LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2020 >> UX 200 Luxury >> Repair and Diagnosis >> Drivelines & Axles >> Wheel Hubs >> Axle And Differential (Service Information) >> REAR AXLE CARRIER (for AWD) >> Installation [10/2018 - 07/2022] >> Procedure

Installation [10/2018 - 07/2022]: Procedure

  1. TEMPORARILY INSTALL REAR AXLE CARRIER SUB-ASSEMBLY 
    1. Temporarily install the rear axle carrier sub-assembly to the rear upper control arm assembly with the bolt (B) and nut (C).
      GTY834134Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      NOTE:
      • Insert the bolt (B) with the threaded end facing the rear of the vehicle.
      • Because the nut (C) has its own stopper, do not turn the nut (C). Tighten the bolt (B) with the nut (C) secured.
    2. Temporarily install the rear shock absorber assembly to the rear axle carrier sub-assembly with the nut (D).
      NOTE:

      Hold the rear axle carrier pin while rotating the nut (D).

    3. Install the rear trailing arm assembly to the rear axle carrier sub-assembly with the 2 bolts (A).

      Torque: 135 N.m (1377 kgf/cm, 100 ft.lbf) 

      GTY826716Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  2. TEMPORARILY INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY 

    Refer to PROCEDURE - Step 1

  3. INSTALL REAR LOWER COIL SPRING INSULATOR 

    Refer to PROCEDURE - Step 2

  4. INSTALL REAR UPPER COIL SPRING INSULATOR 

    Refer to PROCEDURE - Step 1

  5. INSTALL REAR COIL SPRING 

    Refer to PROCEDURE - Step 3

  6. STABILIZE SUSPENSION 

    Refer to PROCEDURE - Step 4

  7. TIGHTEN REAR UPPER CONTROL ARM ASSEMBLY 

    Refer to PROCEDURE - Step 8

  8. FULLY TIGHTEN REAR NO. 1 SUSPENSION ARM ASSEMBLY 

    Refer to PROCEDURE - Step 10

  9. FULLY TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY 
    1. for Rear Axle Carrier Side:

      Refer to PROCEDURE - Step 12

  10. INSTALL REAR SHOCK ABSORBER ASSEMBLY 

    Refer to PROCEDURE - Step 7

  11. INSTALL REAR STABILIZER LINK ASSEMBLY 

    Refer to PROCEDURE - Step 5

  12. INSTALL REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH (w/ Height Control Sensor) 

    Refer to INSTALLATION [10/2018 - ]

  13. INSTALL FLEXIBLE HOSE BRACKET 
    1. Install the flexible hose bracket to the rear axle carrier sub-assembly with the bolt.

      Torque: 29 N.m (296 kgf/cm, 21 ft.lbf) 

  14. INSTALL REAR AXLE HUB AND BEARING ASSEMBLY 

    See step  1

  15. CONNECT REAR SPEED SENSOR 

    See step  12

  16. INSTALL REAR DISC 

    Refer to PROCEDURE - Step 1

  17. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY 

    See step  9

  18. INSTALL REAR AXLE SHAFT NUT 

    Refer to PROCEDURE - Step 2

  19. INSTALL REAR WHEEL 

    Refer to INSTALLATION [10/2018 - ]

  20. FULLY TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY 
    1. for Rear Suspension Member Side:

      Refer to PROCEDURE - Step 16

  21. INSTALL REAR FLOOR SIDE MEMBER COVER LH (for LH Side) 
    1. Engage the clip to install the rear floor side member cover LH.
    2. Install the clip.
    3. Install the 3 bolts.

      Torque: 7.5 N.m (76 kgf/cm, 66 in.lbf) 

  22. INSTALL NO. 1 FLOOR UNDER COVER ASSEMBLY (for RH Side) 
    1. Engage the clip to install the No. 1 floor under cover assembly.
    2. Install the 3 bolts.

      Torque: 7.5 N.m (76 kgf/cm, 66 in.lbf) 

  23. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL 

    Refer to PROCEDURE - Step 10

  24. INSPECT AND ADJUST REAR WHEEL ALIGNMENT 

    Refer to ADJUSTMENT [10/2018 - 07/2022]

  25. CHECK FOR SPEED SENSOR SIGNAL 

    Refer to TEST MODE PROCEDURE [10/2018 - ]

  26. PERFORM INITIALIZATION 
    Parking Support Brake System Refer to CALIBRATION [10/2018 - ]
    Parking Assist Monitor System Refer to CALIBRATION [10/2018 - 07/2022]
    Lighting System (EXT) Refer to INITIALIZATION [10/2018 - 10/2020] , or refer to INITIALIZATION [10/2020 - ]
scientia non olet · About LEMON Manuals