LEMON Manuals: Even more car manuals for everyone
Home >> Mercedes Benz >> 2025 >> GLA250 Base >> Repair and Diagnosis >> External Pages >> Different car >> Section 24 (Windows -- 118 Chassis) >> Testing & Repair >> Adjust Rear Door Side Window - AR67.30-P-0016MFC

Adjust Rear Door Side Window - AR67.30-P-0016MFC

WARNING: This page does not describe the selected car, but rather 12 other vehicles, including the 2023 Mercedes-Benz CLA45 AMG, 2023 Mercedes-Benz CLA35 AMG, 2023 Mercedes-Benz CLA250, 2022 Mercedes-Benz CLA45 AMG, and 2022 Mercedes-Benz CLA35 AMG. However, it is still accessible from the selected car via links, so may be relevant.

Model 118.3/6 

Shown on model 118.3 

G16063782Courtesy of MERCEDES-BENZ USA
INSPECT Check     
1 Check rear door adjustment. IMPORTANT A correct adjustment of the rear door is the prerequisite for the adjustment of the rear door side window (1). AR72.12-P-0650MFC
2 Affix tapes (arrows), as shown, so that they are flush with upper edge of rear door side window (1). IMPORTANT Attach tapes (arrows) as far apart as possible.  
3 Fully lower rear door side window (1) and then raise again to top end position.    
4 Close rear door.    
5 Apply markings to tapes (arrows) at lower edge of roof paneling. NOTES
Ensure that roof frame seal is not pressed in during application of markings.
An incorrect window guide depth will otherwise be determined.		  
6 Determine dimension (b). IMPORTANT Determine dimension (b) at two locations that are as far apart as possible. A taper of dimension (b) of max. 1 mm is permitted from top to bottom.  
7 Determine dimension (c). IMPORTANT Determine dimension (c) at two points at large distance if possible.  
8 Determine dimension (e).    
9 Open rear door.    
10 Determine dimensions (a).    
11 Lock door lock of the rear door with a suitable tool. IMPORTANT The rear door side window (1) is thus raised to topmost position.  
12 Determine dimension (d).    
13 Unlock rear door lock by actuating inside door handle.    
14 Compare dimensions (a, b, c, d, e) with specified values. IMPORTANT Note deviations between actual and specified values.
Insertion depth of rear door side window in roof edge		 *BE67.30-P-1004-03E 
    Distance between rear door side window and B-pillar cover *BE67.30-P-1005-03E 
    Transition between rear door side window and B-pillar cover *BE67.30-P-1006-03E 
    Transition between upper edge of rear door/front door side window and upper edge of triangular window *BE67.30-P-1007-03E 
    Transition between rear door/front door side window and trim element *BE67.30-P-1008-03E 
  Adjust rear door side window (1) in X-direction (X)     
15 Remove door trim.   AR72.12-P-1011MFA
16 Adjust distance between the rear door side window (1) and the B-pillar cover (4). IMPORTANT Observe previously noted deviations. AR67.30-P-0016-03MFC 
    Distance between rear door side window and B-pillar cover *BE67.30-P-1005-03E 
    SPECIAL TOOL Feeler gauge Fig 1
  Adjust rear door side window (1) in Y-direction (Y)     
17 Adjust transition between the rear door side window (1) and B-pillar cover (4).   AR67.30-P-0016-02MFC 
    Transition between rear door side window and B-pillar cover *BE67.30-P-1006-03E 
    SPECIAL TOOL Socket wrench Fig 2
    SPECIAL TOOL Socket Fig 3
  Adjust rear door side window (1) in Z-direction (Z)     
18 Remove outer sealing rail (3).    
19 Adjust window guide depth of the rear door side window (1) in the roof frame seal. IMPORTANT Observe previously noted deviations. AR67.30-P-0016-01MFC 
    Insertion depth of rear door side window in roof edge *BE67.30-P-1004-03E 
    Distance between rear door side window and B-pillar cover *BE67.30-P-1005-03E 
    SPECIAL TOOL Feeler gauge Fig 1
  Adjust rear door triangular window (2) in Y-direction (Y) and Z-direction (Z)     
20 Adjust rear door triangular window (2). IMPORTANT Observe previously noted deviations. AR67.30-P-0016-04MFC 
    Transition between upper edge of rear door/front door side window and upper edge of triangular window *BE67.30-P-1007-03E 
    Transition between rear door/front door side window and trim element *BE67.30-P-1008-03E 
    SPECIAL TOOL Socket wrench Fig 4
    SPECIAL TOOL Feeler gauge Fig 1
INSTALLING Install     
21 Install outer sealing rail (3). IMPORTANT When adjusting the rear door side window (1) in Z-direction (Z).  
22 Install door trim. IMPORTANT When adjusting rear door side window (1) in X-direction (X). AR72.12-P-1011MFA
23 Remove tapes (arrows).    
24 Normalize rear door side window (1).    
SIDE WINDOW(S)

Number Designation Model 118
BE67.30-P-1004-03E Insertion depth of rear door side window in roof edge Dimension "a" mm 4, 7 (±1)
SIDE WINDOW(S)

Number Designation Model 118
BE67.30-P-1005-03E Distance between rear door side window and B-pillar cover Dimension "b" mm 10 (±1)
SIDE WINDOW(S)

Number Designation Model 118
BE67.30-P-1006-03E Transition between rear door side window and B-pillar cover Dimension "c" mm 0, 5 (+1/-0, 5)
SIDE WINDOW(S)

Number Designation Model 118
BE67.30-P-1007-03E Transition between upper edge of rear door/front door side window and upper edge of triangular window Dimension "D" mm 0 (-1)
SIDE WINDOW(S)

Number Designation Model 118
BE67.30-P-1008-03E Transition between rear door/front door side window and trim element Dimension "E" mm 8 (±1)
Fig 1: Identifying Feeler Gauge (129 589 03 21 00)
G07699374Courtesy of MERCEDES-BENZ USA
Fig 2: Identifying Socket Wrench (209 589 00 09 00)
G11129151Courtesy of MERCEDES-BENZ USA
Fig 3: Identifying Socket (209 589 00 09 03)
G11065760Courtesy of MERCEDES-BENZ USA
Fig 4: Identifying Socket Wrench (219 589 00 09 00)
G14549374Courtesy of MERCEDES-BENZ USA
scientia non olet · About LEMON Manuals