Rear Center Seat Outer Belt Assembly: Installation

INSTALL REAR CENTER SEAT OUTER BELT ASSEMBLY
1. Check the degree of tilt when the ELR begins to lock.
  1. Check that the belt does not lock at less than 15 degrees of tilt in any direction but locks at over 45 degrees of tilt when gently moving the installed retractor.
    NOTE: Do not disassemble the retractor.
    
    Fig 1: Identifying Degree Of Tilt
    Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Install the rear center seat outer belt assembly with the bolt and nut.
  
  Fig 2: Identifying Bolt, Nut And Rear Center Seat Outer Belt Assembly
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  
  Torque: Bolt
  
  7.5 N*m (77 kgf*cm, 66 in.*lbf)
  
  Nut
  
  42 N*m (428 kgf*cm, 31 ft.*lbf)
INSTALL SEPARATE TYPE REAR SEATBACK COVER WITH PAD (w/ Rear No. 2 Seat) (See REASSEMBLY )
INSTALL REAR SEATBACK LOCK BEZEL UPPER (w/ Rear No. 2 Seat)
INSTALL REAR SEAT HEADREST SUPPORT (w/ Rear No. 2 Seat)
INSTALL REAR SEAT HEADREST SUPPORT (w/ Rear No. 2 Seat)
INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY (w/ Rear No. 2 Seat)
INSTALL REAR SEATBACK LOCK STRIKER COVER (w/ Rear No. 2 Seat)
INSTALL REAR SEAT HEADREST ASSEMBLY (w/ Rear No. 2 Seat)
INSTALL REAR SEAT BELT ASSEMBLY INNER (w/ Rear No. 2 Seat) (See INSTALLATION )
INSTALL SEPARATE TYPE REAR SEAT CUSHION ASSEMBLY (w/ Rear No. 2 Seat) (See REASSEMBLY )
INSTALL REAR SEAT CUSHION MOLDING REAR LH (w/ Rear No. 2 Seat)
INSTALL RECLINING HINGE COVER LH (w/ Rear No. 2 Seat)
INSTALL VERTICAL ADJUSTER BRACKET COVER LH (w/ Rear No. 2 Seat)
INSTALL REAR SEAT CUSHION MOLDING LH (w/ Rear No. 2 Seat)
INSTALL CENTER SEATBACK ASSEMBLY (w/ Rear No. 2 Seat) (See INSTALLATION )
INSTALL SEAT TRACK UPPER RAIL COVER LH (w/ Rear No. 2 Seat)
INSTALL CENTER SEAT HINGE COVER UPPER RH (w/ Rear No. 2 Seat)
INSTALL RECLINING COVER PROTECTOR RH (w/ Rear No. 2 Seat)
INSTALL REAR SEATBACK BOARD CARPET ASSEMBLY (w/ Rear No. 2 Seat)
INSTALL REAR SEATBACK COVER (w/ Rear No. 2 Seat)
INSTALL TONNEAU COVER HOOK HOLDER (w/ Rear No. 2 Seat)
INSTALL REAR NO.1 SEAT ASSEMBLY LH (w/ Rear No. 2 Seat) (See INSTALLATION )
INSTALL SEAT TRACK COVER INNER LH (w/ Rear No. 2 Seat)
INSTALL REAR SEAT TRACK BRACKET COVER INNER LH (w/ Rear No. 2 Seat)
INSTALL REAR SEAT TRACK COVER LH (w/ Rear No. 2 Seat)
INSTALL REAR SEAT TRACK BRACKET COVER OUTER (w/ Rear No. 2 Seat)
INSTALL RECLINING HINGE COVER (w/ Rear No. 2 Seat)
INSPECT SLIDE ADJUSTER LOCK (w/ Rear No. 2 Seat) (See INSTALLATION )
INSTALL SEPARATE TYPE REAR SEATBACK COVER WITH PAD (w/o Rear No. 2 Seat) (See REASSEMBLY )
INSTALL REAR SEATBACK LOCK BEZEL UPPER (w/ o Rear No. 2 Seat)
INSTALL REAR SEAT HEADREST SUPPORT (w/o Rear No. 2 Seat)
INSTALL REAR SEAT HEADREST SUPPORT (w/o Rear No. 2 Seat)
INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY (w/o Rear No. 2 Seat)
INSTALL REAR SEATBACK LOCK STRIKER COVER (w/o Rear No. 2 Seat)
INSTALL REAR SEAT HEADREST ASSEMBLY (w/o Rear No. 2 Seat)
REMOVE REAR SEAT BELT ASSEMBLY INNER (w/o Rear No. 2 Seat) (See INSTALLATION )
INSTALL SEPARATE TYPE REAR SEAT CUSHION ASSEMBLY (w/o Rear No. 2 Seat) (See REASSEMBLY )
INSTALL REAR SEAT CUSHION MOLDING REAR RH (w/o Rear No. 2 Seat)
INSTALL REAR SEAT CUSHION MOLDING RH (w/o Rear No. 2 Seat)
INSTALL CENTER SEATBACK ASSEMBLY (w/o Rear No. 2 Seat) (See INSTALLATION )
INSTALL CENTER SEAT HINGE COVER UPPER LH (w/o Rear No. 2 Seat)
INSTALL RECLINING COVER PROTECTOR LH (w/o Rear No. 2 Seat)
INSTALL REAR SEATBACK BOARD CARPET ASSEMBLY (w/o Rear No. 2 Seat)
INSTALL REAR SEATBACK COVER (w/o Rear No. 2 Seat)
INSTALL TONNEAU COVER HOOK HOLDER (w/o Rear No. 2 Seat)
INSTALL REAR NO.1 SEAT ASSEMBLY RH (w/o Rear No. 2 Seat) (See INSTALLATION )
INSTALL REAR SEAT TRACK BRACKET COVER INNER (w/o Rear No. 2 Seat)
INSTALL REAR SEAT TRACK BRACKET COVER OUTER (w/o Rear No. 2 Seat)
INSPECT SLIDE ADJUSTER LOCK (w/o Rear No. 2 Seat) (See INSTALLATION )