Combination Meter - With Diagnostics

• Service Specifications
• Special Tools
• Diagnosis
  • Standard Flow Of Diagnostic Troubleshooting
  • Diagnosis Function
    • How To Connect The Scan Tool (M.U.T.-III)
    • How To Read And Erase Diagnostic Trouble Codes
    • Check Of Freeze Frame Data
  • Diagnostic Trouble Code Chart
  • Diagnostic Trouble Code Procedures
    • DTC B1200: Malfunction of odometer
      • Trouble Judgment
      • Troubleshooting Hints
      • Diagnosis
    • DTC U1073: Bus-off
      • Diagnostic Function
      • Trouble Judgment
      • Troubleshooting Hints
      • Diagnosis
    • DTC U1100: EV ECU CAN timeout(1)
      • Trouble Judgment
      • Technical Description (Comment)
      • Troubleshooting Hints
      • Diagnosis
    • DTC U1102: ASC/TCL/ABS timeout/Not equipped
      • Trouble Judgment
      • Technical Description (Comment)
      • Troubleshooting Hints
      • Diagnosis
    • DTC U1106: EPS CAN timeout/Not equipped
      • Trouble Judgment
      • Technical Description (Comment)
      • Troubleshooting Hints
      • Diagnosis
    • DTC U1109: ETACS CAN timeout/Not equipped
      • Trouble Judgment
      • Technical Description (Comment)
      • Troubleshooting Hints
      • Diagnosis
    • DTC U1121: T/M (CAN message)
      • Trouble Judgment
      • Technical Description (Comment)
      • Troubleshooting Hints
      • Diagnosis
    • DTC U1122: Brake module (CAN message)
      • Trouble Judgment
      • Technical Description (Comment)
      • Troubleshooting Hints
      • Diagnosis
    • DTC U1190: No receive fault detect signal
      • Trouble Judgment
      • Troubleshooting Hints
      • Diagnosis
    • DTC U1206: Instruction to sleep flag
      • Trouble Judgment
      • Technical Description (Comment)
      • Troubleshooting Hints
      • Diagnosis
  • Trouble Symptom Chart
  • Symptom Procedures
    • Inspection Procedure 1: Power supply circuit check; Inspection Procedure 2: When the reset witch is operated with the electric motor switch at OFF position, the odo/trip meter is not displayed; Inspection Procedure 3: The combination meter does not work at all when the electric motor switch is at ON position
      • Notes
      • Technical Description (Comment)
      • Troubleshooting Hints
      • Diagnosis
    • Inspection Procedure 4: The speedometer does not work (the other meters work); Inspection Procedure 5: The odometer does not work (the other meters work); Inspection Procedure 6: The tripmeter does not work (the other meters work)
      • Technical Description (Comment)
      • Troubleshooting Hints
      • Diagnosis
    • Inspection Procedure 7: The energy usage indicator does not work (the other meters work); Inspection Procedure 8: The energy level gauge does not work (the other meters work)
      • Technical Description (Comment)
      • Troubleshooting Hints
      • Diagnosis
  • Service Data
  • Actuator Test Table
  • Check At Ecu Terminals
• On-Vehicle Service
  • Speedometer Check
  • Energy Usage Indicator Inspection
  • Meter Brightness Setting
    • Notes
    • How To Set
    • Brightness Level Table
  • Service Reminder Function Set
    • How To Set By Operating The Scan Tool MB991958
    • How To Operate The Scan Tool MB991958
    • Reminder Reset (Indicator Off)
    • Next Schedule Reminder Cancel
    • Extra Reminder Setting
    • Extra Reminder Cancel
    • Periodic Reminder Schedule Set
    • Integrated Value Adjustment
    • Optional Int Schedule Setting
    • How To Set By Special Operation Of Switch
    • How To Cancel The Service Reminder Warning
    • How To Set The Schedule
    • How To Inactivate The Service Reminder Function
• Combination Meter Assembly
  • Removal And Installation
    • Notes
    • Removal Service Points
      • << A >> Combination Meter Assembly Removal
    • Installation Service Points
      • >> A << Combination Meter Assembly Installation
  • Disassembly And Assembly