LEMON Manuals: Even more car manuals for everyone
Home >> Porsche >> 2016 >> 911 Turbo, 2D Convertible >> Repair and Diagnosis >> External Pages >> Different car >> Section 130 (97 - Cables -- CARRERA (997)) >> WM 972519 Removing And Installing Rear Wire Harness (All Models) >> Installing Rear Wire Harness >> Notes

Installing Rear Wire Harness: Notes

WARNING: This page does not describe the selected car, but rather 9 other vehicles, including the 2013 Porsche 911, 2012 Porsche 911, 2011 Porsche 911, 2010 Porsche 911, and 2009 Porsche 911. However, it is still accessible from the selected car via links, so may be relevant.
Fig 1: Overview Of Connectors For Rear Wire Harness
G09831208Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  1. 1  - Plug connection for main wire harness to rear wire harness, left and right
  2. 2  - Connector for Tiptronic control unit
  3. 3  - Connector for seat-belt pretensioner, left and right
  4. 4  - Connector for rear loudspeaker, left and right
  5. 6  - Plug connection for rear window heating, left and right
  6. 7  - Connector for DME control unit
  7. 8  - Rear relay carrier
  8. 9  - PASM connector, left and right
  9. 10  - Subwoofer connector
  10. 11  - Connector for additional brake light
  11. 12  - Connector for wiper motor for rear window washer
  12. 13  - Ground point, left and right
  13. 14  - Connector for rear light, left and right
  14. 15  - Connector for engine coolant level switch
  15. 16  - Plug connection for oxygen sensor, left and right
  16. 17  - Plug connection for rear lock lower part
  17. 18  - Connector for motor for rear lid release
  18. 19  - Plug connection for wire harness for number plate light
  19. 20  - Plug for hot-film mass air flow meter
  20. 21  - Connector for air cleaner flap
  21. 22  - Plug connection for rear wire harness to wire harness for rear lid
  22. 23  - Plug connection for rear wire harness to engine wire harness
  23. 24  - Connector for angle sensor for range adjustment, rear left
  24. 25  - Plug connection for rear wheel sensor, left and right
  25. 26  - Connector for tire pressure monitoring system antenna, rear left and right
  26. 27  - B+ lead for transmission
  27. 28  - Connector for reversing light switch
  28. 29  - Cable duct
  29. 30  - Rubber sleeves
  30. 31  - Tie-wrap
  1. Lay rear wire harness in interior of vehicle and push it into the engine compartment through the opening in the rear wall. Lay rear wire harness in engine compartment.
  2. Plug in connector on reversing light switch -28-  until it engages correctly. → Installing Switch For Reversing Light - section on "Installing"
  3. Screw on B+ lead -27-  on transmission. → Tightening torque: 10 Nm (7.5 ft. lb.)  → Installing Transmission - section on "Installing"
  4. Plug in connector on rear antenna for tire pressure monitoring system -26-  at the left and right. → Installing Antenna For Tire Pressure Monitoring (TPM) - section on "Installing"
    1. 4.1. Fit rubber sleeve -30-  .
    2. 4.2. Plug in connector on rear antenna for tire pressure monitoring system -26-  at the left and right until it engages securely.
    3. 4.3. Clip tie-wrap -31-  into place.
  5. Connect plug connection for rear wheel sensor -25-  at the left and right.
    Fig 2: Connecting Plug Connection For Rear Wheel Sensor
    G09831209Courtesy of PORSCHE CARS NORTH AMERICA, INC.
    1. 5.1. Fit rubber sleeve -30-  .
    2. 5.2. Place socket in installation position -arrow A-  and screw on the fastening nut. → Tightening torque: 10 Nm (7.5 ft. lb.) 
    3. 5.3. Plug in the two connectors -arrow B-  .
    4. 5.4. Fold back the cable retainer -arrow C-  until it engages correctly at the connectors.
  6. Connect connector on angle sensor for range adjustment at the rear left -24-  . → Installing Rear Angle Sensor For Headlight Beam Adjustment (HBA) - section on "Installing"
    1. 6.1. Fit rubber sleeve -30-  .
    2. 6.2. Plug in connector on rear left angle sensor for range adjustment -24-  until it engages securely.
  7. Connect plug connection for rear wire harness to engine wire harness -23-  . → Installing Engine - section on "Installing"
    Fig 3: Identifying Plug Connection For Rear To Engine Wire Harness
    G09831210Courtesy of PORSCHE CARS NORTH AMERICA, INC.
    1. 7.1. Connect rear wire harness at the two plug connections and lock it by turning the bayonet locks clockwise.
  8. Push plug connection for rear wire harness to wire harness for rear lid together -22-  until it engages securely. → Installing rear lid - section on "Installing"
  9. Plug in connector on motor for rear lid release -18-  until it engages securely. → Installing motor for rear lid release - section on "Installing"
  10. Push plug connection on rear lock lower part -17-  together until it engages securely. → Installing lower part of lid lock at rear - section on "Installing"
  11. Push in plug connection for lambda sensor -16-  at the left and right until it engages securely. → Installing Lambda Sensor Upstream Of Catalytic Converter - section on "Installing"
  12. Clip tie-wrap -31-  into place.
  13. Clip in cable duct -29-  .
  14. Fasten ground point -13-  at the left and right.
    Fig 4: Securing Ground Point
    G09831211Courtesy of PORSCHE CARS NORTH AMERICA, INC.
    1. 14.1. Connect ground straps and screw down fastening nut. → Tightening torque: 9 Nm (6.5 ft. lb.) 
  15. Plug in connector on wiper motor for rear window washer -12-  until it engages correctly. → Installing wiper motor for rear window washer - section on "Installing"
  16. Plug in connector on subwoofer -10-  until it engages securely. → Installing Subwoofer - section on "Installing"
  17. Connect PASM plug connection -9-  at the left and right.
    Fig 5: Connecting PASM Plug Connection
    G09831212Courtesy of PORSCHE CARS NORTH AMERICA, INC.
    1. 17.1. Connect PASM plug connection -9-  until it engages securely.
  18. Plug in connector on DME control unit -7-  until it engages securely. → Installing DME (DFI) Control Unit - section on "Installing"
  19. Push in plug connection for rear window heating -6-  at the left and right until it engages securely. → Installing Rear Window - section on "Installing"
  20. Plug in connector on seat-belt pretensioner -3-  at the left and right. → Installing Front Three-Point Belt - section on "Installing"
    1. 20.1. Fit rubber sleeve -30-  .
    2. 20.2. Plug in connector on seat-belt pretensioner -3-  at the left and right until it engages securely.
  21. Push on connector for Tiptronic control unit -2-  until it engages securely, and lock it. → Installing Tiptronic Control Unit - section on "Installing"
  22. Push plug connection for main wire harness to rear wire harness -1-  together at the left and right.
    Fig 6: Connecting Plug Connection For Main To Rear Wire Harness
    G09831213Courtesy of PORSCHE CARS NORTH AMERICA, INC.
    1. 22.1. Connect plug connection for main wire harness to rear wire harness -1-  and lock it.
scientia non olet · About LEMON Manuals