Installation [03/2017 - 05/2023]: Procedure

WARNING: This page does not describe the selected car, but rather 7 other vehicles, including the 2024 Lexus LC 500, 2023 Lexus LC 500, 2022 Lexus LC 500, 2021 Lexus LC 500, and 2020 Lexus LC 500. However, it is still accessible from the selected car via links, so may be relevant.

INSTALL FRONT SEAT BELT RETRACTOR COVER LH

Slide in the installation direction (1) shown in the illustration to attach the guide.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

	Install in this Direction (1)
	Install in this Direction (2)

Push in the installation direction (2) shown in the illustration to attach the claw and install the front seat belt retractor cover LH.

INSPECT FRONT SEAT OUTER BELT ASSEMBLY LH
See step 1

INSTALL FRONT SEAT OUTER BELT ASSEMBLY LH

Attach the guides and temporarily install the front seat outer belt assembly LH.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Install the 2 bolts.
Bolt A

Torque: 12.5 N.m (127 kgf/cm, 9 ft.lbf)

Bolt B

Torque: 42 N.m (428 kgf/cm, 31 ft.lbf)

Connect the pretensioner connector and lock the locking button as shown in the illustration.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

*a	Locking Button
*b	Lock

NOTE:

When handling the pretensioner connector, take care not to damage the pretensioner wire harness.
Securely lock the locking button.

Connect the tension reducer connector.

Install the shoulder anchor of the front seat outer belt assembly LH with the bolt.

Torque: 42 N.m (428 kgf/cm, 31 ft.lbf)

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

INSTALL CENTER PILLAR GARNISH ASSEMBLY LH
Refer to PROCEDURE - Step 17
INSTALL QUARTER TRIM PANEL ASSEMBLY LH
Refer to PROCEDURE - Step 19

INSTALL FRONT SEAT OUTER BELT ASSEMBLY LH (FLOOR ANCHOR)

Install the floor anchor of the front seat outer belt assembly LH with the bolt.

Torque: 42 N.m (428 kgf/cm, 31 ft.lbf)

*a	Tongue Plate
*b	Floor Anchor

NOTE:

When connecting the floor anchor of the front seat outer belt assembly LH, make sure that the tongue plate is facing the front of the vehicle.

Check that the ELR locks.
1. With the front seat outer belt assembly installed to the vehicle, check that the belt locks when it is pulled out quickly.

INSTALL OUTER LAP BELT ANCHOR COVER

Slide in the installation direction (1) shown in the illustration to attach the guide B.

*a	Guide A
*b	Guide B
	Install in this Direction (1)
	Install in this Direction (2)

Push in the installation direction (2) shown in the illustration to attach the guide A and install the outer lap belt anchor cover.

INSTALL FRONT DOOR SCUFF PLATE LH
Refer to PROCEDURE - Step 35 [03/2017 - 06/2019] , or refer to PROCEDURE - Step 35 [06/2019 - 04/2020] , or refer to PROCEDURE - Step 35 [04/2020 - 05/2023]
INSTALL REAR NO. 1 SEAT INNER BELT ASSEMBLY LH
See step 1
INSTALL QUARTER INSIDE TRIM BOARD LH
Refer to PROCEDURE - Step 23
INSTALL REAR SEATBACK ASSEMBLY LH
Refer to PROCEDURE - Step 1
INSTALL REAR SEATBACK COVER
Refer to PROCEDURE - Step 3
INSTALL REAR SEAT SIDE GARNISH
Refer to PROCEDURE - Step 7
INSTALL REAR SEAT CUSHION LOCK HOOK
Refer to PROCEDURE - Step 6
INSTALL REAR SEAT CUSHION ASSEMBLY
Refer to PROCEDURE - Step 7
INSTALL FRONT SEAT ASSEMBLY LH
Refer to INSTALLATION [03/2017 - 04/2020] , or refer to INSTALLATION [04/2020 - 05/2023]
INITIALIZATION OF SEAT ECU
Refer to PROCEDURE - Step 2
PERFORM ZERO POINT CALIBRATION AND SENSITIVITY CHECK (for Front Passenger Seat)
Refer to INITIALIZATION [03/2017 - ]
INSPECT SEAT BELT WARNING SYSTEM
Refer to ON-VEHICLE INSPECTION [03/2017 - 04/2020] , or refer to ON-VEHICLE INSPECTION [04/2020 - 05/2023]
INSPECT SRS WARNING LIGHT
Refer to OPERATION CHECK [03/2017 - 04/2020] , or refer to OPERATION CHECK [04/2020 - ]