LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2023 >> LC 500h >> Repair and Diagnosis >> External Pages >> Different car >> Section 130 (Heating / Air Conditioning System - Service Information (Coupe) (3 Of 3)) >> Air Conditioning Panel >> Installation [05/2023 - ] >> Procedure

Installation [05/2023 - ]: Procedure

WARNING: This page does not describe the selected car, but rather 7 other vehicles, including the 2024 Lexus LC 500, 2023 Lexus LC 500, 2022 Lexus LC 500, 2021 Lexus LC 500, and 2020 Lexus LC 500. However, it is still accessible from the selected car via links, so may be relevant.
  1. INSTALL INTEGRATION CONTROL AND PANEL ASSEMBLY 
    1. Connect the 3 connectors.
      GTY829544Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Attach the clamp.
    3. Attach the claw and clip to install the integration control and panel assembly.
      GTY785168Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  2. INSTALL NO. 1 INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 26

  3. INSTALL HOOD LOCK CONTROL LEVER SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 27

  4. INSTALL NO. 1 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 28

  5. INSTALL NO. 2 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 29

  6. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY 
    1. Move the upper console panel sub-assembly to the installation position diagonally at a slightly slanted angle from the rear upper of the vehicle.
      GTY793487Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Place Hands Here
      Install in this Direction (1)
      Install in this Direction (2)
      NOTE:

      Hold the areas shown in the illustration, lift the upper console panel sub-assembly and while inserting a portion of the claw into the mating hole move it to the installation position.

    2. Attach the claw.
      GTY817893Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Attach the claw.
      GTY817892Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Slide toward the front of the vehicle to insert the guide and attach the clip and claw.
      GTY799218Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Install in this Direction
    5. Fold the front seatback (RH side) forward and attach the clip and claw.
      GTY836667Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    6. Return the front seatback (RH side) to the original position and install the bolt.
      GTY817890Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    7. Install the upper console panel sub-assembly with the 2 bolts and 2 screws.
      GTY778124Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Bolt
      Screw
  7. INSTALL BOX PANEL SUB-ASSEMBLY 
    1. Slide toward the box panel sub-assembly front of the vehicle and attach the guide.
      GTY782933Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Install in this Direction
    2. Attach the clip.
      GTY817897Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Attach the clip.
      GTY836668Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Install the box panel sub-assembly with the 3 bolts and 2 screws.
      GTY787389Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Bolt
      Screw
  8. INSTALL NO. 1 GLOVE COMPARTMENT PANEL 

    Refer to PROCEDURE - Step 34

  9. INSTALL UPPER CONSOLE BOX 

    Refer to PROCEDURE - Step 6

  10. INSTALL SHIFTING HOLE COVER ASSEMBLY 

    Refer to PROCEDURE - Step 9

  11. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 1

  12. INSTALL NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY 

    Refer to INSTALLATION [05/2023 - ]

  13. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 35

  14. INSTALL FRONT DOOR NO. 2 OPENING TRIM COVER LH 

    Refer to PROCEDURE - Step 36

  15. INSTALL FRONT DOOR OPENING TRIM COVER LH 

    Refer to PROCEDURE - Step 38

  16. INSTALL FRONT DOOR SCUFF PLATE LH 

    Refer to PROCEDURE - Step 40

  17. INSTALL MULTI-DISPLAY WITH BRACKET 

    Refer to PROCEDURE - Step 3

  18. INSTALL NO. 2 INSTRUMENT PANEL SAFETY PAD COVER 

    Refer to PROCEDURE - Step 4

  19. INSTALL INSTRUMENT PANEL SAFETY PAD COVER 

    Refer to PROCEDURE - Step 5

  20. INSTALL COMBINATION METER ASSEMBLY 

    Refer to INSTALLATION [03/2017 - ]

  21. CUSTOMIZE POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM 
    1. Reset the auto tilt away function setting to the previous condition by changing the customize parameter.

      Refer to CUSTOMIZE PARAMETERS [03/2017 - ]

scientia non olet · About LEMON Manuals