LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2009 >> Corolla S, 1.8 L, Standard >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 3 (Engine Lubrication System (2AZ-FE)) >> Oil Pump >> Removal

Oil Pump: Removal

WARNING: This page is about a different variant/trim than selected.
  1. DISCHARGE FUEL SYSTEM PRESSURE  (See REMOVAL )
  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 
  3. REMOVE FRONT WIPER ARM HEAD CAP  (See ON-VEHICLE INSPECTION )
  4. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH  (See ON-VEHICLE INSPECTION )
  5. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH  (See REMOVAL )
  6. REMOVE HOOD TO COWL TOP SEAL  (See REMOVAL )
  7. REMOVE CENTER NO. 1 COWL TOP VENTILATOR LOUVER  (See REMOVAL )
  8. REMOVE COWL TOP VENTILATOR LOUVER LH  (See REMOVAL )
  9. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY  (See REMOVAL )
  10. REMOVE OUTER COWL TOP PANEL  (See REMOVAL )
  11. REMOVE SUSPENSION TOWER DAMPER ASSEMBLY (w/ Front Strut Bar)  (See REMOVAL )
  12. REMOVE FRONT WHEEL RH 
  13. REMOVE ENGINE UNDER COVER LH 
  14. REMOVE ENGINE UNDER COVER RH 
  15. REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY  (See REMOVAL )
  16. DRAIN ENGINE COOLANT  (See COOLANT )
  17. DRAIN ENGINE OIL  (See REPLACEMENT )
  18. REMOVE CENTER EXHAUST PIPE ASSEMBLY  (See REMOVAL )
  19. REMOVE FRONT EXHAUST PIPE ASSEMBLY  (See REMOVAL )
  20. REMOVE V-RIBBED BELT  (See ON-VEHICLE INSPECTION )
  21. REMOVE GENERATOR ASSEMBLY  (See REMOVAL )
  22. DISCONNECT NO. 1 RADIATOR HOSE  (See REMOVAL )
  23. DISCONNECT OUTLET HEATER WATER HOSE  (See REMOVAL )
  24. DISCONNECT INLET HEATER WATER HOSE  (See REMOVAL )
  25. SEPARATE RADIATOR RESERVE TANK ASSEMBLY  (See REMOVAL )
  26. REMOVE AIR CLEANER CAP SUB-ASSEMBLY WITH HOSE  (See ON-VEHICLE INSPECTION )
  27. REMOVE THROTTLE BODY ASSEMBLY  (See REMOVAL )
  28. REMOVE IGNITION COIL ASSEMBLY  (See REMOVAL )
  29. REMOVE SPARK PLUG  (See REMOVAL )
  30. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY  (See REMOVAL )
  31. REMOVE ENGINE OIL LEVEL DIPSTICK 
  32. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE  (See REMOVAL )
  33. REMOVE FUEL MAIN TUBE  (See REMOVAL )
  34. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY  (See REMOVAL )
  35. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY  (See REMOVAL )
  36. REMOVE INTAKE MANIFOLD  (See INSTALLATION )
  37. REMOVE NO. 1 INTAKE MANIFOLD INSULATOR  (See REMOVAL )
  38. REMOVE MANIFOLD STAY  (See REMOVAL )
  39. REMOVE NO. 2 MANIFOLD STAY  (See REMOVAL )
  40. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR  (See REMOVAL )
  41. REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY  (See REMOVAL )
  42. REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH  (See REMOVAL )
  43. REMOVE IDLER PULLEY SUB-ASSEMBLY  (See REMOVAL )
  44. REMOVE OIL PAN SUB-ASSEMBLY  (See REMOVAL )
  45. SET NO. 1 CYLINDER TO TDC / COMPRESSION  (See REMOVAL )
  46. REMOVE CRANKSHAFT PULLEY  (See REMOVAL )
  47. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY  (See REMOVAL )
  48. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY  (See REMOVAL )
  49. REMOVE CRANKSHAFT POSITION SENSOR  (See REMOVAL )
  50. REMOVE TIMING CHAIN OR BELT COVER SUB-ASSEMBLY 
    1. Remove the 3 bolts and transverse engine mounting bracket.
      Fig 1: Installing Engine Mounting Bracket
      G05387105Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Using an E10 "TORX" socket, remove the stud bolt for the V-ribbed belt tensioner.
      Fig 2: Identifying Stud Bolt For V-Ribbed Belt Tensioner
      G06009437Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Remove the 12 bolts and 2 nuts.
      Fig 3: Locating Bolts And Nuts
      G06009438Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Remove the timing chain cover by prying the portions between the timing chain cover, cylinder head and cylinder block with a screwdriver.
      NOTE: Be careful not to damage the contact surfaces of the timing chain cover, cylinder head and cylinder block.

      HINT:

      Tape the screwdriver tip before use.

      Fig 4: Removing Timing Chain Cover
      G04975407Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  51. REMOVE TIMING CHAIN COVER OIL SEAL 
    1. Place the timing chain cover on wooden blocks.
    2. Using a screwdriver, pry out the oil seal.
      NOTE: Do not damage the surface of the oil seal press fit hole.

      HINT:

      Tape the screwdriver tip before use.

      Fig 5: Removing Timing Chain Case Oil Seal
      G04974264Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  52. REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE  (See REMOVAL )
  53. REMOVE TIMING CHAIN GUIDE  (See REMOVAL )
  54. REMOVE CHAIN TENSIONER SLIPPER  (See REMOVAL )
  55. REMOVE NO. 1 CHAIN VIBRATION DAMPER  (See REMOVAL )
  56. REMOVE CHAIN SUB-ASSEMBLY 
  57. REMOVE CRANKSHAFT TIMING GEAR OR SPROCKET  (See REMOVAL )
  58. REMOVE NO. 2 CHAIN SUB-ASSEMBLY  (See REMOVAL )
  59. REMOVE OIL PUMP ASSEMBLY 
    1. Remove the 3 bolts, oil pump and gasket.
      Fig 6: Identifying Bolts, Oil Pump And Gasket
      G04975409Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
scientia non olet · About LEMON Manuals