Retrofit B-Pillar Reinforcement In Area Of Lock Striker - SM63.20-D-0009A
Model 906.1
| Risk of injury caused by scraping or cutting body parts on sharp vehicle parts | Always wear protective gloves when working on or near sharp and non-deburred vehicle parts. Deburr repair panels. |
AS00.00-Z-0017-01A | |
| General information on body repair | AH60.00-N-0001-01A | ||
| Remove | |||
| 1 | Remove driver seat | ||
| AR91.10-D-1010H | |||
| 2.1 | Remove passenger seat | Model 906.1 except code S23 (Co-driver's seat double seat) |
|
| 2.2 | Remove passenger bench seat | Model 906.1 with code S23 (Co-driver's seat double seat) |
|
| Model 906.1 with code S23 (Co-driver's seat double seat) |
AR91.10-D-1035A | ||
| 3 | Remove seat belt with emergency tensioning retractor on driver and passenger side | ||
| AR91.40-D-0630B | |||
| 4 | Remove lock striker on B-pillars on driver and passenger side | ||
| 5 | Cover all detachable parts remaining in vehicle with welding protection blankets | ||
| 6 | Drill out ends of cracks (arrows) in B-pillar panel with Ø 3 mm drill bit | If a crack is present. | |
| 7 | Prepare B-pillar reinforcement (1) and panel of B-pillar in area of lock striker on driver and passenger side | SM63.20-D-0009-01A | |
| Install | |||
| The high voltage used for electric welding presents a lethal hazard. Risk of explosion from welding in areas close to highly inflammable materials. Risk of injury from weld splatter and UV-light when welding. Risk of poisoning from inhaling welding gases | Use insulating mats. Wear protective clothing, safety glasses and a protective mask. Remove highly flammable materials from the hazard area. Use air extraction system. | AS00.00-Z-0007-01A | |
| Risk of poisoning caused by inhaling vapors or swallowing adhesive. Risk of injury caused by adhesive coming into contact with skin and eyes | Wear respiratory protection, protective gloves and safety glasses. Pour adhesive into suitable and appropriately marked containers only. | AS00.00-Z-0016-01A | |
| Risk of explosion caused by paint vapors igniting. Risk of poisoning caused by inhaling paint vapors. | No smoking! No open fire! Use respiratory protection, protective clothing, gloves, safety glasses and protective skin cream. Ensure that the area is well ventilated. | AS98.00-Z-0002-01A | |
| Measures for preventing damage to vehicles or components when performing electric welding work | AH00.00-N-0005-01A | ||
| 8 | Install B-pillar reinforcement (1) on driver and passenger side | SM63.20-D-0009-02A | |
| 9 | Remove welding protection blankets | ||
| 10 | Clean repair areas | ||
| 11 | Prime repair area using primer filler | http://portal.aftersales.i.daimler.com |
|
| 12 | Paint repair areas and adjacent surfaces | http://portal.aftersales.i.daimler.com |
|
| 13 | Apply additional cavity preservation | ||
| AR97.20-D-1500H | |||
| 14 | Install lock striker on B-pillars on driver and passenger side | ||
| 15 | Adjust lock striker on driver and passenger side | ||
| AR72.15-D-1021-02B | |||
| *BA72.15-N-1013-01C | |||
| 16 | Install seat belt with emergency tensioning retractor on driver and passenger side | ||
| AR91.40-D-0630B | |||
| 17.1 | Install front passenger bench seat | Model 906.1 with code S23 (Co-driver's seat double seat) |
|
| AR91.10-D-1035A | |||
| 17.2 | Install front passenger seat | Model 906.1 except code S23 (Co-driver's seat double seat) |
|
| 18 | Install driver seat | ||
| AR91.10-D-1010H |
HINGED DOORS
| Number | Designation | Model 906.1/6/7 | |
|---|---|---|---|
| BA72.15-N-1013-01C | Bolt, lock striker to B-pillar | Nm | 20 |
PARTS ORDERING NOTE
| Part no. | Designation | Quantity |
|---|---|---|
| A 906 650 12 00 | Bonding kit | 1 |
| N 914031 005208 | Bolt | 4 |
| A 012 989 29 71 | Basic putty | 1 |
| A 906 637 50 00 | B-pillar reinforcement | 2 |