Installing the engine wiring harness for the sensor system 1
Engine wiring harness for sensor system 1
NOTE:
RISK OF DAMAGE
Improper routing of cables and wiring harnesses .
Trapped, crushed or damaged cables may cause short circuits and malfunctions .
Improper routing of cables and wiring harnesses .
Trapped, crushed or damaged cables may cause short circuits and malfunctions .
- Route all cables without abrasions, do not trap and crush.
- Guide in and install the wiring harness section (1)
for sensor system 1.
- Connect connectors (3)
and lock.
The connector (3) must engage audibly.
- Tighten down screw (2)
.TIGHTENING TORQUES SPECIFICATION
Wiring harness section for engine to cylinder head cover M6 Tightening torque 8 Nm - Guide in the wiring harness section (1) and install.
- Guide in and install the wiring harness section (3) for sensor system 1.
- Connect connectors (2)
and lock.
The connectors (2) must engage audibly.
- Secure clamps (arrow).
- Connect connectors (1)
and lock.
The connector (1) must engage audibly.
- Position the acoustic cover (2) .
- Fasten expanding rivet (1) .
- Secure clamps (arrow).
- Fasten expanding rivet (1)
.
- Fasten the Christmas tree clip (2) .
- Secure expanding rivet (1) .
- Secure the clamps (arrows).
- Connect connectors (1) and lock.
- Make sure the connector (1) engages audibly.
- Insert and install the positive battery cable (3) .
- Secure positive battery cable (3) at the clamp (4) .
- Tighten the nut (2)
hand-tight.CAUTION: Improper routing of the positive battery cable .
Risk of short circuits!- Route the positive battery cable without abrasions and do not trap.
- Correctly attach the positive battery cable (1) to the anti-twist lock (2) .
- Tighten nut (3)
.TIGHTENING TORQUES SPECIFICATION
Battery positive lead to starter M8 Tightening torque 13.5 Nm - Tighten down screws (1)
.TIGHTENING TORQUES SPECIFICATION
Cable bracket on rear cylinder head/transmission M6x20 Tightening torque 10 Nm - Guide in the wiring harness section (2) and install.
- Make sure the locking mechanism (arrow) engages audibly.
- Tighten down screws (1)
.TIGHTENING TORQUES SPECIFICATION
Cable bracket on rear cylinder head/transmission M6x20 Tightening torque 10 Nm - Guide in and install the wiring harness section (5) for sensor system 1.
- Secure clamps (arrow).
- Connect connectors (4)
and lock.
The connector (4) must engage audibly.
- Connect connectors (3)
and lock.
The connector (3) must engage audibly.
- Connect connectors (2)
and lock.
The connectors (2) must engage audibly.
- Connect connectors (1)
and lock.
The connectors (1) must engage audibly.
- Guide in and install the wiring harness section (1)
for sensor system 1 on the bracket (2)
.
Follow-up work
- Refer to INSTALLING THE INTAKE PLENUM .
- Refer to INSTALLING THE TANK VENT VALVE .
- Refer to INSTALLING CONTROL UNIT BRACKET .
- Refer to INSTALLING THE INTEGRATED POWER SUPPLY MODULE (PDM) .
- Refer to INSTALLING THE DME CONTROL UNIT .
- Refer to INSTALLING ACOUSTIC COVER AT REAR .
- Refer to INSTALLING THE CENTER COWL UPPER PART .
- Refer to INSTALLING ACOUSTIC COVER .
- Refer to INSTALLING WINDSHIELD PANEL COVER .
- Refer to INSTALLING LEFT AND RIGHT WIPER ARM .
- Refer to INSTALLING THE REAR RIGHT ENGINE COMPARTMENT COVER .
- Refer to INSTALLING THE COVER OF THE ENGINE COMPARTMENT ON THE REAR LEFT .
- Refer to INSTALLING THE REAR HOOD SEAL .
- Refer to FILLING AND VENTING THE LOW-TEMPERATURE COOLANT CIRCUIT .
- Refer to ACTIVATING ELECTRICAL SYSTEM .
- Refer to INSTALLING UNDERBODY PROTECTION AT REAR .
- Refer to INSTALLING THE CENTER UNDERBODY PROTECTION .
- Refer to IF INSTALLED: INSTALLING UNDERBODY PROTECTION FOR THE STEERING .
- Refer to INSTALLING THE UNDERBODY PROTECTION OF THE STEERING GEAR .
- Refer to INSTALLING FRONT UNDERBODY PROTECTION .