LEMON Manuals: Even more car manuals for everyone
Home >> Porsche >> 2016 >> 911 Turbo, 2D Convertible >> Repair and Diagnosis >> External Pages >> Different car >> Section 130 (97 - Cables -- CARRERA (997)) >> WM 970919 Removing And Installing Main Wire Harness (All Models) >> Installing Main Wire Harness >> Installing Main Wire Harness In Passenger Compartment

Installing Main Wire Harness In Passenger Compartment

WARNING: This page does not describe the selected car, but rather 9 other vehicles, including the 2013 Porsche 911, 2012 Porsche 911, 2011 Porsche 911, 2010 Porsche 911, and 2009 Porsche 911. However, it is still accessible from the selected car via links, so may be relevant.
Fig 1: Overview Of Connectors For Main Wire Harness In Dashboard
G09831125Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  1. 1-3  - Connector for steering column switch
  2. 4  - Connector for main light switch
  3. 5  - Connector for ignition lock
  4. 6  - Connector for diagnostic box
  5. 7  - Connector for footwell light, left
  6. 8  - Connector for instrument cluster
  7. 9-10  - Connector for passenger's airbag, stage 1 and stage 2
  8. 11  - Connector for footwell light, right
  9. 12  - Plug connection for glove box
  10. 13  - Connector for stopwatch
  11. 14  - Connector for sun sensor
  12. 15  - Connector for center speaker
  13. 16-17  - Connector for loudspeaker, left and right
  14. 18  - Connector for switch console
  15. 19-20  - Connector for climate control
  16. 21-26  - Connector for PCM
  17. 27  - Connector for central locking
  18. 28  - Connector for hazard warning light switch
  19. 29-30  - Plug connection for illumination of center nozzle
  20. 31-32  - Plug connection for illumination of left and right nozzle
Fig 2: Overview Of Connectors For Main Wire Harness In Passenger Compartment
G09831126Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  1. 33-34  - Plug connection between main wire harness and rear wire harness, left and right
  2. 35-36  - Connector for loudspeaker, rear left and right
  3. 37-38  - Connector for front seat-belt pretensioner, left and right
  4. 39-40  - Rubber sleeve
  5. 41  - Connector for Tiptronic control unit
  6. 42-43  - Connector for airbag sensor, center left and right
  7. 44-45  - Connector for ParkAssist control unit
  8. 46-48  - Connector for control unit for rear convenience systems
  9. 49  - Ground point under driver's seat
  10. 50-53  - Connector for telephone control unit
  11. 54  - Ground point under passenger's seat
  12. 55-56  - Connector for front seat, left and right
  13. 57  - Connector for driver's seat with memory
  14. 58  - Connector for door sill button module
  15. 59-60  - Plug connection between main wire harness and wire harness for door, left and right
  16. 61  - Fuse box
  17. 62  - Relay carrier
  18. 63-64  - Connector for vehicle electrical system control unit
  19. 65  - Connector for gateway control unit
  20. 66-67  - Connector for KESSY/PAS control unit
  21. 68  - Connector for brake light switch
  22. 69  - Connector for pedal sensor
  23. 70  - Plug connection between main wire harness and wire harness for center console
  24. 71  - Plug connection for telephone handset
  25. 72  - Connector for airbag triggering unit
  26. 73  - Connector for parking-brake lever contact switch
  27. 74-75  - Tiptronic position switch
  28. 76  - Ground point under unit carrier
  29. 77  - Connector for tilt sensor control unit
  30. 78  - Power distributor
  31. 79-80  - Plug connection between main wire harness and wire harness for heater/air-conditioning unit
  32. 81-82  - Connector for garage door opener control unit
  33. 83  - Connector for sunroof switch
  34. 84  - Connector for interior light
  35. 85  - Connector for sunroof motor
  36. 86  - Plug connection for rain sensor
  37. 87-88  - Plug connection for make-up mirror, left and right
  38. 89-93  - Connector for antenna unit, left and right
  1. Fasten main wire harness at center dashboard bracket.
    Fig 3: Installing Main Wire Harness At Center Dashboard Bracket
    G09831127Courtesy of PORSCHE CARS NORTH AMERICA, INC.
