Remove headlining
WARNING:
Pyrotechnic components.
Danger! Immobilization period-threatening injuries!
Danger! Immobilization period-threatening injuries!
- All work on pyrotechnic parts may be carried out by technically experienced and appropriately trained personnel only.
- Replace any damaged part or ones that have been dropped.
- For additional information see: SAFETY REGULATIONS FOR HANDLING COMPONENTS WITH GAS GENERATORS .
NOTE:
RISK OF DAMAGE
Electrostatic discharge.
Damage to or destruction of electrical components.
Electrostatic discharge.
Damage to or destruction of electrical components.
- Leave the electrical components in their original packaging until they are being installed. Only use the original packaging for returning the product. Always package removed components straight away.
- Read and comply with user information on using the associated special tool 12 7 060.
- Only tap the housings of electrical components. Do not tap pins or multi-pin connectors directly.
- Wear electrically conductive clothing and antistatic shoes (with ESD symbol).
- For additional information see: NOTES ON ESD PROTECTION (ELECTRO STATIC DISCHARGE) .
NOTE:
RISK OF DAMAGE
Careless handling of tools and sharp-edged components.
Scratches, surface damage.
Careless handling of tools and sharp-edged components.
Scratches, surface damage.
- Protect working area.
- Handle tools and components carefully.
NOTE:
TECHNICAL INFORMATION
The following procedure forms the basis for these repair instructions and must be observed without fail.
For additional information see: GENERAL PROCEDURE FOR THE DISASSEMBLY AND INSTALLATION OF BONDED WINDOW GLASS .
The following procedure forms the basis for these repair instructions and must be observed without fail.
For additional information see: GENERAL PROCEDURE FOR THE DISASSEMBLY AND INSTALLATION OF BONDED WINDOW GLASS .
NOTE:
TECHNICAL INFORMATION
Perform window removal using the "spider".
For additional information see: REMOVING WINDOWS WITH A "SPIDER" .
Perform window removal using the "spider".
For additional information see: REMOVING WINDOWS WITH A "SPIDER" .
Preliminary work
- Refer to REMOVING THE LEFT AND RIGHT A-PILLAR TRIM PANEL .
- Refer to PARTIALLY REMOVING BOTH TOPPING B-PILLAR TRIM PANELS .
- Refer to REMOVING BOTH BACKREST SIDE SECTIONS .
- Refer to REMOVING THE LEFT AND RIGHT SEAT BELT FINISHER STRIP .
- Refer to REMOVING RIGHT C-PILLAR TRIM PANEL LEFT AND RIGHT .
- Refer to REMOVING INSIDE MIRROR .
- Refer to REMOVING THE KAFAS CAMERA .
- Refer to DISCONNECTING RAIN-LIGHT-SOLAR-CONDENSATION SENSOR .
- Refer to REMOVING THE HANDS-FREE MICROPHONE LEFT AND RIGHT .
- Refer to REMOVING BOTH SUN VISORS AND COUNTER SUPPORTS .
- Refer to REMOVING THE FRONT LEFT AND RIGHT VANITY MIRROR LIGHTS .
- Refer to REMOVING THE ROOF FUNCTION CENTER (FZD) .
- Refer to REMOVING THE REAR LEFT AND RIGHT HANDLE .
- Refer to REMOVING INTERIOR ROOF LIGHT .
- Refer to REMOVING THE COVER OF THE ENGINE COMPARTMENT AT THE REAR LEFT .
- Refer to REMOVING THE COVER OF THE REAR RIGHT ENGINE COMPARTMENT .
- Refer to REMOVING LEFT AND RIGHT WIPER ARM .
- Refer to REMOVING WINDSHIELD PANEL COVER .
- Refer to REMOVING THE WINDSHIELD .
NOTE:
Perform the steps on the right and left side.
- Remove expanding rivet (1) in the headlining (2) .
NOTE:
Perform the steps on the left and right side.
- Permanently cover the retaining plate (1)
before lowering the headlining with a suitable auxiliary material to protect the vehicle interior from damage.
- Release auxiliary brake light cover (1)
with the detent (2)
and the clips (3)
, then pull down to remove.
- Pull down to unclip the headlining (1)
and the clips (2)
.
- Unclip the headlining (2)
and the clips (1)
.
- With the help of another, remove headlining (1) through the cutout in the windshield.