Engine Unit: Disassembly

1. Using a 12 mm socket hexagon wrench, remove the oil filter union.

1. Remove the oil pan drain plug and gasket.

1. Using several steps, uniformly loosen and remove the 20 bearing cap bolts in the sequence shown in the illustration.
2. Remove the 10 bearing caps, then remove the camshaft and No. 2 camshaft.
Fig 1: Identifying Bearing Cap Bolts In Sequence
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Using a 6 mm socket hexagon wrench, remove the plug and gasket.
2. Remove the oil control valve filter.
   Fig 2: Identifying Oil Control Valve Filter

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Remove the plug from the cylinder block.
   Fig 3: Identifying Plug From Cylinder Block

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Using a dial indicator, measure the thrust clearance while moving the balance shaft back and forth.

   Standard thrust clearance: 

   0.05 to 0.09 mm (0.0020 to 0.0035 in.) Maximum thrust clearance: 

   0.09 mm (0.0035 in.) 

   If the thrust clearance is greater than the maximum, replace the balance shaft housing and bearings. If necessary, replace the balance shaft.

   Fig 4: Measuring Thrust Clearance

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Using several steps, uniformly loosen and remove the 8 bolts in the sequence shown in the illustration.
2. Remove the balance shaft housing from the crankcase.

   HINT:

   Keep the lower bearing and balance shaft housing together.

3. Lift out the No. 1 and No. 2 balance shafts.

   HINT:

   Keep the upper bearing with the crankcase.

   Fig 5: Identifying Balance Shaft Housing Bolts Sequence

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
4. Clean each bearing and journal.
5. Check each bearing and journal for pitting and scratches.

   If a bearing or journal is damaged, replace the bearings. If necessary, replace the balance shaft.

6. Place the No. 1 and No. 2 balance shafts onto the crankcase.
7. Lay a strip of Plastigage across each journal, (h) Install the balance shaft housing.
Fig 6: Inspecting Balance Shaft
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
8. Apply a light coat of engine oil on the threads and under the heads of the bolts.
9. Using several steps, uniformly install and tighten the 8 bolts in the sequence shown in the illustration.

   Torque: 21.6 N*m (220 kgf*cm, 16 ft.*lbf) 

   Fig 7: Identifying Tighten Bolts Sequence

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
10. Mark the front of the bolts with paint.
Fig 8: Identifying Retighten Bolts Paint Mark
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
11. Retighten the bolts 90° as shown in the illustration.
12. Check that the paint mark is now at a 90° angle to the front, (n) Remove the balance shaft housing from the crankcase.
13. Measure the Plastigage at its widest point.

    Standard oil clearance: 

    0.004 to 0.049 mm (0.0002 to 0.0019 in.) 

    Maximum oil clearance: 

    0.049 mm (0.0019 in.) 

    NOTE: Remove the Plastigage completely after the measurement.

    If the oil clearance is greater than the maximum, replace the bearing. If necessary, replace the balance shaft.

    HINT:

    If replacing a bearing, select a new one with the same number.

    Standard balance shaft housing journal bore diameter 

    STANDARD BALANCE SHAFT HOUSING JOURNAL BORE DIAMETER SPECIFIED CONDITION REFERENCE
    
    

    Item	Specified Condition
    Mark 1	26.000 to 26.006 mm (1.0236 to 1.0239 in.)
    Mark 2	26.007 to 26.012 mm (1.0239 to 1.0214 in.)
    Mark 3	26.013 to 26.018 mm (1.0241 to 1.0243 in.)

    Standard balance shaft journal diameter: 

    22.985 to 23.000 mm (0.9049 to 0.9055 in.) 

    Standard bearing center wall thickness 

    STANDARD BEARING CENTER WALL THICKNESS SPECIFIED CONDITION REFERENCE
    
    

    Item	Specified Condition
    Mark 1	1.486 to 1.489 mm (0.0585 to 0.0586 in.)
    Mark 2	1.490 to 1.492 mm (0.0587 to 0.0587 in.)
    Mark 3	1.493 to 1.495 mm (0.0588 to 0.0589 in.)

1. Using a knife, cut off the lip of the oil seal.
2. Using a screwdriver with its tip wrapped with tape, pry out the oil seal.
   NOTE: After removing, check the crankshaft for damage. If damaged, smooth the surface with 400-grit sandpaper.
   Fig 9: Cutting Off Lip Of Oil Seal

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Using several steps, uniformly loosen and remove the 11 bolts in the sequence shown in the illustration.
2. Remove the crankcase by prying the portions between the crankcase and cylinder block.
   NOTE: Be careful not to damage the contact surfaces of the crankcase and cylinder bock.
3. Remove the O-ring from the cylinder block.
   Fig 10: Identifying Stiffening Crankcase Assembly Bolts Sequence

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Using a dial indicator, measure the thrust clearance while moving the connecting rod back and forth.

   Standard thrust clearance: 

   0.160 to 0.362 mm (0.0063 to 0.0143 in.) 

