Install intake plenum
NOTE:
RISK OF DAMAGE
Improper routing of cables and wiring harnesses.
Trapped, crushed or damaged cables may cause short circuits and malfunctions.
Improper routing of cables and wiring harnesses.
Trapped, crushed or damaged cables may cause short circuits and malfunctions.
- Route all cables without abrasions, do not trap and crush.
NOTE:
TECHNICAL INFORMATION
Make sure that the connections are locked correctly. The locks must engage audibly.
Make sure that the connections are locked correctly. The locks must engage audibly.
- Replace seals (1).
Parts: Seals
- Clean the contact surface (1).NOTE: TECHNICAL INFORMATION Additional coolant can leakage. Make sure that no coolant enters the intake port of the cylinder head.
- Feed in and position the intake plenum (A) at the cylinder head.
- Tighten screws in the order (1) to (5).NOTE: Tighten the bolts in 360 degree steps.TIGHTENING TORQUES SPECIFICATION
Intake plenum to cylinder head M6 Tightening torque 10 Nm - Connect and lock the coolant feed line (1).
- Make sure that the coolant feed line (1) engages audibly.
- Tighten down screw (1).TIGHTENING TORQUES SPECIFICATION
Intake plenum to support M6X25 Tightening torque 8 Nm - Guide in and Install the wiring harness section (1) for the injectors and ignition coils.
The locks (arrows) must engage audibly.
- Guide in and Install the wiring harness section (2) for the injectors and ignition coils.
- Secure clamps (1).
- Guide in and install the wiring harness section (2) for sensor system 1.
- Secure clamps (1).
- Insert and install the tank vent line (1).
- Secure the tank vent line (1) to the clamp (2).
- Connect connectors (1) and lock.
- Make sure the connector (1) engages audibly.
- Tighten down screw (2).TIGHTENING TORQUES SPECIFICATION
Throttle body to holder M6X25 Tightening torque 8 Nm - Insert and install the coolant hose (2).
- Fasten the clamping collar (1) with the special tool 0 495 794 (17 2 050).
- Feed in and install the wiring harness section (3) for sensor system 2.
- Make sure that you can hear the locks (arrows) engage.
- Insert and install the tank vent line (2).
- Secure the tank vent line (2) to the clamp (3).
- Tighten down screw (1).TIGHTENING TORQUES SPECIFICATION
Tank vent line to intake plenum Oval-head screw Tightening torque 3 Nm - Connect connectors (1) and lock.
The connector (1) must engage audibly.
- Insert and install the tank vent line (1).
The locks (arrows) must engage audibly.
- Insert and install the holder (2).
- Ensure that the locking mechanism (1) engages audibly.
- Replace gasket (1).
Parts: Gasket
- Insert and install charge air line (1).
- Tighten screws (arrows).TIGHTENING TORQUES SPECIFICATION
Charge air line to throttle body M6 Tightening torque 8 Nm - Connect connectors (1) and lock.
- Connect connectors (2) and lock.
- Make sure you can hear the connectors (1) and (2) engage.
- Secure clamps (3).
Follow-up work
- Refer to INSTALLING THE TANK VENT VALVE .
- Refer to INSTALLING CONTROL UNIT BRACKET .
- Refer to INSTALLING THE INTEGRATED POWER SUPPLY MODULE (PDM) .
- Refer to INSTALLING THE DME CONTROL UNIT .
- Refer to INSTALLING ACOUSTIC COVER AT REAR .
- Refer to INSTALLING THE COWL UPPER PART .
- Refer to INSTALLING TENSION STRUT ON LEFT AND RIGHT SHOCK TOWER .
- Refer to INSTALLING WINDSHIELD PANEL COVER .
- Refer to INSTALLING LEFT AND RIGHT WIPER ARM .
- Refer to INSTALLING THE REAR RIGHT ENGINE COMPARTMENT COVER .
- Refer to INSTALLING THE COVER OF THE ENGINE COMPARTMENT ON THE REAR LEFT .
- Refer to INSTALLING THE FRONT HOOD SEAL AT THE REAR .
- Refer to FILLING THE LOW-TEMPERATURE COOLING SYSTEM WITH THE VACUUM FILLING EQUIPMENT .
- Refer to RECONNECTING ALL BATTERY GROUND LEADS
- Refer to VENTING THE LOW-TEMPERATURE COOLING SYSTEM .
- Refer to INSTALLING ACOUSTIC COVER .
- Refer to INSTALLING THE FRONT LEFT BOTTOM WHEEL ARCH COVER .
- Refer to INSTALLING THE CENTER UNDERBODY PROTECTION .
- Refer to INSTALLING THE FRONT UNDERBODY PROTECTION .