Diagnostic Trouble Code (DTC) Chart
Diagnostics in this article assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods .
| Module | DTC | Description | Action |
|---|---|---|---|
| BCM | B1048:01 | Brake Fluid Level Switch: General Electrical Failure | GO to Pinpoint Test N |
| BCM | B1048:7B | Brake Fluid Level Switch: Low Fluid Level | GO to Pinpoint Test N |
| BCM | B10F1:14 | Key In Switch: Circuit Short To Ground Or Open | GO to Pinpoint Test AU |
| BCM | C1D00:11 | Park Brake Apply Switch: Circuit Short To Ground | GO to Pinpoint Test N |
| IPC | P0460:11 | Fuel Level Sensor "A" Circuit: Circuit Short To Ground | GO to Pinpoint Test B |
| IPC | P0460:13 | Fuel Level Sensor "A" Circuit: Circuit Open | GO to Pinpoint Test B |
| IPC | P1534:01 | Restraint Deployment Indicator Circuit: General Electrical Failure | GO to Pinpoint Test BX |
| IPC | P1706:00 | High Vehicle Speed Observed in Park: No Sub Type Information | GO to Pinpoint Test AJ |
| IPC | U0100:00 | Lost Communication With ECM/PCM "A": No Sub Type Information | GO to Pinpoint Test BF |
| IPC | U0104:00 | Lost Communication With Cruise Control Module: No Sub Type Information | GO to Pinpoint Test BG |
| IPC | U0121:00 | Lost Communication With Anti-Lock Brake System (ABS) Control Module "A": No Sub Type Information | GO to Pinpoint Test BH |
| IPC | U0131:00 | Lost Communication With Power Steering Control Module: No Sub Type Information | GO to Pinpoint Test BI |
| IPC | U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to Pinpoint Test BJ |
| IPC | U0146:00 | Lost Communication With Serial Data Gateway "A": No Sub Type Information | GO to Pinpoint Test BL |
| IPC | U0151:00 | Lost Communication With Restraints Control Module: No Sub Type Information | GO to Pinpoint Test BM |
| IPC | U0159:00 | Lost Communication With Parking Assist Control Module "A": No Sub Type Information | GO to Pinpoint Test BN |
| IPC | U0184:00 | Lost Communication With Radio: No Sub Type Information | GO to Pinpoint Test BO |
| IPC | U0212:00 | Lost Communication With Steering Column Control Module: No Sub Type Information | GO to Pinpoint Test BP |
| IPC | U0232:00 | Lost Communication With Side Obstacle Detection Control Module "A": No Sub Type Information | GO to Pinpoint Test BQ |
| IPC | U0233:00 | Lost Communication With Side Obstacle Detection Control Module "B": No Sub Type Information | GO to Pinpoint Test BR |
| IPC | U023A:00 | Lost Communication With Image Processing Module A: No Sub Type Information | GO to Pinpoint Test BS |
| IPC | U0244:00 | Lost Communication With Running Board Control Module A: No Sub Type Information | GO to Pinpoint Test BT |
| IPC | U0401:00 | Invalid Data Received from ECM/PCM A: No Sub Type Information | GO to Pinpoint Test BF |
| IPC | U0401:81 | Invalid Data Received from ECM/PCM A: Invalid Serial Data Received | GO to Pinpoint Test BF |
| IPC | U0401:82 | Invalid Data Received from ECM/PCM A: Alive/Sequence Counter Incorrect/Not Updated | GO to Pinpoint Test BF |
| IPC | U0401:86 | Invalid Data Received from ECM/PCM A: Signal Invalid | GO to Pinpoint Test BF |
| IPC | U0415:00 | Invalid Data Received from Anti-Lock Brake System (ABS) Control Module "A": No Sub Type Information | GO to Pinpoint Test BH |
| IPC | U0415:82 | Invalid Data Received from Anti-Lock Brake System (ABS) Control Module "A": Alive/Sequence Counter Incorrect/Not Updated | GO to Pinpoint Test BH |
| IPC | U0422:00 | Invalid Data Received From Body Control Module: No Sub Type Information | GO to Pinpoint Test BJ |
| IPC | U0422:82 | Invalid Data Received From Body Control Module: Alive/Sequence Counter Incorrect/Not Updated | GO to Pinpoint Test BJ |
| IPC | U0424:00 | Invalid Data Received From HVAC Control Module: No Sub Type Information | GO to Pinpoint Test BK |
| IPC | U0424:81 | Invalid Data Received From HVAC Control Module: Invalid Serial Data Received | GO to Pinpoint Test BK |
