LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2007 >> Highlander Hybrid Limited, AWD >> Repair and Diagnosis >> Body & Frame >> Seats >> Seat (Hybrid) >> REAR NO. 1 SEAT ASSEMBLY (w/o Rear No. 2 Seat for RH Side) >> Reassembly

REAR NO. 1 SEAT ASSEMBLY (w/o Rear No. 2 Seat for RH Side): Reassembly

  1. INSTALL REAR SEAT TRACK ASSEMBLY INNER 
  2. INSTALL REAR SEAT TRACK ASSEMBLY OUTER 
  3. INSTALL REAR SEAT TRACK ADJUSTING HANDLE 
  4. INSTALL FOLD SEAT CUSHION FRAME NO.2 
    1. Install the 2 fold seat cushion frames No.2 with the 4 nuts.

      Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf) 

  5. INSTALL REAR SEATBACK FRAME SUB-ASSEMBLY LOWER 
    1. Temporarily install the rear seatback frame sub-assembly lower with the 5 "Torx" bolts.
    2. Using a "Torx" socket wrench (T55), tighten the 2 "Torx" bolts.

      Torque: 80 N*m (816 kgf*cm, 59 ft.*lbf) 

    3. Using a "Torx" socket wrench (T45), tighten the 3 "Torx" bolts.

      Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf) 

  6. INSTALL RECLINING CONTROL LINK SUB-ASSEMBLY 
    1. Install the reclining control link sub-assembly with the bolt and 4 nuts.

      Torque: Bolt 21 N*m (214 kgf*cm, 16 ft.*lbf) 

      Nut 42 N*m (428 kgf*cm, 31 ft.*lbf) 

    2. Install the 2 springs and 2 new E-rings.
  7. INSTALL SEAT TRACK STOP PLATE 
    1. Install the seat track stop plate with the 2 nuts.

      Torque: 18 N*m (184 kgf*cm, 13 ft.*lbf) 

    2. Install the 2 seat track stop plate cables.
    3. Install the clamp.
  8. INSTALL REAR SEATBACK FRAME SUB-ASSEMBLY 
    1. Temporarily install the rear seatback frame sub-assembly with the 2 bolts and 2 "Torx" bolts.
    2. Tighten the 2 bolts.

      Torque: 55 N*m (561 kgf*cm, 41 ft.*lbf) 

    3. Using a "Torx" socket wrench (T45), tighten the 2 "Torx" bolts.

      Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf) 

  9. INSTALL REAR SEAT RECLINING CONTROL CABLE 
  10. INSTALL REAR SEAT COVER NO.2 
  11. INSTALL REAR SEAT COVER NO.1 
  12. INSTALL REAR SEAT RECLINING COVER INNER RH 
  13. INSTALL FOLD SEAT STOPPER BAND ASSEMBLY NO.1 
  14. INSTALL REAR SEAT SHOULDER BELT COVER 
  15. INSTALL REAR CENTER SEAT OUTER BELT ASSEMBLY  (See INSTALLATION )
  16. INSTALL SEPARATE TYPE REAR SEATBACK PAD 
  17. INSTALL SEPARATE TYPE REAR SEATBACK COVER 
    1. Using hog ring pliers, install the separate type rear seatback cover to the separate type rear seatback pad with new hog rings.
      Fig 1: Installing Separate Type Rear Seat Cushion Cover To Rear Seat Cushion Pad With New Hog Rings
      G05244082Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      NOTE:
      • Be careful not to damage the cover.
      • When installing the hog rings, take care to minimize wrinkles as much as possible.
  18. INSTALL SEPARATE TYPE REAR SEATBACK COVER WITH PAD 
    1. Install the separate type rear seatback cover with pad to the rear seatback frame sub-assembly.
    2. Install the hook and new hog rings.
    3. Install the rear seat belt hook with the bolt.

