Installing right exhaust turbocharger

• Loosen screws (2).
• Remove oil return line (1).
• Make sure that the sealing surfaces in the area of the oil return line (1) are flat and free of grease.
• Replace the seal (3).

  Parts:  Seal

  Courtesy of BMW OF NORTH AMERICA, INC.

• Replace the oil return line (3).

  Parts:  Oil return line

• Replace the seal (1).

  Parts:  Seal

• Replace screws (2).

  Parts:  Screws

• Position screws (2) in oil return line (3).
• Slide seal (1) onto the screws (2).

  Courtesy of BMW OF NORTH AMERICA, INC.

  NOTE: TECHNICAL INFORMATION 
  Complete the following steps with the help of a support person.
• Position the oil return line (1).
• Tighten screws (2) with an electronic torque wrench with tightening angle display.
  TIGHTENING TORQUE SPECIFICATION
  
  

  Oil return line at the exhaust turbocharger
  M6x16 Replace screws.	Joining torque	5 Nm
  	Angle of rotation	60°

  Courtesy of BMW OF NORTH AMERICA, INC.

• Make sure that the seal (3) does not fall out during the feed in.
• Check oil feed line for contamination or obstruction and clean or replace as needed.

  If the oil feed line is heavily contaminated, it is recommended to change the engine oil and oil filter.

• Check the clean air lines on the intake side and the charge air cooler for contamination or foreign bodies, and clean if necessary.
• If installed: Check the coolant feed lines and coolant return lines for the exhaust turbocharger for contamination or obstruction and clean or replace as needed.
• Check the screw connections and plug connections of all lines for accuracy.
• Check air cleaner for contamination and clean or replace as needed.
• Check correct functioning of crankcase ventilation.
• Replace all gaskets.

  Parts:  Seals

• Replace O-ring (1).

  Parts:  O-ring

• Make sure that the O-ring (1) does not fall into the oil duct in the engine block. 

  If the O-ring (1) cannot be disassembled, the oil return lid must be disassembled.

• Coat O-ring (1) with engine oil.
  ENGINE OIL SPECIFICATION
  
  

  Technically suitable engine oils for BMW Group engines

  Courtesy of BMW OF NORTH AMERICA, INC.

• Thread in exhaust turbocharger with oil return line in downward direction and position it.
• Make sure that the oil return line is not mechanically deformed. 
• Connect connectors (1) and lock.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Replace the V-clip (2).

  Parts:  V-band clamp

• Position V-clip (2).
• Hand-tighten the bolt (1).

  Courtesy of BMW OF NORTH AMERICA, INC.

• Position special tool 2 249 171 (2) on cylinder head covers.
• Tighten special tool 2 249 171 (2) with screws (1) on cylinder head covers. Note the screw length while doing so.
  TIGHTENING TORQUE SPECIFICATION
  
  

  Gauge of exhaust turbocharger to cylinder head cover
  screw	Tightening torque	10 Nm

  Courtesy of BMW OF NORTH AMERICA, INC.

• Manually move the screws (1) of the setting gauge up to the contact surface of the exhaust turbocharger (2).
• Exhaust turbocharger (2) must be aligned on vertical axis on left and right.
• Adjust exhaust turbocharger (2) parallel to setting gauge.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Tighten screw (1) on the V-clip.
  TIGHTENING TORQUE SPECIFICATION
  
  

  Exhaust turbocharger to exhaust manifold
  V-band clamp Replace V-band clamp.	Tightening torque	9 Nm
  	Tightening torque	20 Nm

  Courtesy of BMW OF NORTH AMERICA, INC.

• Check if the screw connection of the V-band clamp is too loose.
• If there is a gap between the ends of the V-band clamps: Loosen the screw and tighten again.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Check if the screw connection of the V-band clamp is too tight.
• When the ends of the V-band clamp are positioned one below the other: Loosen screws and retighten.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Make sure that the ends of the V-band clamp are parallel to each other.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Loosen screws (1).
• Remove special tool 2 249 171 (2).

  Courtesy of BMW OF NORTH AMERICA, INC.

• Tighten down screw (1).
  TIGHTENING TORQUE SPECIFICATION
  
  

  Oil return line to crankcase
  screw	Tightening torque	10 Nm

  Courtesy of BMW OF NORTH AMERICA, INC.

• Push hose clamps (1) onto hoses.
• Push the hoses onto the connections.
• Secure hose clamps (1).

  Courtesy of BMW OF NORTH AMERICA, INC.

• Replace the screw (1).

  Parts:  Screw

• Replace the sealing ring or sealing rings (2).