| IPC | U0424:82 | Invalid Data Received From HVAC Control Module: Alive/Sequence Counter Incorrect/Not Updated | GO to Pinpoint Test BK |
| IPC | U0431:82 | Invalid Data Received From Body Control Module "A": Alive/Sequence Counter Incorrect/Not Updated | GO to Pinpoint Test BJ |
| IPC | U0452:81 | Invalid Data Received From Restraints Control Module: Invalid Serial Data Received | GO to Pinpoint Test BM |
| IPC | U0533:00 | Invalid Data Received From Side Obstacle Detection Control Module "A": No Sub Type Information | GO to Pinpoint Test BQ |
| IPC | U0533:56 | Invalid Data Received From Side Obstacle Detection Control Module "A": Invalid/Incompatible Configuration | GO to Pinpoint Test BW |
| IPC | U0533:82 | Invalid Data Received From Side Obstacle Detection Control Module "A": Alive/Sequence Counter Incorrect/Not Updated | GO to Pinpoint Test BQ |
| IPC | U0534:00 | Invalid Data Received From Side Obstacle Detection Control Module "B": No Sub Type Information | GO to Pinpoint Test BR |
| IPC | U0534:56 | Invalid Data Received From Side Obstacle Detection Control Module "B": Invalid/Incompatible Configuration | GO to Pinpoint Test BW |
| IPC | U0534:82 | Invalid Data Received From Side Obstacle Detection Control Module "B": Alive/Sequence Counter Incorrect/Not Updated | GO to Pinpoint Test BR |
| IPC | U053B:56 | Invalid Data Received From Image Processing Module A: Invalid/Incompatible Configuration | GO to Pinpoint Test BU |
| IPC | U0545:56 | Invalid Data Received From Running Board Control Module "A": Invalid/Incompatible Configuration | GO to Pinpoint Test BV |
| IPC | U2100:00 | Initial Configuration Not Complete: No Sub Type Information | GO to Pinpoint Test BY |
| IPC | U2200:00 | Control Module Configuration Memory Corrupt: No Sub Type Information | GO to Pinpoint Test BZ |
| IPC | U3000:44 | Control Module: Data Memory Failure | GO to Pinpoint Test BZ |
| IPC | U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test CA |
| IPC | U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test CB |
| IPC | U300A:64 | Ignition Switch: Signal Plausibility Failure | GO to Pinpoint Test CC |
| PCM | P0461:00 | Fuel Level Sensor "A" Circuit Range/Performance: No Sub Type Information | GO to Pinpoint Test B |
| PCM | P0462:00 | Fuel Level Sensor "A" Circuit Low: No Sub Type Information | GO to Pinpoint Test B |
| PCM | P0463:00 | Fuel Level Sensor "A" Circuit High: No Sub Type Information | GO to Pinpoint Test B |
| PCM | P0521:00 | Engine Oil Pressure Sensor/Switch "A" Circuit Range/Performance: No Sub Type Information | GO to Pinpoint Test Y |
| PCM | P0521:00 | Engine Oil Pressure Sensor/Switch "A" Circuit Range/Performance: No Sub Type Information | GO to Pinpoint Test Z |
| PCM | P0522:00 | Engine Oil Pressure Sensor/Switch "A" Circuit Low: No Sub Type Information | GO to Pinpoint Test Y |
| PCM | P0522:00 | Engine Oil Pressure Sensor/Switch "A" Circuit Low: No Sub Type Information | GO to Pinpoint Test Z |
| PCM | P0523:00 | Engine Oil Pressure Sensor/Switch "A" Circuit High: No Sub Type Information | GO to Pinpoint Test Y |
| PCM | P0523:00 | Engine Oil Pressure Sensor/Switch "A" Circuit High: No Sub Type Information | GO to Pinpoint Test Z |
| PCM | P0524:00 | Engine Oil Pressure Too Low: No Sub Type Information | GO to Pinpoint Test Y |
| PCM | P0524:00 | Engine Oil Pressure Too Low: No Sub Type Information | GO to Pinpoint Test Z |
| PCM | P25B0:00 | Fuel Level Sensor "A" Stuck: No Sub Type Information | GO to Pinpoint Test B |
| SCCM | B1380:11 | Steering Wheel Right Switch Pack: Circuit Short To Ground | GO to Pinpoint Test AF |
| SCCM | B1380:12 | Steering Wheel Right Switch Pack: Circuit Short To Battery | GO to Pinpoint Test AF |
| SCCM | B1380:1C | Steering Wheel Right Switch Pack: Circuit Voltage Out Of Range | GO to Pinpoint Test AF |
| SCCM | B1380:95 | Steering Wheel Right Switch Pack: Incorrect Assembly | GO to Pinpoint Test AF |
| SCCM | B1380:9E | Steering Wheel Right Switch Pack: Stuck On | GO to Pinpoint Test AF |