Rear Seat Outer Belt Assembly: Installation

INSTALL REAR NO.2 SEAT OUTER BELT ASSEMBLY
1. Check the degree of tilt when the ELR begins to lock.
  1. Check that the belt does not lock at less than 15 degrees of tilt in any direction but locks at over 45 degrees of tilt when gently moving the installed retractor.
    NOTE: Do not disassemble the retractor.
    
    Fig 1: Identifying Degrees Of Tilt Seat Outer Belt
    Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Install the rear No.2 seat outer belt assembly with the 2 bolts.
  Torque: For upper bolt
  
  7.5 N*m (77 kgf*cm, 66 in.*lbf)
  
  For lower bolt
  
  42 N*m (428 kgf*cm, 31 ft.*lbf)
  
  Fig 2: Identifying Bolts And Rear No.2 Seat Outer Belt Assembly
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Install the shoulder anchor of the rear No.2 seat outer belt assembly with the bolt.
  Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf)
4. Install the seat belt anchor cover with the 2 claws.
5. Check if the ELR locks.
  NOTE: The check should be performed with the outer belt assembly installed.
  1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.
    
    Fig 3: Locating Bolt And Shoulder Anchor Of Rear No.2 Seat Outer Belt Assembly
    Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL REAR SEAT OUTER BELT ASSEMBLY
1. Check the degree of tilt when the ELR begins to lock.
  1. Check that the belt does not lock at less than 15 degrees of tilt in any direction but locks at over 45 degrees of tilt when gently moving the installed retractor.
    NOTE: Do not disassemble the retractor.
    
    Fig 4: Identifying Degree Of Tilt Rear Seat Belt
    Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Install the rear seat outer belt assembly with the claw and bolt.
  Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf)
  
  Fig 5: Identifying Rear Seat Outer Belt Assembly With Claw And Bolt
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Install the shoulder anchor of the rear seat outer belt assembly with the bolt.
  
  Fig 6: Locating Bolt And Shoulder Anchor Of Rear Seat Outer Belt Assembly
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  
  Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf)
INSTALL QUARTER PILLAR GARNISH
w/o Rear No.2 seat (See INSTALLATION )

w/ Rear No.2 seat (See INSTALLATION )
INSTALL DECK TRIM SIDE PANEL ASSEMBLY
w/o Rear No.2 seat (See INSTALLATION )

w/ Rear No.2 seat (See INSTALLATION )
CONNECT REAR SEAT OUTER BELT ASSEMBLY
1. Connect the floor end of the rear seat outer belt assembly with the bolt.
  Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf)
  
  NOTE: Do not allow the anchor part of the rear seat outer belt assembly and the protruding parts of the floor panel to overlap.
2. Check if the ELR locks.
  NOTE: The check should be performed with the outer belt assembly installed.
  1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.
    
    Fig 7: Identifying Protruding Parts
    Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL DECK TRIM SIDE PANEL ASSEMBLY FRONT
INSTALL REAR COMBINATION LIGHT SERVICE COVER
INSTALL ROPE HOOK
w/o Rear No.2 seat (See INSTALLATION )

w/ Rear No.2 seat (See INSTALLATION )
INSTALL DECK SIDE TRIM COVER
w/o Rear No.2 seat (See INSTALLATION )

w/ Rear No.2 seat (See INSTALLATION )
INSTALL DECK SIDE TRIM COVER FRONT
INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP
INSTALL REAR DOOR SCUFF PLATE
w/o Rear No.2 seat (See INSTALLATION )

w/ Rear No.2 seat (See INSTALLATION )
INSTALL REAR NO.2 SEAT ASSEMBLY (w/ Rear No. 2 Seat) (See INSTALLATION )
INSTALL REAR NO.1 SEAT ASSEMBLY RH (w/ Rear No. 2 Seat) (See INSTALLATION )
INSTALL SEAT TRACK COVER INNER RH (w/ Rear No. 2 Seat)
INSTALL REAR SEAT TRACK BRACKET COVER INNER RH (w/ Rear No. 2 Seat)
INSTALL REAR SEAT TRACK COVER RH (w/ Rear No. 2 Seat)
INSTALL REAR SEAT TRACK BRACKET COVER OUTER (w/ Rear No. 2 Seat)
INSPECT SLIDE ADJUSTER LOCK (w/ Rear No. 2 Seat) (See INSTALLATION )
INSTALL REAR NO.1 SEAT ASSEMBLY LH (w/ Rear No. 2 Seat) (See INSTALLATION )
INSTALL SEAT TRACK COVER INNER LH (w/ Rear No. 2 Seat)
INSTALL REAR SEAT TRACK BRACKET COVER INNER LH (w/ Rear No. 2 Seat)
INSTALL REAR SEAT TRACK COVER LH (w/Rear No. 2 Seat)
INSTALL REAR SEAT TRACK BRACKET COVER OUTER (w/ Rear No. 2 Seat)
INSTALL RECLINING HINGE COVER (w/ Rear No. 2 Seat)
INSPECT SLIDE ADJUSTER LOCK (w/ Rear No. 2 Seat) (See INSTALLATION )
INSTALL REAR NO.1 SEAT ASSEMBLY RH (w/o Rear No. 2 Seat) (See INSTALLATION )
INSTALL REAR NO.1 SEAT ASSEMBLY LH (w/o Rear No. 2 Seat) (See INSTALLATION )
INSTALL REAR SEAT TRACK BRACKET COVER INNER (w/o Rear No. 2 Seat)
INSTALL REAR SEAT TRACK BRACKET COVER OUTER (w/o Rear No. 2 Seat)
INSPECT SLIDE ADJUSTER LOCK (w/o Rear No. 2 Seat)
for LH Side (See INSTALLATION )

for RH Side (See INSTALLATION )
INSTALL DECK SIDE TRIM BOX LH
w/o Rear No.2 seat (See INSTALLATION )

w/ Rear No.2 seat (See INSTALLATION )
INSTALL DECK SIDE TRIM BOX RH
INSTALL JACK CARRIER ASSEMBLY
INSTALL JACK ASSEMBLY
INSTALL JACK CARRIER SUPPORT
INSTALL REAR SEAT RECLINING COVER NO.2 LH (w/ Rear No. 2 Seat) (See INSTALLATION )
INSTALL REAR SEAT RECLINING COVER NO.2 RH (w/ Rear No. 2 Seat)
INSTALL BACK DOOR WEATHERSTRIP
INSTALL REAR FLOOR FINISH PLATE
w/o Rear No.2 seat (See INSTALLATION )

w/ Rear No.2 seat (See INSTALLATION )
INSTALL DECK FLOOR BOX FRONT (w/o Rear No. 2 Seat) (See INSTALLATION )
INSTALL DECK FLOOR BOX REAR
w/o Rear No.2 seat (See INSTALLATION )

w/ Rear No.2 seat (See INSTALLATION )
INSTALL DECK BOARD SUB-ASSEMBLY NO.2
INSTALL DECK BOARD SUB-ASSEMBLY NO.3
INSTALL DECK BOARD SUB-ASSEMBLY
w/o Rear No.2 seat (See INSTALLATION )

w/ Rear No.2 seat (See INSTALLATION )
INSTALL TONNEAU COVER ASSEMBLY