    1. 1.1. Lay main wire harness and fasten with four new tie-wraps.
  2. Fasten main wire harness at right dashboard bracket.
    Fig 4: Installing Main Wire Harness At Right Dashboard Bracket
    G09831128Courtesy of PORSCHE CARS NORTH AMERICA, INC.
    1. 2.1. Clip in main wire harness on both cable guides.
  3. Fasten main wire harness at left dashboard bracket.
    Fig 5: Installing Main Wire Harness At Left Dashboard Bracket
    G09831129Courtesy of PORSCHE CARS NORTH AMERICA, INC.
    1. 3.1. Clip in main wire harness on cable guide.
    2. 3.2. Insert fastening screw and tighten fastening nut. → Tightening torque: 3.5 Nm (2.5 ft. lb.) 
  4. Fasten holder for relay carrier.
    Fig 6: Installing Holder For Relay Carrier
    G09831130Courtesy of PORSCHE CARS NORTH AMERICA, INC.
    1. 4.1. Position holder for relay carrier and tighten with the two fastening screws to the dashboard bracket. → Tightening torque: 3.5 Nm (2.5 ft. lb.) 
  5. Clip in cable guide on dashboard bracket.
    Fig 7: Clipping In Cable Guide
    G09831131Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  6. Clip in length compensation at the steering column.
    Fig 8: Clipping In Length Compensation
    G09831132Courtesy of PORSCHE CARS NORTH AMERICA, INC.
    1. 6.1. Position length compensation at the steering column and fasten with the expansion rivet.
  7. Fasten ground points on dashboard bracket.
    Fig 9: Installing Ground Points On Dashboard Bracket
    G09831133Courtesy of PORSCHE CARS NORTH AMERICA, INC.
    1. 7.1. Fit ground straps and tighten with fastening nuts. → Tightening torque: 9 Nm (6.5 ft. lb.) 
  8. Push on connector for antenna amplifier, left and right -89 to 93-  . → 918419 REMOVING AND INSTALLING ANTENNA AMPLIFIER - section on "Installing"
  9. Remove protective film of adhesive strip on main wire harness -area A-  and affix main wire harness to A-pillar.
    Fig 10: Locating Main Wire Harness Area Of A-Pillar
    G09831134Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  10. Clip in main wire harness at front of roof frame.
    Fig 11: Clipping In Main Wire Harness At Front Of Roof Frame
    G09831135Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  11. Clip in cable duct at front of roof frame.
    Fig 12: Clipping In Cable Duct At Front Of Roof Frame
    G09831136Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  12. Connect plug connection of make-up mirror, left and right -87 and 88-  .
    Fig 13: Connecting Plug Connection Of Mirror
    G09831137Courtesy of PORSCHE CARS NORTH AMERICA, INC.
    1. 12.1. Connect plug connection -arrows A-  until it engages securely.
    2. 12.2. Clip plug connection into console -arrow B-  .
  13. Connect plug connection -86-  until it engages securely. → 921219 REMOVING AND INSTALLING RAIN SENSOR - section on "Installing"
  14. Connect plug connections between main wire harness and wire harness for heater/air-conditioning unit -79 and 80-  .
    Fig 14: Identifying Electric Line
    G09831138Courtesy of PORSCHE CARS NORTH AMERICA, INC.
    1. 14.1. Lay main wire harness to heater/air-conditioning unit wire harness and fix with a tie-wrap.
    2. 14.2. Push in upper electric plug connection at heater/air-conditioning unit until it engages securely.
      Fig 15: Connecting Upper Electric Plug Connection
      G09831139Courtesy of PORSCHE CARS NORTH AMERICA, INC.
    3. 14.3. Push in lower electric plug connection at heater/air-conditioning unit until it is felt to engage.
