LEMON Manuals: Even more car manuals for everyone
Home >> Mercedes Benz >> 2017 >> GT AMG >> Repair and Diagnosis >> Suspension >> Electronic Suspension >> Suspension -- 190 Chassis >> Testing & Repair >> Remove/Install Rear Suspension Strut >> Remove/Install Rear Suspension Strut - AR32.25-P-1016RGM

Remove/Install Rear Suspension Strut - AR32.25-P-1016RGM

Model 190 

With Code 478 (AMG RIDE CONTROL) 

Fig 1: Rear Suspension Strut Components Location - Model 190 With Code 478
G16677653Courtesy of MERCEDES-BENZ USA
G16677654Courtesy of MERCEDES-BENZ USA
WARNING Risk of injury.  Moving parts can pinch, crush or, in extreme cases even sever extremities. No parts of the body or limbs should be within the operating area of mechanical components when moving components. AS00.00-Z-0009-01A
Notice  Notes on handling, transport and storage of ceramic brake disks   AH42.10-P-9406-13A
Notice  Notes on self-locking nuts and bolts   AH00.00-P-0001-01KOA
Notice  Notes on threaded connections fastened using a tightening angle-based tightening process   AH00.00-P-0020-01A
  Notes on safety-relevant components   AH00.00-Z-0019-01A
  Notes on repair work on suspension components   AH00.00-P-0100-01A
REMOVINGINSTALLING Remove/install     
1 Remove center trim in trunk. Model 190.3
with code 478 (AMG RIDE CONTROL)
AR68.30-P-4810RG
2 Remove cover panel (11).    
3 Remove setting shaft for rebound stage on rear suspension strut.   AR32.25-P-0002RG 
4 Remove roll bar. Model 190 with code 478 (AMG RIDE CONTROL)
with code B25 (AMG Track Package)
 
5 Remove corresponding rear wheel.   AR40.10-P-1100RQ
6 Remove torsion bar linkage (3) from lever arm or stabilizer bar.   AR32.35-P-3329RG 
7 Remove nut of bolt (4). IMPORTANT Because of the tensions involved the bolt (4) should be removed at a later stage.  
    TORQUE SPECIFICATION Nut, rear suspension strut to wheel carrier/mounting support *BA32.25-P-1004-04H 
8 Unscrew nut of bolt (5) and remove bolt (5). TORQUE SPECIFICATION Nut, lower transverse control arm to wheel carrier *BA35.20-P-1003-07D 
9 Remove nuts (2). TORQUE SPECIFICATION Nut, suspension strut at rear to body *BA32.25-P-1003-04H 
10 Remove bolt (4).    
11 Loosen and remove suspension strut (1). IMPORTANT Do not disassemble suspension strut (1). If this is however necessary, always replace suspension struts (1) in pairs.  
12 Install in the reverse order.    
MEASURING Measure     
13 Perform chassis alignment.   AR40.20-P-0200RQ
SUSPENSION STRUTS

Number Designation Model 190 with code 479 (AMG RIDE CONTROL sports suspension) Model 190 with code 478 (AMG RIDE CONTROL) Model 190 with code 486 (Sports suspension)
BA32.25-P-1003-04H Nut, suspension strut at rear to body Stage 1 Nm 35 35
Stage 2 Nm - -
SUSPENSION STRUTS

Number Designation Model 190 with code 479 (AMG RIDE CONTROL sports suspension) Model 190 with code 478 (AMG RIDE CONTROL) Model 190 with code 486 (Sports suspension)
BA32.25-P-1004-04H Nut, rear suspension strut to wheel carrier/mounting support Stage 1 Nm 80 80
Stage 2 ∠° 120 120
WHEEL CONTROL

Number Designation Model 190
BA35.20-P-1003-07D Nut, lower transverse control arm to wheel carrier Stage 1 Nm 70
Stage 2 ∠° 120