Section 107 (Chassis Electrical - Lancer Evolution (3 Of 5))
WARNING: This page is about a different car, the 2008 Mitsubishi Lancer. However, it is still accessible from the selected car via links, so may be relevant.
- Radio And Cd Player
- General Information
- Special Tools
- Diagnosis
- Introduction To Audio System Diagnosis
- Standard Flow Of Diagnostic Troubleshooting
- Diagnosis Function
- Diagnostic Trouble Code Chart
- Diagnostic Trouble Code Procedures
- DTC U0019: Bus Off (Can-B)
- DTC U0141: ETACS Can Timeout
- DTC U0151: SRS-ABG Can Timeout
- DTC U0154: OCM Can Timeout
- DTC U0155: Meter Can Timeout
- DTC U0164: A/C Can Timeout
- DTC U0168: WCM Can Timeout
- DTC U0195: Satellite Radio Can Timeout
- DTC U0197: Hands Free Module Can Timeout
- DTC U1415: Coding Not Completed/Data Fail
- DTC B2420: Power Integrated Circuit
- DTC B2421: Radio Tuner
- DTC B2423: 6CD Player Error
- DTC B2424: Cd Player Error
- DTC B2450: Switch Panel Communication
- DTC B2451: Audio Panel Type Error
- Trouble Symptom Chart
- Symptom Procedures
- Inspection Procedure 1: Power Is Not Turned On When The Power Switch Is Turned On
- Inspection Procedure 2: No Sound Is Heard < Vehicles With Audio Amplifier >
- Inspection Procedure 3: No Sound Is Heard From One Of The Speakers < Vehicles Without Audio Amplifier >
- Inspection Procedure 3: No Sound Is Heard From One Of The Speakers < Vehicles With Audio Amplifier >
- Inspection Procedure 4: The Audio Does Not Operate Normally By Operating The Radio And Cd Player Of The Center Panel Unit
- Inspection Procedure 5: Audio Illuminations Does Not Work Normally
- Inspection Procedure 6: The Sound Of External Input Are Not Played
- Inspection Procedure 7: Noise Is Present While Moving (Am)
- Inspection Procedure 8: Noise Is Present While Moving (Fm)
- Inspection Procedure 9: Sound Mixed With Noise, Only At Night (Am)
- Inspection Procedure 10: Noise Is Overpowering Both Am And Fm
- Inspection Procedure 11: Excessive Noise On Am And Fm
- Inspection Procedure 12: Noise Is Detected With Engine Running
- Inspection Procedure 13: Noise Appears During Vibration Or Shocks
- Inspection Procedure 14: Noise Is Present While Moving (Fm)
- Inspection Procedure 15: Constant Noise
- Inspection Procedure 16: No Reception (Am)
- Inspection Procedure 17: Poor Reception
- Inspection Procedure 18: Distortion On Am And/Or Fm
- Inspection Procedure 19: Distortion On Fm Only
- Inspection Procedure 20: Auto Select Function Inoperative, Too Few Automatic Stations Are Selected
- Inspection Procedure 21: Preset Stations Are Erased
- Inspection Procedure 22: Cd Cannot Be Inserted
- Inspection Procedure 23: No Sound (Cd Only)
- Inspection Procedure 24: Cd Sound Skips
- Inspection Procedure 25: Sound Quality Is Poor
- Inspection Procedure 26: Cd Cannot Be Ejected
- On-Vehicle Service
- Removal And Installation
- Inspection
- MMCS
- MITSUBISHI Multi Communication System
- Special Tools
- Diagnosis
- Standard Flow Of Diagnostic Troubleshooting
- Precautions On Servicing MMCS
- Service Mode
- Diagnosis Function
- Diagnostic Trouble Code Chart
- Diagnostic Trouble Code Procedures
- DTC B2226: Can Error
- DTC B2240: Communication Error With Can Box
- DTC B2477: VIN Not Programmed
- DTC U0019: Bus Off (Can-B)
- DTC U0141: ETACS Can Timeout
- DTC U0151: SRS-AGB Can Timeout
- DTC U0154: OCM Can Timeout
- DTC U0155: Meter Can Timeout
- DTC U0164: A/C Can Timeout
- DTC U0168: WCM Can Timeout
- DTC U0195: Satellite Radio Can Timeout
- DTC U0197: Hands Free Module Can Timeout
- DTC U1415: Coding Not Completed/Data Fail
- DTC U1417: Implausible Coding Data
- Trouble Symptom Chart
- Symptom Procedures
- Inspection Procedure 1: No Navigation Screen Is Displayed
- Inspection Procedure 2: No Sound Is Heard < Vehicles With Audio Amplifier >
- Inspection Procedure 3: No Sound Is Heard From One Of The Speakers < Vehicles With Audio Amplifier >
- Inspection Procedure 4: The Navigation System Can Be Operated While The Vehicle Is Driven
- Inspection Procedure 5: The Screen Is Not Normal In The Navigation Mode (The Own Vehicle Mark Is Dislocated)
- Inspection Procedure 6: Poor Reception
- Inspection Procedure 7: GPS Signal Can Not Be Received
- Inspection Procedure 8: Cd (Compact Disk)/DVD (Video Disk) Cannot Be Played
- Inspection Procedure 9: Image Of A DVD (Video Disk) Is Played, But No Sound Is Played
- Inspection Procedure 10: Sound Of A DVD (Video Disk) Can Be Played, But No Image Is Played
- Inspection Procedure 11: The Picture And Sound Of External Input Are Not Played
- Inspection Procedure 12: Check The Can Box Unit Power Supply Circuit
- ETACS Function Customization Function
- Removal And Installation
- Inspection