounting rear cushion.
INSTALL FRONT SUSPENSION MEMBER BODY MOUNTING REAR STOPPER
INSTALL FRONT SUSPENSION MEMBER BODY MOUNTING FRONT STOPPER

Fig 6: Installing Front Suspension Member Body Mounting Front Cushion
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL FRONT SUSPENSION MEMBER DYNAMIC DAMPER
1. Install the front suspension member dynamic damper with the 2 bolts.
  Torque: 29 N*m (296 kgf*cm, 21 ft.*lbf)
INSTALL FRONT LOWER SUSPENSION ARM LH (See REMOVAL )
INSTALL FRONT LOWER SUSPENSION ARM RH
HINT:

Perform the same procedure as the LH side.

Fig 7: Locating Front Suspension Member Dynamic Damper Bolts
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL TRANSVERSE ENGINE MOUNTING INSULATOR (for 2GR-FE) (See INSTALLATION )
INSTALL FRONT FRAME ASSEMBLY (for 2GR-FE) (See INSTALLATION )
INSTALL FRONT FRAME ASSEMBLY (for 1AR-FE) (See INSTALLATION )
REMOVE ENGINE HANGERS (for 2GR-FE) (See INSTALLATION )
REMOVE ENGINE HANGER NO.1 (for 1AR-FE)
INSTALL POWER STEERING LINK ASSEMBLY (See INSTALLATION )
INSTALL FRONT STABILIZER BAR WITH FRONT STABILIZER LINK ASSEMBLY
INSTALL NO. 1 FRONT STABILIZER BRACKET LH (See INSTALLATION )
INSTALL NO. 1 FRONT STABILIZER BRACKET RH
HINT:

Perform the same procedure as the LH side.
INSTALL ENGINE ASSEMBLY WITH TRANSAXLE
HINT:
- Refer to the procedure from Install Engine Assembly with Transaxle (for 2GR-FE) (See INSTALLATION ).
- Refer to the procedure from Install Engine Assembly with Transaxle (for 1AR-FE) (See INSTALLATION ).