DTC Chart: IPC
Diagnostics in this article assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods .
DTC Chart - IPC
| DTC | Description | Action |
|---|---|---|
| P0381:01 | Glow Plug/Heater Indicator Control Circuit/Open: General Electrical Failure | GO to Pinpoint Test BV |
| P0460:11 | Fuel Level Sensor "A" Circuit: Circuit Short To Ground | GO to Pinpoint Test B |
| P0460:13 | Fuel Level Sensor "A" Circuit: Circuit Open | GO to Pinpoint Test B |
| P1534:01 | Restraint Deployment Indicator Circuit: General Electrical Failure | INSTALL a new IPC. Refer to Instrument Panel Cluster (IPC)
. DIAGNOSE RCM Diagnostic Trouble Codes (DTCs). REFER to: Airbag Supplemental Restraint System (SRS) . |
| P1706:00 | High Vehicle Speed Observed in Park: No Sub Type Information | GO to Pinpoint Test AL |
| U0100:00 | Lost Communication With ECM/PCM "A": No Sub Type Information | GO to Pinpoint Test BA |
| U0101:00 | Lost Communication With TCM: No Sub Type Information | GO to Pinpoint Test BB |
| U0104:00 | Lost Communication With Cruise Control Module: No Sub Type Information | GO to Pinpoint Test BC |
| U0121:00 | Lost Communication With Anti-Lock Brake System (ABS) Control Module: No Sub Type Information | GO to Pinpoint Test BD |
| U0131:00 | Lost Communication With Power Steering Control Module "A": No Sub Type Information | GO to Pinpoint Test BE |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to Pinpoint Test BF |
| U0146:00 | Lost Communication With Gateway "A": No Sub Type Information | GO to Pinpoint Test BG |
| U0151:00 | Lost Communication With Restraints Control Module: No Sub Type Information | GO to Pinpoint Test BH |
| U0151:87 | Lost Communication With Restraints Control Module: Missing Message | GO to Pinpoint Test BH |
| U0159:00 | Lost Communication With Parking Assist Control Module "A": No Sub Type Information | GO to Pinpoint Test BI |
| U0184:00 | Lost Communication With Radio: No Sub Type Information | GO to Pinpoint Test BJ |
| U0198:00 | Lost Communication With Telematic Control Module: No Sub Type Information | GO to Pinpoint Test BK |
| U0199:00 | Lost Communication With Door Control Module A: No Sub Type Information | GO to Pinpoint Test BL |
| U0212:00 | Lost Communication With Steering Column Control Module: No Sub Type Information | GO to Pinpoint Test BM |
| U0232:00 | Lost Communication With Side Obstacle Detection Control Module-Left: No Sub Type Information | GO to Pinpoint Test BN |
| U0233:00 | Lost Communication With Side Obstacle Detection Control Module-Right: No Sub Type Information | GO to Pinpoint Test BO |
| U023A:00 | Lost Communication With Image Processing Module "A": No Sub Type Information | GO to Pinpoint Test BP |
| U0401:00 | Invalid Data Received From ECM/PCM A: No Sub Type Information | GO to Pinpoint Test BA |
| U0401:81 | Invalid Data Received From ECM/PCM A: Invalid Serial Data Received | GO to Pinpoint Test BA |
| U0401:82 | Invalid Data Received From ECM/PCM A: Alive/Sequence Counter Incorrect/Not Updated | GO to Pinpoint Test BA |
| U0401:86 | Invalid Data Received From ECM/PCM A: Signal Invalid | GO to Pinpoint Test BA |
| U0415:00 | Invalid Data Received From Anti-Lock Brake System (ABS) Control Module: No Sub Type Information | GO to Pinpoint Test BD |
| U0415:82 | Invalid Data Received From Anti-Lock Brake System (ABS) Control Module: Alive/Sequence Counter Incorrect/Not Updated | GO to Pinpoint Test BD |
| U0422:00 | Invalid Data Received From Body Control Module: No Sub Type Information | GO to Pinpoint Test BF |
| U0422:82 | Invalid Data Received From Body Control Module: Alive/Sequence Counter Incorrect/Not Updated | GO to Pinpoint Test BF |
| U0424:00 | Invalid Data Received from HVAC Control Module: No Sub Type Information | GO to Pinpoint Test BQ |
| U0424:81 | Invalid Data Received from HVAC Control Module: Invalid Serial Data Received | GO to Pinpoint Test BQ |
| U0424:82 | Invalid Data Received from HVAC Control Module: Alive/Sequence Counter Incorrect/Not Updated | GO to Pinpoint Test BQ |
| U0431:82 | Invalid Data Received from Body Control Module "A": Alive/Sequence Counter Incorrect/Not Updated | GO to Pinpoint Test BF |
| U0452:81 | Invalid Data Received From Restraints Control Module: Invalid Serial Data Received | GO to Pinpoint Test BH |
| U0533:00 | Invalid Data Received from Side Obstacle Detection Control Module - Left: No Sub Type Information | GO to Pinpoint Test BN |
| U0533:56 | Invalid Data Received from Side Obstacle Detection Control Module - Left: Invalid/Incompatible Configuration | GO to Pinpoint Test BR |
| U0534:00 | Invalid Data Received from Side Obstacle Detection Control Module - Right: No Sub Type Information | GO to Pinpoint Test BO |
| U0534:56 | Invalid Data Received from Side Obstacle Detection Control Module - Right: Invalid/Incompatible Configuration | GO to Pinpoint Test BR |
| U053B:56 | Invalid Data Received From Image Processing Module A: Invalid/Incompatable Configuration | GO to Pinpoint Test BS |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | GO to Pinpoint Test BT |
| U2200:00 | Control Module Configuration Memory Corrupt: No Sub Type Information | GO to Pinpoint Test BU |
| U3000:44 | Control Module: Data Memory Failure | GO to Pinpoint Test BU |
| U3006:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test BW |
| U3006:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test BX |
| U300A:64 | Ignition Switch: Signal Plausibility Failure | DTC U300A:64 sets in continuous memory when the IPC detects a messaged START input for 15 seconds or longer. Once the fault condition is detected, the IPC operates with limited functionality for 15 seconds then returns to full functionality. DIAGNOSE any ignition or starting system concerns. REFER to: Steering Wheel and Column Electrical Components . |