Install timing case cover, bottom

Mounting the beaded metal gaskets 

• Clean sealing surfaces (2)  .
• Replace beaded metal gaskets (1)  .

  Parts:  Sheet metal beaded seals

• Securing the beaded metal gaskets (1)  with the timing case cover screws.
• For timing case cover or timing chain replacement: 

  Loosen screw (3)  .

  Remove jump guard (4)  .

  Position jump guard (4)  .

  Tighten down screw (3)  .

  Courtesy of BMW OF NORTH AMERICA, INC.

  TIGHTENING TORQUE SPECIFICATIONS
  
  

  Jump guard
  M6x25	Tightening torque	10 Nm

• For timing case cover or timing chain replacement: 

  Release and remount coolant temperature sensor (1)  .

  Tighten the coolant temperature sensor (1)  .

  TIGHTENING TORQUE SPECIFICATIONS
  
  

  Water/oil temperature sensor
  Sensor M12x1.5	Tightening torque	18 Nm

  Courtesy of BMW OF NORTH AMERICA, INC.

• The centering pins (1)  must not be damaged, replace if necessary.

  Courtesy of BMW OF NORTH AMERICA, INC.

• (1)  Clean sealing surfaces.

  Courtesy of BMW OF NORTH AMERICA, INC.

  Tightening the screw connection 1 on the front timing case cover 

• Position the timing case cover.
• Tighten screws in the order (1)  to (2)  .
  TIGHTENING TORQUE SPECIFICATIONS
  
  

  Timing case cover on bottom crankcase
  M8x45, M8x55, M8x65, M8x85	tightening torque	25 Nm

  Fig 1: Timing Case Cover Screws Tightening Sequence

  Courtesy of BMW OF NORTH AMERICA, INC.

  Securing the screw connection 2 on the front timing case cover 

• Tighten screws in the order (3)  to (9)  .
  TIGHTENING TORQUE SPECIFICATIONS
  
  

  Timing case cover on bottom crankcase
  M8x45, M8x55, M8x65, M8x85	tightening torque	25 Nm

  Fig 2: Timing Case Cover Screws Tightening Sequence

  Courtesy of BMW OF NORTH AMERICA, INC.

  Mounting the screw connection 3 on the front timing case cover 

• Position the carrier plate (1)  .
• Tighten screws in the order (10)  to (12)  .
  TIGHTENING TORQUE SPECIFICATIONS
  
  

  Timing case cover on bottom crankcase
  M8x45, M8x55, M8x65, M8x85	tightening torque	25 Nm

  Fig 3: Timing Case Cover Screws Tightening Sequence

  Courtesy of BMW OF NORTH AMERICA, INC.
• Connect and lock the plug connection (1)  to the coolant temperature sensor (2)  .

Courtesy of BMW OF NORTH AMERICA, INC.