   Maximum thrust clearance: 

   0.362 mm (0.0143 in.) 

   If the thrust clearance is greater than the maximum, replace the connecting rod. If necessary, replace the crankshaft.

   Fig 11: Inspecting Connecting Rod Thrust Clearance

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Using marking paint, write the matched cylinder number on each connecting rod and cap.

   HINT:

   The matchmarks in the connecting rods and caps are for ensuring correct reassembly.

2. Using a 12 mm socket wrench, remove the 2 bolts and connecting rod cap.
3. Clean the crank pin and bearing.
4. Check the crank pin and bearing for pitting and scratches.
   Fig 12: Locating Connecting Rods Caps And Bolts

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
5. Lay a strip of Plastigage on the crank pin.
Fig 13: Laying Strip Of Plastigage On Crank Pin
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
6. (Check that the front mark of the connecting rod cap is facing in the correct direction.
7. Apply a light coat of engine oil to the threads and under the heads of the connecting rod bolts.
8. Using a 12 mm socket wrench, tighten the bolts in several passes to the specified torque.

   Torque: 24.5 N*m (250 kgf*cm, 18 ft.*lbf) 

9. Mark the front of the connecting rod bolts with paint.
Fig 14: Identifying Retighten Bolts Paint Mark
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
10. Retighten the cap bolts 90° as shown in the illustration.
11. Check that the crankshaft turns smoothly.
12. Using a 12 mm socket wrench, remove the 2 bolts and connecting rod cap.
13. Measure the Plastigage at its widest point.

    Standard oil clearance: 

    0.024 to 0.048 mm (0.0009 to 0.0019 in.) 

    Maximum oil clearance: 

    0.08 mm (0.0032 in.) 

    NOTE: Remove the Plastigage completely after the measurement.

    If the oil clearance is greater than the maximum, replace the connecting rod bearing. If necessary, grind or replace the crankshaft.

    HINT:

    If replacing a bearing, select a new one with the same number as marked on the connecting rod.

    There are 3 sizes of standard bearings, marked "1", "2" and "3" accordingly.

    Standard connecting rod large end bore diameter 

    STANDARD CONNECTING ROD LARGE END BORE DIAMETER SPECIFIED CONDITION REFERENCE
    
    

    Mark	Specified Condition
    Mark 1	51.000 to 51.007 mm (2.0079 to 2.0082 in.)
    Mark 2	51.008 to 51.013 mm (2.0082 to 2.0084 in.)
    Mark 3	51.014 to 51.020 mm (2.0084 to 2.0087 in.)

    Standard connecting rod bearing thickness 

    STANDARD CONNECTING ROD BEARING THICKNESS SPECIFIED CONDITION REFERENCE
    
    

    Mark	Specified Condition
    Mark 1	1.485 to 1.488 mm (0.0585 to 0.0586 in.)
    Mark 2	1.489 to 1.491 mm (0.0586 to 0.0587 in.)
    Mark 3	1.492 to 1.494 mm (0.0587 to 0.0588 in.)

    Standard crankshaft pin diameter 

    STANDARD CRANKSHAFT PIN DIAMETER SPECIFIED CONDITION REFERENCE
    
    

    Mark	Specified Condition
    -	47.990 to 48.000 (1.8894 to 1.8898 in.)

1. Using a ridge reamer, remove all the carbon from the top of the cylinder.
2. Push the piston, connecting rod assembly and upper bearing through the top of the cylinder block.

   HINT:

   • Keep the bearing, connecting rod and cap together.
   • Arrange the piston and connecting rod assemblies in the correct order.
     Fig 15: Pushing Piston

     Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Using a piston ring expander, remove the 2 compression rings.
2. Remove the 2 side rails and expander by hand.
   Fig 16: Removing Piston Ring Set

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Using a small screwdriver, pry out the 2 snap rings.
   Fig 17: Removing Piston Pin Hole Snap Ring

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Gradually heat the piston up to 80 to 90°C (176 to 194°F).
   Fig 18: Identifying Piston With Connecting Rod Gradually Heat

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Using a plastic hammer and brass bar, lightly tap out the piston pin, then remove the connecting rod.

   HINT:

   • The piston and pin are a matched set.
   • Arrange the piston, pin, ring, connecting rod and bearings in the correct order.
     Fig 19: Removing Connecting Rod

     Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Using a dial indicator, measure the thrust clearance while prying the crankshaft back and forth with a screwdriver.

   Standard thrust clearance: 

   0.04 to 0.24 mm (0.0016 to 0.0095 in.) 

   Maximum thrust clearance: 

   0.30 mm (0.0118 in.) 

   If the thrust clearance is greater than the maximum, replace the thrust washers as a set.

   HINT:

   The thrust washer thickness is 1.93 to 1.98 mm (0.0760 to 0.0780 in.).

