Partially replace outside section of longitudinal member - AR63.30-P-1050P
MODEL 203.0 /2
| Remove | |||
| Risk of injury caused by scraping or cutting body parts on sharp vehicle parts | Always wear protective gloves when working on or near sharp and untrimmed vehicle parts. Deburr metal repairs. |
AS00.00-Z-0017-01A | |
| Risk of death. Death may result if vehicle slips or topples from the lifting platform. | Align vehicle between columns of lifting platform and position the four support plates below support points specified by vehicle manufacturer. | AS00.00-Z-0010-01A | |
| Risk of death caused by high voltage used for arc welding. Risk of explosion caused by welding in the area of high combustible materials. Risk of injury caused by welding spatter and UV-light while welding. Risk of poisoning caused by inhaling welding vapors. | Use insulating mats. Wear protective clothing, safety glasses, and protective mask. Remove highly inflammable materials from the danger zone. Use air extractor. | AS00.00-Z-0007-01A | |
| General information on repairs to body | All models | AH60.00-N-0001-01A | |
| Measures for preventing damage to vehicles or components when performing arc welding work | All models | AH00.00-N-0005-01A | |
| Notes on paintwork repairs | All models | AH98.00-P-9408-02A | |
| 1 | Remove rear door | AR72.12-P-0600P | |
| 2 | Remove detachable body components in area to be repaired | ||
| 3 | Cover all detachable body components remaining in vehicle (area to be repaired) | Tarpaulin (fireproof) | *WH58.30-Z-1001-40A |
| 4 | Separate outer side longitudinal member | AR63.30-P-1050-01P | |
| Figure | |||
| Figure | |||
| *WH58.30-Z-1002-01A | |||
| *WH58.30-Z-1006-01A | |||
| *WH58.30-Z-1001-03A | |||
| *WH58.30-Z-1024-04A | |||
| *WH58.30-Z-1021-04A | |||
| Drill (electric/pneumatic) | *WE58.40-Z-1001-03A | ||
| Straight grinder (electric/pneumatic) | *WE58.40-Z-1002-03A | ||
| Angular grinder (electric/pneumatic) | *WE58.40-Z-1003-03A | ||
| Body saw (electric/pneumatic) | *WE58.40-Z-1004-03A | ||
| Wet/dry vacuum cleaner | *WE58.40-Z-1005-03A | ||
| Zinc dust paint suitable for spot welding | *BR00.45-Z-1001-07A | ||
| 5 | Preparing outer side longitudinal member | AR63.30-P-1050-02P | |
| Figure | |||
| *WH58.30-Z-1001-03A | |||
| *WH58.30-Z-1024-04A | |||
| Drill (electric/pneumatic) | *WE58.40-Z-1001-03A | ||
| Angular grinder (electric/pneumatic) | *WE58.40-Z-1003-03A | ||
| Body saw (electric/pneumatic) | *WE58.40-Z-1004-03A | ||
| Zinc dust paint suitable for spot welding | *BR00.45-Z-1001-07A | ||
| Install | |||
| 6 | Install outer side longitudinal member and weld in | AR63.30-P-1050-03P | |
| *WH58.30-Z-1001-03A | |||
| *WH58.30-Z-1003-01A | |||
| *WH58.30-Z-1003-02A | |||
| AH60.00-P-0003-01N | |||
| *WE58.40-Z-1003-14A | |||
| *WH58.30-Z-1003-29A | |||
| *WH58.30-Z-1024-04A | |||
| *WH58.30-Z-1021-04A | |||
| *WH58.30-Z-1038-02A | |||
| Rivet | *BR00.45-Z-1001-13A | ||
| Inert gas welder | *WE58.40-Z-1001-02A | ||
| Spot welder | *WE58.40-Z-1002-02A | ||
| Straight grinder (electric/pneumatic) | *WE58.40-Z-1002-03A | ||
| Drill (electric/pneumatic) | *WE58.40-Z-1001-03A | ||
| Angular grinder (electric/pneumatic) | *WE58.40-Z-1003-03A | ||
| Wet/dry vacuum cleaner | *WE58.40-Z-1005-03A | ||
| Zinc dust paint suitable for spot welding | *BR00.45-Z-1001-07A | ||
| MB body sealant for sealing seams (suitable for painting/310ml cartridge) | *BR00.45-Z-1003-01A | ||
| MB preservative | *BR00.45-Z-1003-05A | ||
| 7 | Clean areas repaired and prime with primer / filler | ||
| 8 | Seam sealing following repair | AR97.10-P-4000P | |
| Sealant | *BR00.45-Z-1003-01A | ||
| Seam sealant, sprayable 310 ml | *BR00.45-Z-1041-01A | ||
| 9 | Paint outer side longitudinal member and adjacent surfaces | ||
| 10 | Supplement hollow cavity preservation | AP97.20-P-0640-01A | |
| Notes on hollow cavity preservation | Model 203 | AH97.20-P-0001-01B | |
| 11 | Install electric lines and vacuum lines in repair area | ||
| 12 | Install rear door | AR72.12-P-0600P | |
| 13 | Install all removed detachable body components |
COMMERCIALLY AVAILABLE TOOLS
| Number | Designation |
|---|---|
| WH58.30-Z-1002-01A | Ball cutter, dia. 12 mm |
| WH58.30-Z-1003-01A | Electrode miller |
| WH58.30-Z-1006-01A | Vario Drill WS 91 spot weld removing tool |
| WH58.30-Z-1003-02A | Clamping pliers |
| WH58.30-Z-1038-02 | Manual temporary fastener, dia.6.4 mm - clamping range 0 -15 mm, identification color silver Firma Hausmann GmbH D-34346 Hann. Munden, Germany |
| WH58.30-Z-1001-03A | Round wire brush, braided, dia. 70 mm |
| WH58.30-Z-1021-04A | Cutting disk, dia. 65 mm, 80 m/s (max. 23,500 rpm) |
| WH58.30-Z-1024-04A | Abrasive disk, dia. 115 mm, 80 m/s (max. 13,250 rpm) |
| WH58.30-Z-1003-29A | Hand riveter |
| WH58.30-Z-1001-40A | Tarp (fire-resistant) |
WORKSHOP EQUIPMENT
| WE58.40-Z-1001-02A | Inert gas welder |
| WE58.40-Z-1002-02A | Spot welder |
| WE58.40-Z-1001-03A | Drill (electric/pneumatic) |
| WE58.40-Z-1002-03A | Straight grinder (electric/pneumatic) |
| WE58.40-Z-1003-03A | Angle grinder (electric/pneumatic) |
| WE58.40-Z-1004-03A | Body saw (electric/pneumatic) |
| WE58.40-Z-1005-03A | Wet/dry vacuum cleaner |
| WE58.40-Z-1003-14A | Blind rivet tool |
REPAIR MATERIALS
| Number | Designation | Order number |
|---|---|---|
| BR00.45-Z-1003-01A | Sealant | A 001 989 63 20 |
| BR00.45-Z-1041-01A | Seam sealant, sprayable 310 ml | A 002 989 84 20 |
| BR00.45-Z-1003-05A | Preservation agent | A 000 986 72 70 05 |
| BR00.45-Z-1001-07A | Zinc dust paint suitable for spot welding | A 000 986 34 42 |
| BR00.45-Z-1001-13A | Rivet | A 003 990 35 97 |