Removing and installing throttle control cable - AR30.10-P-3400EA

ENGINE 119.982 in MODEL 129.067

ENGINE 120.983 in MODEL 129.076

ENGINE 119.981 in MODEL 140.042 /043 /063

ENGINE 120.982 in MODEL 140.056 /057 /076

ENGINE 606.961 in MODEL 140.135

ENGINE 111.943 in MODEL 170.445

ENGINE 111.973 in MODEL 170.447

ENGINE 111.944 as of 1.9.96 in MODEL 202.025 /082

ENGINE 111.975 as of 1.9.96 in MODEL 202.024/085

ENGINE 112.910 in MODEL 202.026 /086

ENGINE 112.920 in MODEL 202.029 /089

ENGINE 111.944 in MODEL 208.345

ENGINE 111.975 in MODEL 208.347

ENGINE 112.940 in MODEL 208.365 /465

ENGINE 112.921 in MODEL 210.063 /263 /081 /281

ENGINE 112.941 in MODEL 210.065 /082 /265 /282

ENGINE 113.940 in MODEL 210.070 /270

ENGINE 119.985 in MODEL 210.072 /272

ENGINE 111.947 in MODEL 210.045 /245

ENGINE 112.923 in MODEL 129.059

ENGINE 112.943 in MODEL 129.064

ENGINE 113.961 in MODEL 129.068

ENGINE 113.980 in MODEL 210.074/274

ENGINE 113.944 in MODEL 202.033/093

ENGINE 113.943 in MODEL 208.370 /470

ENGINE 113.984 in MODEL 208.374

Shown on model 140

Fig 1: Identifying Throttle Control Cable Components (Shown On Model 140)

Courtesy of MERCEDES-BENZ OF NORTH AMERICA.

Shown on model 210

Fig 2: Identifying Throttle Control Cable Components (Shown On Model 210)

Courtesy of MERCEDES-BENZ OF NORTH AMERICA.

	Removing, installing
1	Disconnect accelerator control cable (30) at ball head
2	Compress plastic clip (30/4) and pull out of fixed lever (10) together with accelerator control cable
3	Remove footwell trim
4.1	Release accelerator control cable mount (arrow) at accelerator pedal lever (33)	On engine 111.943/944/973/975, 112.921/941, 119.981/982/985, 120.982/983, 606.961: ↓ Remove bracket (37) for this purpose.
5	Push accelerator control cable (30) to the outside from inside the car	Do not press out rubber grommet (30/6).
6	Take out accelerator control cable (30) completely, working from the engine compartment	Potentiometer relay lever (31/1) with spring. At WOT stop the accelerator pedal lever travel is enlarged by the spring being compressed. This makes it possible to operate the kickdown switch.
7	Install in the reverse order
8	Check accelerator control, adjust	Engine 111.944/975 up to 31.08.96 Engine 111.943/973/947 Engine 111.944/975 as of 01.09.96 Engine 112.910/920/921/940/941/943: ↓	AR30.10-P-1010D
		manual transmission	AR30.10-P-1010C
		automatic transmission	AR30.10-P-1010CA
		Engine 113.943/944/984: ↓
		automatic transmission Engine 112.923: ↓	AR30.10-P-1010CA
		manual transmission Engine 112.923/943 Engine 113.940/961/980: ↓	AR30.10-P-1010C
		automatic transmission	AR30.10-P-1010BA
		Engine 119.981/982/985	AR30.10-P-1010EC
		Engine 120.982/983	AR30.10-P-1010FA
		Engine 606.961	AR30.10-P-1010HC