Install the acoustic cover for the oil sump

• Insert and position the acoustic cover (1) of the oil pan.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Secure expanding rivet (1).
• Replace the Christmas tree clip (2).

  Parts:  Christmas Tree clip

• Attach the Christmas tree clip (2).

  Courtesy of BMW OF NORTH AMERICA, INC.

• Secure expanding rivet (1).

  Courtesy of BMW OF NORTH AMERICA, INC.

• Secure expanding rivet (1).

  Courtesy of BMW OF NORTH AMERICA, INC.

  NOTE: The following step(s) must be performed if the listed component(s) is/are installed.
• Position the transmission oil lines (1) on the bracket (2).

  Make sure the marks (3) are positioned correctly on the holder (2).

  Courtesy of BMW OF NORTH AMERICA, INC.

  NOTE: The following step(s) must be performed if the listed component(s) is/are installed.
• Insert and install the holder (1).

  Courtesy of BMW OF NORTH AMERICA, INC.

  NOTE: The following step(s) must be performed if the listed component(s) is/are installed.
• Tighten down screw (1).
  TIGHTENING TORQUES SPECIFICATION
  
  

  Holder for transmission oil line
  Screw	Tightening torque	4 Nm

  Courtesy of BMW OF NORTH AMERICA, INC.

• Connect and lock the connector (1).
• Make sure the connector (1) engages audibly.
• Insert and install the positive battery cable (3).
• Secure positive battery cable (3) at the clamp (4).
• Tighten the nut (2) hand-tight.

  Courtesy of BMW OF NORTH AMERICA, INC.

  CAUTION: Improper routing of the positive battery cable. 
  Risk of short circuits! 

  • Route the positive battery cable without abrasions and do not trap.
• Correctly  attach the positive battery cable (1) to the anti-twist lock (2).
• Tighten the nut (3).
  TIGHTENING TORQUES SPECIFICATION
  
  

  Battery positive lead to starter
  M8	Tightening torque	13.5 Nm

  Courtesy of BMW OF NORTH AMERICA, INC.

Follow-up work 

• Refer to RAISING THE FRONT AXLE SUPPORT AND FASTEN IT .
• Refer to TAKING ENGINE OUT OF INSTALLATION ORIENTATION .
• Refer to SECURING THE ANTI-ROLL BAR LINK ON THE LEFT AND RIGHT ON THE ANTI-ROLL BAR .
• Refer to FASTENING ELECTRIC COOLANT PUMP AND COOLANT HOSES TO THE FRONT AXLE SUPPORT .
• Refer to IF INSTALLED: CONNECT THE VACUUM LINE OF THE ENGINE MOUNTS .
• Refer to ATTACHING THE LINE CONNECTION OF THE RIDE HEIGHT SENSOR
• Refer to SECURING THE EPS WIRING HARNESS TO THE ELECTROMECHANICAL STEERING GEAR .
• Refer to INSTALLING STEERING SHAFT AT BOTTOM ON STEERING GEAR
• Refer to INSTALLING THE COVER PANELS ON THE FRONT AXLE ON THE RIGHT AND LEFT .
• Refer to INSTALLING THE FRONT LEFT AND RIGHT WHEELS .
• Refer to INSTALLING THE SEAL FOR THE HOOD GASKET LEFT AND RIGHT .
• Refer to INSTALLING THE COVER IN THE ENGINE COMPARTMENT AT TOP LEFT AND RIGHT .
• Refer to INSTALLING THE FRONT HOOD SEAL AT THE REAR .
• Refer to INSTALLING THE COVER OF THE ENGINE COMPARTMENT ON THE REAR LEFT .
• Refer to INSTALLING THE REAR RIGHT ENGINE COMPARTMENT COVER .
• Refer to INSTALLING ACOUSTIC COVER .
• Refer to RECONNECTING ALL BATTERY GROUND LEADS
• Refer to INSTALLING THE FRONT UNDERBODY PROTECTION .
• Refer to INSTALLING THE CENTER UNDERBODY PROTECTION .
• Refer to INSTALLING UNDERBODY PROTECTION AT REAR .
• Refer to INSTALLING COVER ON EXHAUST SYSTEM .
• Refer to TAKING HOOD OUT OF THE SERVICE POSITION .