Installing fuel delivery line

• Tighten the nut (1) at the left high pressure pump.
  TIGHTENING TORQUE SPECIFICATIONS
  
  

  Fuel delivery line to high pressure pump
  M14	Joining torque	10 Nm
  	Tightening torque	30 Nm

  Courtesy of BMW OF NORTH AMERICA, INC.

• Tighten down screw (2).
  TIGHTENING TORQUE SPECIFICATIONS
  
  

  Fuel supply line to cylinder head cover/cylinder head
  M6xl6	tightening torque	10 Nm

• Feed the fuel supply line in and position it.
• Hand-tighten  all screw connections.
• Tighten the nuts (1) of the fuel supply line on the high pressure pumps.
  TIGHTENING TORQUE SPECIFICATIONS
  
  

  Fuel delivery line to high pressure pump
  M14	Joining torque	10 Nm
  	Tightening torque	30 Nm

  Courtesy of BMW OF NORTH AMERICA, INC.

• Tighten the screw (2) on the right cylinder head cover.
  TIGHTENING TORQUE SPECIFICATIONS
  
  

  Fuel supply line to cylinder head cover/cylinder head
  M6xl6	tightening torque	10 Nm

• Tighten the screws (3).
  TIGHTENING TORQUE SPECIFICATIONS
  
  

  Fuel supply line to cylinder head cover/cylinder head
  M6xl6	tightening torque	10 Nm

• Insert and install the alternator (1).

  Courtesy of BMW OF NORTH AMERICA, INC.

• Route the positive battery cable (4) and connect it to the alternator.
• Tighten nut and mount cover (1).
  TIGHTENING TORQUE SPECIFICATIONS
  
  

  Positive battery cable to alternator
  M8	tightening torque	19 Nm

  Courtesy of BMW OF NORTH AMERICA, INC.

• Secure the positive battery cable (3) with the clamp (4) (arrow).
• Connect the connector (2) to the alternator and lock audibly.
  NOTE: RISK OF DAMAGE 
  Ground points that have not been screwed on. 
  Malfunction or failure of the DME. 

  • Screw all screw points of the cable ducts on again. Some of the screw points are also grounding points.
• Mount the cable shaft and tighten the screws (2).
  TIGHTENING TORQUE SPECIFICATIONS
  
  

  Cable duct to cylinder head cover/cylinder head
  M6 screw	tightening torque	10 Nm

  Courtesy of BMW OF NORTH AMERICA, INC.

• Lay the cable and connect the connector (1) with the exhaust turbochargers and lock it.
• Connect the connector (3) of the exhaust camshaft sensor and lock it.
• Remove the special tool 0 496 565 (13 5 160)(2) from the fuel line (1). 
• Remove the special tool 0 496 565 (13 5 160)(3) from the fuel supply line (4). 

  Courtesy of BMW OF NORTH AMERICA, INC.

• Connect the fuel line to the fuel line (2) to the fuel feed line (1) and lock it audibly.
• Install the safety ring.

  Courtesy of BMW OF NORTH AMERICA, INC.

Follow-up work 

• Refer to INSTALLING THE RIGHT-HAND CHARGE AIR COOLER .
• Refer to INSTALLING THE LEFT-HAND CHARGE AIR COOLER .
• Refer to INSTALLING DRIVE BELT .
• Refer to INSTALLING THE COOLANT EXPANSION TANK FOR THE LOW-TEMPERATURE COOLANT CIRCUIT .
• Refer to INSTALLING IGNITION COIL ON CYLINDER 1 .
• Refer to INSTALLING IGNITION COIL ON CYLINDER 5 .
• Refer to INSTALLING LEFT CLEAN AIR PIPE .
• Refer to INSTALLING RIGHT CLEAN AIR PIPE .
• Refer to CONNECTING THE RIGHT CHARGE AIR LINE TO THE EXHAUST TURBOCHARGER .
• Refer to CONNECTING THE LEFT CHARGE AIR LINE TO THE EXHAUST TURBOCHARGER .
• Refer to CONNECTING THE COOLANT HOSE TO THE AUXILIARY COOLANT PUMP .
• Refer to INSTALLING FRONT UNDERBODY PROTECTION .
• Refer to INSTALLING FAN COWL .
• Refer to INSTALLING THE REAR TOP CROSS CONNECTION .
• Refer to INSTALLING THE RIGHT AND LEFT UNFILTERED-AIR DUCT .
• Refer to INSTALLING THE LEFT INTAKE SILENCER BRACKET .
• Refer to INSTALLING BRACKET FOR RIGHT INTAKE SILENCER .
• Refer to INSTALLING BOTH INTAKE FILTER HOUSING .
• Refer to INSTALLING ACOUSTIC COVER .
• Refer to INSTALLING TENSION STRUT ON LEFT AND RIGHT SHOCK TOWER .
• Refer to INSTALLING UPPER CROSS CONNECTION .
• Refer to INSTALLING THE COVER IN THE ENGINE COMPARTMENT AT TOP LEFT AND RIGHT .