LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2023 >> LC 500h >> Repair and Diagnosis >> External Pages >> Different car >> Section 22 (Supplemental Restraint System - Service Information (Coupe) (1 Of 2)) >> KNEE AIRBAG ASSEMBLY (for Front Passenger Side) >> Installation [05/2023 - ] >> Procedure

Installation [05/2023 - ]: Procedure

WARNING: This page does not describe the selected car, but rather 7 other vehicles, including the 2024 Lexus LC 500, 2023 Lexus LC 500, 2022 Lexus LC 500, 2021 Lexus LC 500, and 2020 Lexus LC 500. However, it is still accessible from the selected car via links, so may be relevant.
  1. INSTALL LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY 
    1. Check that the engine switch is off.
    2. Check that the cable is disconnected from the negative (-) battery terminal.
      WARNING:
      • Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
      • If the airbag deploys for any reason, it may cause a serious accident.
      GTY581108Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Connect the airbag connector and push the lock button to the lower No. 2 instrument panel airbag assembly.
      GTY815498Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Lock Button
      Push
      NOTE:
      • When connecting any airbag connector, take care not to damage the airbag wire harness.
      • Make sure the lock button is securely locked.
    4. Attach the claw to install the lower No. 2 instrument panel airbag assembly.
      GTY819613Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Install in this Direction
    5. Install the 3 bolts.

      Torque: 10 N.m (102 kgf/cm, 7 ft.lbf) 

      GTY787122Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  2. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 6

  3. INSTALL BOX PANEL SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 7

  4. INSTALL UPPER CONSOLE BOX 

    Refer to PROCEDURE - Step 6

  5. INSTALL SHIFTING HOLE COVER ASSEMBLY 

    Refer to PROCEDURE - Step 9

  6. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 1

  7. INSTALL RADIO REMOTE TUNING SWITCH ASSEMBLY 

    Refer to PROCEDURE - Step 11

  8. INSTALL CONSOLE PLATE 

    Refer to PROCEDURE - Step 12

  9. INSTALL NO. 2 GLOVE COMPARTMENT PANEL 

    Refer to PROCEDURE - Step 18

  10. INSTALL NO. 1 GLOVE COMPARTMENT PANEL 

    Refer to PROCEDURE - Step 34

  11. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 35

  12. INSTALL FRONT DOOR NO. 2 OPENING TRIM COVER RH 

    Refer to PROCEDURE - Step 37

  13. INSTALL FRONT DOOR OPENING TRIM COVER RH 

    HINT: 

    Use the same procedure for the RH side and LH side.

    Refer to PROCEDURE - Step 38

  14. INSTALL FRONT DOOR SCUFF PLATE RH 

    HINT: 

    Use the same procedure for the RH side and LH side.

    Refer to PROCEDURE - Step 40

  15. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL 

    Refer to PROCEDURE - Step 2

  16. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL 

    HINT: 

    When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

    Refer to AUTOMATIC LEARNING CHART [05/2023 - ]

  17. INSTALL NO. 2 DECK BOARD 

    Refer to PROCEDURE - Step 13

  18. PERFORM DIAGNOSTIC SYSTEM CHECK 

    Refer to DTC CHECK / CLEAR [04/2020 - ]

  19. CHECK SRS WARNING LIGHT 

    Refer to OPERATION CHECK [04/2020 - ]

scientia non olet · About LEMON Manuals