      Torque: 6.0 N*m (61 kgf*cm, 53 in.*lbf) 

    4. Install the 2 clips.
    5. Install the floor anchor side of the rear center seat outer belt assembly with the bolt.
      Fig 2: Identifying Bolt
      G05244115Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf) 

    6. Check if the ELR locks.
      NOTE: The check should be performed with the outer belt assembly installed.
      1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.
  19. INSTALL REAR SEATBACK LOCK BEZEL UPPER 
  20. INSTALL REAR SEAT HEADREST SUPPORT 
  21. INSTALL REAR SEAT HEADREST SUPPORT 
  22. INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY 
  23. INSTALL REAR SEATBACK LOCK STRIKER COVER 
  24. INSTALL REAR SEAT HEADREST ASSEMBLY 
  25. INSTALL REAR SEAT BELT ASSEMBLY INNER  (See INSTALLATION )
  26. INSTALL REAR SEAT CUSHION PAD 
  27. INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER 
    1. Using hog ring pliers, install the separate type rear seat cushion cover to the rear seat cushion pad with new hog rings.
      Fig 3: Installing Separate Type Front Seatback Cover To Separate Type Front Seatback Pad With New Hog Rings
      G05244023Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      NOTE:
      • Be careful not to damage the cover.
      • When installing the hog rings, take care to minimize wrinkles as much as possible.
  28. INSTALL REAR SEAT CUSHION FRAME SUB-ASSEMBLY 
  29. INSTALL SEPARATE TYPE REAR SEAT CUSHION ASSEMBLY 
    1. Temporarily install the separate type rear seat cushion assembly with the 2 bolts and 2 "Torx" bolts.
    2. Tighten the 2 bolts.

      Torque: 18 N*m (184 kgf*cm, 13 ft.*lbf) 

    3. Install new hog rings.
    4. Using a "Torx" socket wrench (T45), tighten the 2 "Torx" bolts.

      Torque: 21 N*m (214 kgf*cm, 16 ft.*lbf) 

  30. INSTALL REAR SEAT CUSHION MOLDING REAR RH 
  31. INSTALL REAR SEAT CUSHION MOLDING RH 
  32. INSTALL CENTER SEAT BACK FRAME SUB-ASSEMBLY 
  33. INSTALL NO.2 CENTER SEATBACK COVER 
  34. INSTALL NO.1 SEATBACK COVER 
  35. INSTALL REAR SEAT HEADREST SUPPORT 
  36. INSTALL REAR SEAT HEADREST SUPPORT 
  37. INSTALL REAR SEAT ARMREST ASSEMBLY CENTER 
    1. Temporarily install the rear seat armrest assembly center with the nut and rear seat center armrest support.
    2. Using a "Torx" socket wrench (T45), install the rear seat armrest assembly center with the 2 "Torx" bolts.

      Torque: 21 N*m (214 kgf*cm, 16 ft.*lbf) 

  38. INSTALL REAR SEATBACK MOLDING RH 
    1. Install the rear seatback molding RH with the 3 screws.
    2. Using a "Torx" socket wrench (T45), install the rear seatback hinge sub-assembly center with the "Torx" bolts.

      Torque: 21 N*m (214 kgf*cm, 16 ft.*lbf) 

  39. INSTALL REAR SEATBACK MOLDING LH 
    1. Install the rear seatback molding LH with the 3 screws.
    2. Using a "Torx" socket wrench (T45), install the rear seatback hinge sub-assembly center with the "Torx" bolts.

      Torque: 21 N*m (214 kgf*cm, 16 ft.*lbf) 

  40. INSTALL RECLINING COVER PROTECTOR RH 
  41. INSTALL CENTER SEATBACK ASSEMBLY 
    1. Temporarily install the center seatback assembly with the 3 bolts and "Torx" bolt.
    2. Install the 3 bolts.

      Torque: 21 N*m (214 kgf*cm, 16 ft.*lbf) 

    3. Using a "Torx" socket wrench (T45), install the "Torx" bolt.

      Torque: 21 N*m (214 kgf*cm, 16 ft.*lbf) 

    4. Install the screw.
  42. INSTALL CENTER SEAT HINGE COVER UPPER LH 
  43. INSTALL RECLINING COVER PROTECTOR LH 
  44. INSTALL REAR SEATBACK BOARD CARPET ASSEMBLY 
  45. INSTALL REAR SEATBACK COVER 
  46. INSTALL TONNEAU COVER HOOK HOLDER 
  47. INSTALL REAR SEAT HEADREST ASSEMBLY CENTER 
scientia non olet · About LEMON Manuals