   Fig 20: Measuring Thrust Clearance Crankshaft Back And Forth

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Clean each main journal and bearing.
2. Check each main journal and bearing for pitting and scratches.
3. Install the upper bearing with an oil groove onto the cylinder block.
   NOTE: Do not apply engine oil to the bearing or its contact surface.
   Fig 21: Installing Upper Bearing With Oil Groove Onto Cylinder Block

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
4. Install the lower bearing onto the bearing cap.
   NOTE: Do not apply engine oil to the bearing or its contact surface.
5. Place the crankshaft onto the cylinder block.
   Fig 22: Installing Lower Bearing Onto Bearing Cap

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
6. Lay a strip of Plastigage across each journal.
   Fig 23: Laying Strip Of Plastigage Journal

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
7. Examine the front marks and numbers and install the bearing caps onto the cylinder block in the order shown in the illustration.
8. Apply a light coat of engine oil to the threads and under the heads of the bearing cap bolts.
   Fig 24: Identifying Front Marks On Bearing Caps

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
9. Using several steps, uniformly install and tighten the 10 bearing cap bolts in the sequence shown in the illustration.

   Torque: 40 N*m (408 kgf*cm, 30 ft.*lbf) 

   Fig 25: Identifying Bearing Cap Bolts In Sequence

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
10. Mark the front of the bearing cap bolts with paint.
Fig 26: Identifying Retighten Bolts Paint Mark
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
11. Retighten the 10 bearing cap bolts by 90°.
12. Check that the paint marks are at a 90° angle to the front.
13. Remove the bearing caps.
14. Measure the Plastigage at its widest point.

    Standard oil clearance: 

    0.017 to 0.040 mm (0.0007 to 0.0016 in.) 

    Maximum oil clearance: 

    0.050 mm (0.0020 in.) 

    NOTE: Remove the Plastigage completely after the measurement.

    If the oil clearance is greater than the maximum, replace the crankshaft bearing. If necessary, replace the crankshaft.

    HINT:

    If replacing a bearing, select a new one with the same number. If the number of the bearing cannot be determined, calculate the correct bearing number by adding together the numbers imprinted on the cylinder block and crankshaft. Then select a new bearing with the calculated number. There are 4 sizes of standard bearings, marked "1", "2", "3" and "4" accordingly.

    SPECIFIED CONDITION REFERENCE
    
    

    Cylinder block + Crankshaft	0 to 2	3 to 5	6 to 8	9 to 11
    Use bearing	"1"	"2"	"3"	"4"

    EXAMPLE

    • Imprinted number on the cylinder block is 3.
    • Imprinted number on the crankshaft is 4. 3 + 4 = 7

    Select the bearing marked "7".

    Standard cylinder block journal bore diameter 

    STANDARD CYLINDER BLOCK JOURNAL BORE DIAMETER SPECIFIED CONDITION REFERENCE
    
    

    Mark	Specified Condition
    0	59.000 to 59.002 mm (2.3228 to 2.3229 in.)
    1	59.003 to 59.004 mm (2.3230 to 2.3230 in.)
    2	59.005 to 59.006 mm (2.3230 to 2.3231 in.)
    3	59.007 to 59.009 mm (2.3231 to 2.3232 in.)
    4	59.010 to 59.011 mm (2.3232 to 2.3233 in.)
    5	59.012 to 59.013 mm (2.3233 to 2.3234 in.)
    6	59.014 to 59.016 mm (2.3234 to 2.3235 in.)

    Standard crankshaft journal diameter 

    STANDARD CRANKSHAFT JOURNAL DIAMETER SPECIFIED CONDITION REFERENCE
    
    

    Mark	Specified Condition
    0	54.999 to 55.000 mm (2.1653 to 2.1654 in.)
    1	54.997 to 54.998 mm (2.1652 to 2.1653 in.)
    2	54.995 to 54.996 mm (2.1652 to 2.1652 in.)
    3	54.993 to 54.994 mm (2.1651 to 2.1651 in.)
    4	54.991 to 54.992 mm (2.1650 to 2.1650 in.)
    5	54.988 to 54.990 mm (2.1649 to 2.1650 in.)

    Standard bearing center wall thickness 

    STANDARD BEARING CENTER WALL THICKNESS SPECIFIED CONDITION REFERENCE
    
    

    Mark	Specified Condition
    1	1.993 to 1.996 mm (0.0785 to 0.0786 in.)
    2	1.997 to 1.999 mm (0.0786 to 0.0787 in.)
    3	2.000 to 2.002 mm (0.0787 to 0.0788 in.)
    4	2.003 to 2.005 mm (0.0789 to 0.0789 in.)

1. Using several steps, uniformly loosen and remove the 10 bearing cap bolts in the sequence shown in the illustration.
2. Remove the 5 bearing caps from the cylinder block.
3. Remove the crankshaft from the cylinder block.
Fig 27: Identifying Bearing Cap Bolts In Sequence
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

HINT:

Arrange the bearings in the correct order.

HINT:

Arrange the bearings in the correct order.

1. Remove the 8 stud bolts.