Install the sealing cap with radial shaft seal
NOTE:
RISK OF DAMAGE
For additional information see: OVERVIEW OF CONSUMABLES .
For additional information see: OVERVIEW OF CONSUMABLES .
- Apply the sealant (1) as shown on the special tool 2 469 803.
Parts: Sealant
SEALING COMPOUND SPECIFICATIONS
| Loctite 5970 liquid sealing compound Processing time <10 minutes at room temperature | 50 ml, Cartridge | 83190404517 |
- Clean sealing surfaces.
- Apply the sealing compound at the contact points (arrows) on the crankcase and oil pan.
- Check the fitting sleeves for damage and replace if necessary.
NOTE:
TECHNICAL INFORMATION
The work must be performed with vehicle care to prevent component damage.
The work must be performed with vehicle care to prevent component damage.
- Push the sealing cap (2) with the shaft seal and support ring (1) and abut (arrow).
NOTE:
TECHNICAL INFORMATION
The work must be performed with vehicle care to prevent component damage.
The work must be performed with vehicle care to prevent component damage.
- Counter-hold the sealing cap (2) with the shaft seal in the lower area (arrow).
- Install the support ring (1) on the camshaft.
- Slide the sealing cap (2)
with the upper shaft seal above the support ring (1)
and abut.
- Press on the casing (1) and remove the support ring (2) .
- Hand-tighten the bolts (1)
.
- Replace screws (1)
.
Parts: Screws
- Hand-tighten the bolts (1)
.
- Tighten down screws (1) .
TIGHTENING TORQUE SPECIFICATIONS
| Sealing cap with shaft seal to crankcase | ||
| Torx screw M6 | tightening torque | 10 Nm |
- Tighten down screws (1) .
TIGHTENING TORQUE SPECIFICATIONS
| Upper oil sump section to sealing cap | ||
| M8 Replace screws. |
tightening torque | 27 Nm |
Follow-up work
- Refer to INSTALLING THE FLYWHEEL .
- Refer to INSTALLING AUTOMATIC TRANSMISSION (ALL-WHEEL DRIVE VEHICLE) (GA8HP76Z) .
- Refer to INSTALLING THE TRANSFER BOX (ATC 13-1) .
- Refer to INSTALLING TRANSMISSION CROSS MEMBER .
- Refer to FASTENING THE PROP SHAFT (PARTIALLY REMOVED) .
- Refer to INSTALLING THE RETAINING PLATES .
- Refer to INSTALLING THE HEAT SHIELDS .
- Refer to INSTALLING EXHAUST SYSTEM .
- Refer to ACTIVATING ELECTRICAL SYSTEM .
- Refer to CHECKING/TOPPING UP THE OIL LEVEL IN THE AUTOMATIC TRANSMISSION .
- Refer to CHECKING/TOPPING UP THE TRANSFER BOX OIL .
- Refer to INSTALLING CENTER STIFFENING PLATE .
- Refer to INSTALLING TANK COVER ON LEFT AND RIGHT .
- Refer to INSTALLING REAR PANEL .
- Refer to PARTIALLY INSTALLING THE REAR LEFT AND RIGHT WHEEL ARCH COVERS .
- Refer to INSTALLING BOTH EXHAUST COVERS .
- Refer to INSTALLING BOTH SIDE REAR TRIM STRIPS .
- Refer to INSTALLING THE REAR BUMPER TRIM .
- Refer to INSTALLING THE REAR DIFFUSER .
- Refer to INSTALLING THE TAIL LIGHT ON THE LEFT AND RIGHT SIDE PANELS .
- Refer to INSTALLING COVER FOR WATER CHANNEL ON LEFT AND RIGHT .
- Refer to INSTALLING THE LUGGAGE COMPARTMENT WHEEL ARCH TRIM PANEL ON THE LEFT AND RIGHT (PARTIALLY REMOVED) .
- Refer to INSTALLING BOTH LEDS IN THE CARGO AREA .
- Refer to INSTALLING LOADING EDGE TRIM .
- Refer to INSTALLING LUGGAGE COMPARTMENT FLOOR COVERING .
- Refer to INSTALLING FRONT UNDERBODY PROTECTION .
- Refer to INSTALLING THE STIFFENING PLATE .
- Refer to INSTALLING UNDERBODY PROTECTION AT REAR .