      Fig 16: Connecting Lower Electric Plug Connection
      G09831140Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  15. Push on connector for tilt sensor control unit -77-  until it engages securely. → 966319 TILT SENSOR CONTROL UNIT - section on "Removing"
  16. Fasten ground point under the unit carrier -76-  .
    Fig 17: Securing Ground Point
    G09831141Courtesy of PORSCHE CARS NORTH AMERICA, INC.
    1. 16.1. Connect ground straps and tighten with the fastening nut. → Tightening torque: 9 Nm (6.5 ft. lb.) 
  17. Push on connector for pedal sensor -69-  until it engages securely. → WM 208019 REMOVING AND INSTALLING ACCELERATOR PEDAL (ALL MODELS) - section on "Installing" 
  18. Push on connector for brake light switch -68-  until it engages securely. → 943619 REMOVING AND INSTALLING BRAKE LIGHT SWITCH - section on "Installing".
  19. Push on connectors of KESSY/PAS control unit -66 and 67-  until they engage securely. → 966619 REMOVING AND INSTALLING KESSY CONTROL UNIT - section on "Installing"
  20. Push on connector on Gateway control unit -65-  until it engages securely. → 903519 REMOVING AND INSTALLING GATEWAY CONTROL UNIT - section on "Installing"
  21. Push together plug connection between main wire harness and wire harness for door at the left and right -59 and 60-  until they engage securely. → 973219 REMOVING AND INSTALLING WIRE HARNESS FOR DOOR  - section on "Locking"
  22. Clip in wire harness at door sill.
    Fig 18: Clipping In Wire Harness At Door Sill
    G09831142Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  23. Fasten ground point under the passenger seat -54-  .
    Fig 19: Securing Ground Point
    G09831143Courtesy of PORSCHE CARS NORTH AMERICA, INC.
    1. 23.1. Connect ground straps and tighten with the fastening nut. → Tightening torque: 9 Nm (6.5 ft. lb.) 
  24. Push on connectors for telephone control unit -50 to 53-  until they engage securely. → 919019 REMOVING AND INSTALLING CONTROL UNIT FOR TELEPHONE - section on "Installing"
    1. 24.1. Clip in wire harness for telephone control unit.
      Fig 20: Clipping In Wire Harness For Telephone Control Unit
      G09831144Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  25. Clip in wire harness under driver's seat.
    Fig 21: Clipping In Wire Harness Under Driver Seat
    G09831145Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  26. Fasten ground point under the driver's seat -49-  .
    Fig 22: Securing Ground Point
    G09831146Courtesy of PORSCHE CARS NORTH AMERICA, INC.
    1. 26.1. Connect ground straps and tighten with the fastening nut. → Tightening torque: 9 Nm (6.5 ft. lb.) 
  27. Push on connectors on control unit for rear convenience systems -46 to 48-  until they engage securely. → Installing Control Unit For Rear Convenience Systems - section on "Installing".
  28. Push on connectors on ParkAssist control unit -44 and 45-  until they engage securely. → 917419 REMOVING AND INSTALLING PARKASSIST CONTROL UNIT - section on "Installing"
  29. Push on connectors for center airbag sensor at the left and right -42 and 43-  until they engage securely. → Installing Airbag Sensor - section on "Installing"
  30. Push on connector on Tiptronic control unit -41-  until it engages securely and lock it. → 373019 REMOVING AND INSTALLING TRANSMISSION CONTROL UNIT - section on "Installing"
    1. 30.1. Clip in wire harness for Tiptronic control unit.
      Fig 23: Clipping In Wire Harness For Tiptronic Control Unit
      G09831147Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  31. Fit rubber sleeves -39 and 40-  and push on connector for front seat-belt pretensioners at the left and right -37 and 38-  . → Installing Front Three-Point Belt - section on "Installing"
  32. Connect plug connection between main wire harness and rear wire harness at the left and right -33 and 34-  and lock it.
    Fig 24: Connecting Plug Connection For Main To Rear Wire Harness
    G09831148Courtesy of PORSCHE CARS NORTH AMERICA, INC.
scientia non olet · About LEMON Manuals