Rear Suspension Arm ASSY No. 2: Replacement

HINT:

• COMPONENTS: See COMPONENTS .
• Use the same procedures for the RH side and LH side.
• The procedures listed below are for the LH side.

1. REMOVE REAR WHEEL 
2. REMOVE EXHAUST PIPE ASSY CENTER (SEE  REPLACEMENT  ) 
3. REMOVE STABILIZER BAR REAR (SEE  REPLACEMENT  ) 
4. REMOVE STRUT ROD ASSY REAR (SEE  REPLACEMENT  ) 
5. SEPARATE HEIGHT CONTROL SENSOR SUB-ASSY REAR RH (w/DISCHARGE HEAD LIGHT) (SEE  ADJUSTMENT  ) 
6. SEPARATE REAR SUSPENSION ARM ASSY NO. 1 LH (SEE  REPLACEMENT  ) 
7. SEPARATE REAR SUSPENSION ARM ASSY NO. 1 RH 

   HINT:

   Separate the RH side using the same procedures as for the LH side.

8. SEPARATE REAR SUSPENSION ARM ASSY NO. 2 LH (SEE  REPLACEMENT  ) 
9. SEPARATE REAR SUSPENSION ARM ASSY NO. 2 RH 

   HINT:

   Separate the RH side using the same procedures as for the LH side.

10. REMOVE REAR SUSPENSION MEMBER SUB-ASSY (SEE  REPLACEMENT  ) 
11. REMOVE REAR SUSPENSION ARM ASSY NO. 2 LH 
    1. Remove the bolt, and disconnect the rear suspension arm No. 2 (inner side).
       Fig 1: Removing Bolt, & Disconnect Rear Suspension Arm No. 2 (Inner Side)

       Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
12. INSTALL REAR SUSPENSION ARM ASSY NO. 2 LH 
    1. Install the rear suspension arm No. 2 (inner side) with the bolt.

       Torque: 100 N.m (1,020 kgf.cm, 74 ft.lbf) 

       Fig 2: Installing Rear Suspension Arm No. 2 (Inner Side) With Bolt

       Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

       HINT:

       Ensure that the paint marks face the rear side of the vehicle.

       Fig 3: Ensuring That Paint Marks Face Rear Side Of Vehicle

       Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
13. INSTALL REAR SUSPENSION MEMBER SUB-ASSY (SEE  REPLACEMENT  ) 
14. TEMPORARILY TIGHTEN REAR SUSPENSION ARM ASSY NO. 1 LH (SEE  REPLACEMENT  ) 
15. TEMPORARILY TIGHTEN REAR SUSPENSION ARM ASSY NO. 1 RH 

    HINT:

    Temporarily tighten the RH side using the same procedures as for the LH side.

16. TEMPORARILY TIGHTEN REAR SUSPENSION ARM ASSY NO. 2 LH (SEE  REPLACEMENT  ) 
17. TEMPORARILY TIGHTEN REAR SUSPENSION ARM ASSY NO. 2 RH 

    HINT:

    Temporarily tighten the RH side using the same procedures as for the LH side.

18. TEMPORARILY TIGHTEN STRUT ROD ASSY REAR (SEE  REPLACEMENT  ) 
19. STABILIZE SUSPENSION (SEE  REPLACEMENT  ) 
20. FULLY TIGHTEN REAR SUSPENSION ARM ASSY NO. 1 LH (SEE  REPLACEMENT  ) 
21. FULLY TIGHTEN REAR SUSPENSION ARM ASSY NO. 1 RH 

    HINT:

    Fully tighten the RH side using the same procedures as for the LH side.

22. FULLY TIGHTEN REAR SUSPENSION ARM ASSY NO. 2 LH (SEE  REPLACEMENT  ) 
23. FULLY TIGHTEN REAR SUSPENSION ARM ASSY NO. 2 RH 

    HINT:

    Fully tighten the RH side using the same procedures as for the LH side.

24. FULLY TIGHTEN STRUT ROD ASSY REAR (SEE  REPLACEMENT  ) 
25. INSTALL STABILIZER BAR REAR (SEE  REPLACEMENT  ) 
26. INSTALL HEIGHT CONTROL SENSOR SUB-ASSY REAR RH (w/DISCHARGE HEAD LIGHT) (SEE  REPLACEMENT  ) 
27. INSTALL EXHAUST PIPE ASSY CENTER (SEE  REPLACEMENT  ) 
28. INSTALL REAR WHEEL 

    Torque: 103 N.m (1,050 kgf.cm, 76 ft.lbf) 

29. INSPECT REAR WHEEL ALIGNMENT (SEE  ADJUSTMENT  ) 
30. HEAD LIGHT AIMING ADJUSTMENT (w/DISCHARGE HEAD LIGHT) (SEE  ADJUSTMENT  )