LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2008 >> FJ Cruiser RWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 196 (Audio System & Visual System) >> REAR PACKAGE TRAY SPEAKER (for Sedan) >> Installation

REAR PACKAGE TRAY SPEAKER (for Sedan): Installation

WARNING: This page is about a different car, the 2008 Toyota Yaris. However, it is still accessible from the selected car via links, so may be relevant.

HINT:

The procedure described below is for the RH side. Use the same procedure for both the RH and LH sides, unless otherwise specified.

  1. INSTALL REAR SPEAKER ASSEMBLY 
    1. Install the rear speaker with the 4 bolts.
    2. Connect the speaker connector.
      Fig 1: Locating Rear Speaker Bolts
      G04833673Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  2. INSTALL PACKAGE TRAY TRIM PAD 
    1. Install the package tray trim pad.
      Fig 2: Identifying Pack Age Tray Trim Pad
      G04833672Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  3. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY 
    1. Engage the 5 claws and install the package tray trim.
    2. Install the 4 clips.
      3. Fig 3: Locating Package Tray Trim Panel Claws
      G04833671Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  4. INSTALL HIGH MOUNTED STOP LIGHT ASSEMBLY (w/o Rear Spoiler)  (See INSTALLATION )
  5. INSTALL ROOF SIDE INNER GARNISH RH  (See INSTALLATION )
  6. INSTALL ROOF SIDE INNER GARNISH LH  (See INSTALLATION )
  7. INSTALL REAR SEAT SIDE COVER RH  (See INSTALLATION )
  8. INSTALL REAR SEAT SIDE COVER LH  (See INSTALLATION )
  9. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH 
    1. Install the rear door opening trim weatherstrip.
      2. Fig 4: Identifying Rear Door Opening Trim Weatherstrip
      G04833670Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  10. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH 

    HINT:

    Use the same procedure as for the RH side.

  11. INSTALL REAR DOOR SCUFF PLATE RH  (See INSTALLATION )
  12. INSTALL REAR DOOR SCUFF PLATE LH  (See INSTALLATION )
  13. INSTALL LUGGAGE COMPARTMENT TRIM INNER PAD (for 60/40 Split Seat Type)  (See INSTALLATION )
  14. INSTALL SPARE WHEEL COVER ASSEMBLY (for 60/ 40 Split Seat Type)  (See INSTALLATION )
  15. INSTALL LUGGAGE COMPARTMENT FLOOR MAT (for 60/40 Split Seat Type)  (See INSTALLATION )
  16. INSTALL REAR SEATBACK ASSEMBLY RH (for 60/ 40 Split Seat Type)  INSTALLATION 
  17. INSTALL REAR SEATBACK ASSEMBLY LH (for 60/40 Split Seat Type)  (See INSTALLATION )
  18. INSTALL REAR SEATBACK ASSEMBLY (for Fixed Seat Type)  INSTALLATION 
  19. INSTALL REAR SEAT CUSHION COVER PAD SUB-ASSEMBLY 
    1. for 60/40 Split Seat Type:
      1. Install the rear seat cushion cover pad sub-assembly (See INSTALLATION ).
    2. for Fixed Seat Type:
      1. Install the rear seat cushion cover pad sub-assembly INSTALLATION .
  20. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL 

    Torque: 5.4 N*m (55 kgf*cm, 48 in.*lbf) 

scientia non olet · About LEMON Manuals