Follow-up work 

• Refer to INSTALLING THE UPPER OIL SUMP SECTION .
• Refer to INSTALLING THE VIBRATION DAMPER .
• Refer to INSTALLING FRONT AXLE DIFFERENTIAL .
• Refer to INSTALLING OIL PUMP .
• Refer to INSTALLING THE LOWER OIL PAN SECTION .
• Refer to INSTALLING THE RIGHT CYLINDER HEAD .
• Refer to INSTALLING BOTH RIGHT VANOS ADJUSTERS .
• Refer to REMOVING THE SPECIAL TOOL TO PRETENSION THE TIMING CHAIN AT CYLINDER BANK 1 .
• Refer to INSTALLING THE HYDRAULIC CHAIN TENSIONER OF CYLINDER BANK 1 .
• Refer to INSTALLING THE SEALING CAP ON THE CYLINDER HEAD OF CYLINDER BANK 1 .
• Refer to INSTALLING THE CYLINDER HEAD COVER ON THE RIGHT .
• Refer to INSTALLING VANOS SOLENOID ACTUATOR, EXHAUST OF CYLINDER BANK 1 .
• Refer to INSTALLING THE VANOS SOLENOID ACTUATOR INTAKE OF CYLINDER BANK 1 .
• Refer to INSTALLING THE INJECTORS FOR THE CYLINDERS 1 TO 4 .
• Refer to SECURING THE WIRING HARNESS SECTION OF THE CYLINDER HEAD COVER ON THE RIGHT .
• Refer to INSTALLING RIGHT HIGH PRESSURE PUMP .
• Refer to INSTALLING FUEL DELIVERY LINE .
• Refer to INSTALLING THE RIGHT HIGH-PRESSURE RAIL .
• Refer to INSTALLING THE GUIDE TUBE FOR THE OIL DIPSTICK .
• Refer to INSTALLING THE OIL FILLER CAP .
• Refer to INSTALLING IGNITION COILS OF CYLINDER BANK 1 .
• Refer to INSTALLING THE ENGINE VENTILATION LINE OF CYLINDERS 1 TO 4 .
• Refer to INSTALLING THE LEFT CYLINDER HEAD .
• Refer to INSTALLING BOTH LEFT VANOS ADJUSTERS .
• Refer to REMOVING SPECIAL TOOL TO PRETENSION TIMING CHAIN ON CYLINDER BANK 2 .
• Refer to INSTALLING THE HYDRAULIC CHAIN TENSIONER OF CYLINDER BANK 2 .
• Refer to INSTALLING THE TIMING CASE COVER ON THE CYLINDER HEAD OF CYLINDER BANK 2 .
• Refer to INSTALLING THE LEFT CYLINDER HEAD COVER .
• Refer to INSTALLING THE VANOS SOLENOID ACTUATOR EXHAUST OF CYLINDER BANK 2 .
• Refer to INSTALLING VANOS SOLENOID ACTUATOR, INTAKE OF CYLINDER BANK 2 .
• Refer to INSTALLING FUEL DELIVERY LINE .
• Refer to SECURING THE WIRING HARNESS SECTION FROM THE CYLINDER HEAD COVER ON THE LEFT .
• Refer to INSERTING THE EXHAUST TURBOCHARGER FOR THE CYLINDERS 5 TO 8 .
• Refer to INSTALLING THE ENGINE VENTILATION LINE OF CYLINDERS 5 TO 8 .
• Refer to INSTALLING THE INTAKE PIPE OF THE ENGINE VENTILATION LINE .
• Refer to INSTALLING THE BELT PULLEY ON THE TORSIONAL VIBRATION DAMPER .
• Refer to INSTALLING THE BELT TENSIONER .
• Refer to INSTALLING COOLANT PUMPS .
• Refer to INSTALLING RIGHT CLEAN AIR PIPE .
• Refer to INSTALLING LEFT CLEAN AIR PIPE .
• Refer to INSTALLING THE LEFT ENGINE VENTILATION LINE (PARTIALLY REMOVED) .
• Refer to INSTALLING THE RIGHT-HAND CHARGE AIR COOLER .
• Refer to INSTALLING THE LEFT-HAND CHARGE AIR COOLER .
• Refer to CONNECTING THE LEFT CHARGE AIR LINE TO THE EXHAUST TURBOCHARGER .
• Refer to CONNECTING THE RIGHT CHARGE AIR LINE TO THE EXHAUST TURBOCHARGER .
• Refer to INSTALLING THE CARRIER PLATE .
• Refer to PREPARING THE INJECTORS FOR INSTALLATION .
• Refer to INSTALLING THE INJECTORS FOR THE CYLINDERS 5 TO 8 .
• Refer to CONNECTING THE CONNECTOR OF THE INJECTORS OF CYLINDER BANK 2 .
• Refer to INSTALLING THE LEFT HIGH PRESSURE PUMP .
• Refer to INSTALLING THE HIGH-PRESSURE RAIL ON THE LEFT .
• Refer to INSTALLING THE SOUND INSULATION OF THE INJECTORS, LEFT .
• Refer to INSTALLING THE IGNITION COILS OF CYLINDER BANK 2 .
• Refer to INSTALLING IGNITION COIL ON CYLINDER 1 .
• Refer to INSTALLING THE BELT PULLEY ON THE TORSIONAL VIBRATION DAMPER .
• Refer to INSTALLING THE BELT TENSIONER .
• Refer to INSTALLING DRIVE BELT .
• Refer to REMOVING THE ENGINE FROM THE ENGINE SUPPORT BRACKET .
• Refer to INSTALLING THE COMPLETE FRONT AXLE WITH THE ENGINE AND TRANSMISSION .
• Refer to INSTALLING THE OIL FILTER ELEMENT .
• Refer to TIGHTENING THE OIL DRAIN PLUG .
• Refer to FILLING ENGINE OIL .