Replace the crankshaft seal

WARNING: This page does not describe the selected car, but rather 7 other vehicles, including the 2025 BMW X4, 2024 BMW X4, 2023 BMW X4, 2022 BMW X4, and 2021 BMW X4. However, it is still accessible from the selected car via links, so may be relevant.

Preliminary work

Refer to DEACTIVATING ELECTRICAL SYSTEM .
Refer to REMOVING THE CENTER UNDERBODY PROTECTION .
Refer to REMOVING REAR UNDERBODY PROTECTION .
Refer to IF INSTALLED: REMOVING THE UNDERBODY PLANKING OF THE TRANSMISSION ON THE SIDE .
Refer to REMOVING TANK COVER ON LEFT AND RIGHT .
Refer to REMOVING THE CONNECTING SUPPORT FROM THE TUNNEL .
Refer to REMOVING EXHAUST SYSTEM .
Refer to REMOVING STARTER MOTOR .
Refer to REMOVING THE HEAT SHIELDS .
Refer to REMOVING THE RETAINING PLATES .
Refer to PARTIALLY LOOSENING THE PROP SHAFT .
Refer to REMOVING THE AUTOMATIC TRANSMISSION (ALL-WHEEL DRIVE VEHICLE) .
Refer to REMOVING FLYWHEEL .

Removing the rear crankshaft seal

Drill a hole at the crankshaft seal.

NOTE: Use the drill (1) with a maximum diameter of 2.5 mm.

Remove the shavings immediately with the vacuum cleaner. Do not remove shavings with compressed air!

Courtesy of BMW OF NORTH AMERICA, INC.
Screw in special tool 0 491 454 (23 0 490) in the arrow direction.
Drive out the crankshaft sealing ring with impact weight in the arrow direction.

Courtesy of BMW OF NORTH AMERICA, INC.

Replace crankshaft seal.
Parts: Crankshaft seal

Installing the rear crankshaft seal

NOTE: RISK OF DAMAGE
Radial shaft seal damage.
Taping the sealing lip (inner) and applying oil to the radial shaft seal will lead to its destruction.

Do not tap the sealing lip (inner) of the radial shaft seal.
Do not apply oil to the radial shaft seal.
Install the radial shaft seal dry.

Preassemble special tool 0 496 137 (11 8 815) on crankshaft.
Carefully slip the crankshaft sealing ring (1) straight off in a rotational movement using special tool 0 496 137 (11 8 815) until the crankshaft sealing ring is on and parallel to the timing case cover.

Courtesy of BMW OF NORTH AMERICA, INC.
Secure special tool 0 494 029 (11 9 182) to the crankshaft using special tool 0 494 031 (11 9 184) .

Courtesy of BMW OF NORTH AMERICA, INC.

Connect special tool 2 360 215 onto special tool 0 493 881 (11 9 180) .

Courtesy of BMW OF NORTH AMERICA, INC.
Carefully pull in the crankshaft sealing ring straight using special tool 0 494 028 (11 9 181) and 2 360 215 in combination with special tool 0 494 030 (11 9 183) .

Courtesy of BMW OF NORTH AMERICA, INC.
Tighten the crankshaft seal ring using the tool (1) till reaching the stop.

Courtesy of BMW OF NORTH AMERICA, INC.

Follow-up work

Refer to INSTALLING THE FLYWHEEL .
Refer to INSTALLING AUTOMATIC TRANSMISSION .
Refer to FASTENING THE PROP SHAFT (PARTIALLY REMOVED) .
Refer to INSTALLING THE RETAINING PLATES .
Refer to INSTALLING THE HEAT SHIELDS .
Refer to INSTALLING STARTER MOTOR .
Refer to INSTALLING EXHAUST SYSTEM .
Refer to INSTALLING THE CONNECTING SUPPORTS ON THE TUNNEL .
Refer to INSTALLING TANK COVER ON LEFT AND RIGHT .
Refer to INSTALLING THE UNDERBODY PLANKING OF THE TRANSMISSION ON THE SIDE .
Refer to INSTALLING UNDERBODY PROTECTION AT REAR .
Refer to INSTALLING THE CENTER UNDERBODY PROTECTION .
Refer to ACTIVATING ELECTRICAL SYSTEM .
Refer to CHECKING/TOPPING UP THE OIL LEVEL IN THE AUTOMATIC TRANSMISSION .