LEMON Manuals: Even more car manuals for everyone
Home >> Mazda >> 2024 >> CX-30 Preferred >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 18 (Automatic Transaxle (Service Information) - GW6AX-El) >> Oil Pressure Switch Removal/Installation [GW6AX-El] >> Oil Pressure Switch B

Oil Pressure Switch B

WARNING: This page is about a different variant/trim than selected.
  1. Disconnect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION .)
  2. Remove the front under cover No. 1. (See FRONT UNDER COVER No. 1 REMOVAL/INSTALLATION .)
  3. Remove the front under cover No. 2. (See FRONT UNDER COVER No. 2 REMOVAL/INSTALLATION .)
  4. Clean the transaxle exterior throughout with a steam cleaner or cleaning solvents.
  5. Drain the ATF. (See AUTOMATIC TRANSAXLE FLUID (ATF) REPLACEMENT [GW6AX-EL] .)
  6. Remove the oil pan.
  7. Remove the oil strainer. (See CONTROL VALVE BODY REMOVAL/INSTALLATION [GW6AX-EL] .)
  8. Remove the oil strainer O-ring. (See CONTROL VALVE BODY REMOVAL/INSTALLATION [GW6AX-EL] .)
  9. Insert a precision flathead screwdriver and move it in the direction of the arrow to disconnect the oil pressure switch B connector as shown in the figure.
    G16374972Courtesy of MAZDA MOTORS CORP.
    CAUTION:
    • Do not scratch the oil pressure switch B and oil pressure switch connector B with the precision flathead screwdriver.
    • When disconnecting connectors, grasp the connectors, not the wiring harnesses. Otherwise, the wiring harnesses may be pulled out of the connector causing poor contact.
  10. Remove the oil pressure switch B.
    G16374973Courtesy of MAZDA MOTORS CORP.
  11. Install the oil pressure switch B.
    Fig 1: Oil Pressure Switch B And Bolt With Torque Specification
    G16374974Courtesy of MAZDA MOTORS CORP.
  12. Connect the oil pressure switch B connector.
    G16374975Courtesy of MAZDA MOTORS CORP.
  13. Install the new oil strainer O-ring. (See CONTROL VALVE BODY REMOVAL/INSTALLATION [GW6AX-EL] .)
  14. Install the new oil strainer. (See CONTROL VALVE BODY REMOVAL/INSTALLATION [GW6AX-EL] .)
  15. Apply a light coat of silicon sealant (TB1217E or equivalent) to the contact surfaces of the oil pan and transaxle case.
    G16374976Courtesy of MAZDA MOTORS CORP.
    CAUTION:
    • Clean any remaining silicone sealant on the contact surface of the transaxle case and oil pan, and degrease the sealant area. Otherwise, oil could leak.
  16. Install the oil pan with new bolts before the applied sealant starts to harden.
    Fig 2: Oil Pan Bolts With Torque Specification
    G16374977Courtesy of MAZDA MOTORS CORP.
  17. Add the ATF. (See AUTOMATIC TRANSAXLE FLUID (ATF) REPLACEMENT [GW6AX-EL] .)
  18. Install the front under cover No. 2. (See FRONT UNDER COVER No. 2 REMOVAL/INSTALLATION .)
  19. Install the front under cover No. 1. (See FRONT UNDER COVER No. 1 REMOVAL/INSTALLATION .)
  20. Connect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION .)
  21. Perform the "Initial Learning" (Oil pressure switch B replacement). (See INITIAL LEARNING [GW6AX-EL] .)
  22. Perform the "Mechanical System Test". (See MECHANICAL SYSTEM TEST [GW6AX-EL] .)
scientia non olet · About LEMON Manuals