  Parts:  Sealing ring or sealing rings

• Make sure that when installing sealing rings without a fitting aid (bridge), both sealing rings are replaced. 
• Position screw (1) with the sealing ring or sealing rings (2) on the oil feed line.
• Position oil feed line.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Determining the screw type and selecting the appropriate socket wrench:

  Screw type	Matching socket wrench
  Hexagon screw (3)	Commercial socket wrench (1)
  Multi-tooth screw (4)	Multi-tooth socket wrench (2)

  Courtesy of BMW OF NORTH AMERICA, INC.

• Tighten screw (1) by hand.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Tighten screw (1) by hand.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Tighten down screw (2).
  TIGHTENING TORQUE SPECIFICATION
  
  

  Oil feed line holder to exhaust turbocharger
  M6x16 screw	Tightening torque	10 Nm

• Tighten down screw (1).

  Courtesy of BMW OF NORTH AMERICA, INC.

  TIGHTENING TORQUE SPECIFICATION
  
  

  Oil feed line to exhaust turbocharger
  Banjo bolt M10x1 Replace screw.	Joining torque	8 Nm
  	Angle of rotation	70°

Follow-up work 

• Refer to INSTALLING UPPER CATALYTIC CONVERTER NEAR ENGINE FOR BANK 2 .
• Refer to INSTALLING CATALYTIC CONVERTER NEAR THE ENGINE ABOVE CYLINDER BANK 1 .
• Refer to INSTALLING HEAT SHIELD, TOP .
• Refer to INSTALLING THE LAMBDA OXYGEN SENSOR FOR CYLINDERS 1 TO 4 .
• Refer to INSTALLING THE LAMBDA OXYGEN SENSOR FOR CYLINDERS 5 TO 8 .
• Refer to INSTALLING THE CROSSING OF THE TRANSMISSION WIRING HARNESS .
• Refer to INSTALLING THE COOLANT EXPANSION TANK FOR THE LOW-TEMPERATURE .
• Refer to INSTALLING ENGINE VENTILATION LINE OF CYLINDER BANK 1 .
• Refer to FASTENING THE ENGINE VENTILATION LINE OF CYLINDER BANK 1 .
• Refer to INSTALLING THE CLEAN AIR PIPE OF CYLINDER BANK 1 .
• Refer to INSTALLING BRACKET FOR RIGHT INTAKE SILENCER .
• Refer to INSTALLING OIL FILLER NECK .
• Refer to INSTALLING THE OXYGEN SENSOR MONITOR FOR CYLINDERS 1 TO 4 .
• Refer to INSTALLING RIGHT INTAKE SILENCER HOUSING .
• Refer to INSTALLING THE LEFT INTAKE SILENCER BRACKET .
• Refer to INSTALLING THE OXYGEN SENSOR MONITOR FOR CYLINDERS 5 TO 8 .
• Refer to FASTENING THE ACTIVATED-CHARCOAL FILTER LINE .
• Refer to INSTALLING THE ENGINE VENTILATION LINE OF CYLINDER BANK 2 .
• Refer to FASTENING THE ENGINE VENTILATION LINE OF CYLINDER BANK 2 .
• Refer to INSTALLING THE HEAT SHIELD OF THE CRANKCASE VENTILATION OF CYLINDERS 1 TO 4 .
• Refer to INSTALLING THE RIGHT-HAND CHARGE AIR COOLER .
• Refer to CLOSING THE LOW-TEMPERATURE COOLANT CIRCUIT .
• Refer to INSTALLING FRONT UNDERBODY PROTECTION .
• Refer to INSTALLING THE LOWER LEFT FRONT WHEEL ARCH COVER .
• Refer to INSTALLING FAN COWL .
• Refer to INSTALLING THE RIGHT UNFILTERED-AIR DUCT .
• Refer to INSTALLING OIL FILLER NECK .
• Refer to INSTALLING RIGHT INTAKE SILENCER HOUSING .
• Refer to INSTALLING THE LEFT UNFILTERED-AIR DUCT .
• Refer to INSTALLING LEFT INTAKE SILENCER HOUSING .
• Refer to INSTALLING THE REAR TOP CROSS CONNECTION .
• Refer to INSTALLING THE FRONT-END STRUT .
• Refer to INSTALLING UPPER CROSS CONNECTION .
• Refer to INSTALLING ACOUSTIC COVER .
• Refer to INSTALLING THE COVER IN THE ENGINE COMPARTMENT AT TOP LEFT AND RIGHT .
• Refer to FILLING THE LOW-TEMPERATURE COOLING SYSTEM WITH THE VACUUM FILLING EQUIPMENT .
• Refer to VENTING THE LOW-TEMPERATURE COOLING SYSTEM .