Installing the component carrier

NOTE: RISK OF DAMAGE
Damage to the surface.
The use of metal-cutting tools (e.g., emery cloths) for cleaning surfaces can damage them and lead to leaks and/or engine damage.

Do not use any metal-cutting tools.

NOTE: TECHNICAL INFORMATION
The sealing surfaces must be free of oil, grease and cleaning agents.

Check centering sleeves (1) in the marked area for damage and replace centering sleeves (1) if necessary.

Courtesy of BMW OF NORTH AMERICA, INC.
Clean sealing surfaces (1) with special tool 0 495 102 (11 4 470) .

Courtesy of BMW OF NORTH AMERICA, INC.
Guide the connecting pipe (1) out of the component carrier (2) in the arrow direction and remove it.

Courtesy of BMW OF NORTH AMERICA, INC.
Replace sealing rings (1) on thee connecting pipe (2).
Parts: Sealing ring
Coat sealing rings (1) with coolant before installing.

Courtesy of BMW OF NORTH AMERICA, INC.
Guide the connecting pipe (1) in the arrow direction and install it on the component carrier (2).

Courtesy of BMW OF NORTH AMERICA, INC.
Replace sealing ring (1).
Parts: Sealing ring

Courtesy of BMW OF NORTH AMERICA, INC.
CAUTION:
Heavy component.
Heavy components can lead to injury or damage.
- Remove and install heavy components with the aid of another person/other persons.
Courtesy of BMW OF NORTH AMERICA, INC.
Insert and install function carrier (1) using the connecting pipe (2).
NOTE: Lay the air conditioning compressor to one side with an assistant so that the screws on the component carrier can be tightened more easily.
Hand-tighten the bolts (1).

Courtesy of BMW OF NORTH AMERICA, INC.
Hand-tighten the bolts (1).

Courtesy of BMW OF NORTH AMERICA, INC.

Tighten down screws (1).

TIGHTENING TORQUE SPECIFICATIONS

Coolant pump with function carrier on crankcase
M8x35	tightening torque	19 Nm

Courtesy of BMW OF NORTH AMERICA, INC.

Tighten down screws (1).

TIGHTENING TORQUE SPECIFICATIONS

Coolant pump with function earner on crankcase
M8x35	tightening torque	19 Nm

Courtesy of BMW OF NORTH AMERICA, INC.

Secure clamps (1).

Courtesy of BMW OF NORTH AMERICA, INC.
Connect and lock coolant line (1).
Make sure that the coolant line (1) engages audibly.

Courtesy of BMW OF NORTH AMERICA, INC.
Insert and install the air conditioning compressor (3).

Tighten down screws (2).

TIGHTENING TORQUE SPECIFICATIONS

Air conditioning compressor in component carrier
M10	Tightening torque	38 Nm

Courtesy of BMW OF NORTH AMERICA, INC.

Connect and lock the connector (1).
Make sure the connector (1) engages audibly.
Insert and install the holder (2).

Tighten down screw (1).

TIGHTENING TORQUE SPECIFICATIONS

Holder for transmission oil lines on component earner
M6X16	Tightening torque	12 Nm

Courtesy of BMW OF NORTH AMERICA, INC.

Follow-up work

Refer to INSTALLING THE COOLANT LINE BETWEEN THE CYLINDER HEAD AND THE COOLANT PUMP .
Refer to INSTALLING THE ALTERNATOR .
Refer to INSTALLING THE THROTTLE BODY .
Refer to INSTALLING THE DRIVE BELT FOR ALTERNATOR .
Refer to INSTALLING CHARGE AIR LINE .
Refer to INSTALLING BOTTOM CLEAN AIR PIPE .
Refer to INSTALLING CLEAN AIR PIPE, TOP .
Refer to INSTALLING THE INTAKE FILTER HOUSING (TENSION STRUT REMOVED ON SHOCK TOWER) .
Refer to INSTALLING FAN COWL .
Refer to INSTALLING THE REAR TOP CROSS CONNECTION .
Refer to INSTALLING UPPER CROSS CONNECTION .
Refer to INSTALLING BOTH FRONT-END STRUTS .
Refer to INSTALLING THE CENTER ENGINE COMPARTMENT COVER .
Refer to FILLING THE HIGH-TEMPERATURE COOLING SYSTEM WITH THE VACUUM FILLING EQUIPMENT .
Refer to FILLING THE LOW-TEMPERATURE COOLING SYSTEM WITH THE VACUUM FILLING EQUIPMENT .
Refer to CONNECTING ALL BATTERY GROUND LEADS .
Refer to VENTING THE HIGH-TEMPERATURE COOLANT SYSTEM .
Refer to VENTING THE LOW-TEMPERATURE COOLING SYSTEM .
Refer to INSTALLING ACOUSTIC COVER .
Refer to INSTALLING THE FRONT BOTTOM LEFT AND RIGHT COVER .
Refer to INSTALLING THE UNDERBODY PROTECTION OF THE STEERING GEAR OR THE FRONT THRUST FIELD .
Refer to INSTALLING FRONT UNDERBODY PROTECTION .