Installing the left cylinder head

Replace the cylinder head gasket. See REPLACING THE CYLINDER HEAD GASKET .

Install the left cylinder head. See INSTALLING THE LEFT CYLINDER HEAD .

Follow-up work 

• Refer to INSTALLING THE EXHAUST CAMSHAFT ADJUSTER OF CYLINDERS 7 TO 12 .
• Refer to INSTALLING INTAKE ADJUSTER OF CYLINDERS 7 TO 12 .
• Refer to REPLACING THE CENTRAL BOLT .
• Refer to SECURING BOTH CENTRAL BOLTS OF THE VANOS GEAR .
• Refer to INSTALLING THE UPPER SLIDE RAIL .
• Refer to INSTALLING SPECIAL TOOL TO PRE-TENSIONING TIMING CHAIN .
• Refer to SECURING THE CENTRAL BOLT OF THE VARIABLE CAMSHAFT TIMING CONTROL OF THE INTAKE .
• Refer to SECURING THE CENTRAL BOLT OF THE VARIABLE CAMSHAFT TIMING CONTROL OF THE EXHAUST .
• Refer to REMOVING THE SPECIAL TOOLS TO FIX THE CAMSHAFTS .
• Refer to REMOVING THE SPECIAL TOOLS TO DISCONNECTING THE CRANKSHAFT .
• Refer to CHECKING TIMING .
• Refer to REMOVING THE SPECIAL TOOLS TO DISCONNECTING THE CRANKSHAFT .
• Refer to REMOVING SPECIAL TOOL TO PRETENSION TIMING CHAIN .
• Refer to INSTALLING THE HYDRAULIC CHAIN TENSIONER .
• Refer to INSTALLING THE TOP TIMING CASE COVER OF CYLINDERS 7 TO 12 .
• Refer to INSTALLING BOTH SOLENOID VALVES ON THE LEFT .
• Refer to INSTALLING LEFT CLEAN AIR PIPE .
• Refer to INSTALLING ALTERNATOR 2 .
• Refer to INSTALLING THE HEATER RETURNING HOSE ON THE COOLANT PUMP .
• Refer to INSTALLING THE LEFT COOLANT HOSE ON THE RADIATOR .
• Refer to CONNECTING THE COOLANT HOSE TO THE AUXILIARY COOLANT PUMP .
• Refer to MOUNTING AIR CONDITIONING COMPRESSOR .
• Refer to INSTALLING THE BELT PULLEY .
• Refer to INSTALLING THE DRIVE BELT FOR ALTERNATOR .
• Refer to INSTALLING THE DRIVE BELT FOR ALTERNATOR 2 AND THE AIR CONDITIONING COMPRESSOR .
• Refer to REMOVING THE PROTECTIVE PLATE AT THE RADIATOR .
• Refer to INSTALLING THE LEFT CYLINDER HEAD COVER .
• Refer to ATTACHING COOLANT LINE FOR LEFT TURBOCHARGER .
• Refer to REMOVING TRANSMISSION CROSS-MEMBER .
• Refer to REMOVING THE TRANSFER BOX (ATC 13-1) .
• Refer to INSTALLING THE CATALYTIC CONVERTER FOR CYLINDERS 7 TO 12 .
• Refer to INSTALLING THE TRANSFER BOX (ATC 13-1) .
• Refer to SECURING THE JUNCTURE SHAFT IN FRONT ON THE FRONT AXLE DIFFERENTIAL .
• Refer to INSTALLING TRANSMISSION CROSS MEMBER .
• Refer to CHECKING/TOPPING UP THE TRANSFER BOX OIL (ACTIVE TORQUE CONTROL 13-1) .
• Refer to FASTENING THE PROP SHAFT (PARTIALLY REMOVED) .
• Refer to INSTALLING THE HEAT SHIELDS .
• Refer to CONNECTING TRANSMISSION OIL LINES .
• Refer to INSTALLING THE RETAINING PLATES .
• Refer to INSTALLING EXHAUST SYSTEM .
• Refer to INSTALLING THE CONNECTING SUPPORTS ON THE TUNNEL .
• Refer to INSTALLING REAR UNDERBODY PROTECTION .
• Refer to INSTALLING BOTH TRIM PIECES FOR THE EXHAUST TAILPIPE .
• Refer to INSTALLING THE TRIM ON THE REAR BUMPER PANEL .
• Refer to INSTALLING THE REAR DIFFUSER .
• Refer to INSTALLING THE LEFT LAMBDA OXYGEN SENSOR .
• Refer to INSTALLING THE UNIVERSAL JOINT AT THE BOTTOM OF THE STEERING SHAFT .
• Refer to CONNECTING THE COOLANT HOSE TO THE RADIATOR .
• Refer to INSTALLING THE ACTIVE STABILIZER IN FRONT .
• Refer to SECURING THE ANTI-ROLL BAR LINK ON THE LEFT AND RIGHT TO THE ANTI-ROLL BAR .
• Refer to INSTALLING THE COVER OF THE STEERING ASSEMBLY ON THE RIGHT .
• Refer to INSTALLING THE FRONT RIGHT WHEEL .
• Refer to RELEASING THE OIL FILTER COVER .
• Refer to INSTALLING THE OIL FILTER ELEMENT .
• Refer to TIGHTENING THE OIL FILTER CAP .
• Refer to INSTALLING THE STIFFENING PLATE .
• Refer to INSTALLING THE UNDERBODY PROTECTION OF THE STEERING GEAR OR THE FRONT THRUST FIELD .
• Refer to INSTALLING THE FRONT UNDERBODY PROTECTION OR FRONT THRUST FIELD .
• Refer to PREPARING THE INJECTOR FOR INSTALLATION .
• Refer to INSTALLING INJECTORS .
• Refer to INSTALLING THE LEFT HIGH PRESSURE PUMP .
• Refer to INSTALLING THE HIGH-PRESSURE RAIL ON THE LEFT .
• Refer to INSTALLING ALL HIGH PRESSURE LINES BETWEEN THE RAIL AND THE INJECTORS .
• Refer to INSTALLING FUEL DELIVERY LINE .
• Refer to INSTALLING THE LEFT-HAND HIGH PRESSURE LINE BETWEEN THE HIGH PRESSURE PUMP AND THE RAIL .
• Refer to INSTALLING CHARGE AIR PIPE ON LEFT .
• Refer to INSTALLING TOPPING CLEAN AIR PIPE ON LEFT .
• Refer to PARTIALLY FASTENING THE WIRING HARNESS ON THE LEFT CYLINDER HEAD COVER .
• Refer to INSTALLING THE HOLDER FOR THE DME CONTROL UNIT ON THE LEFT .
• Refer to INSTALLING THE DME CONTROL UNIT FOR CYLINDERS 7 TO 12 .
• Refer to INSTALLING COVER FOR THE LEFT DME CONTROL UNIT .
• Refer to INSTALLING THE IGNITION COILS .
• Refer to INSTALLING THE LEFT-HAND VENTILATION LINE .
• Refer to INSTALLING THE INTAKE PLENUM .
• Refer to INSTALLING THE TANK VENT LINE .
• Refer to INSTALLING THE ENGINE VENTILATION LINE ON THE INTAKE SYSTEM .
• Refer to INSTALLING FAN COWL .
• Refer to INSTALLING THE REAR TOP CROSS CONNECTION .
• Refer to MOUNTING THE LEFT-HAND CHARGE AIR COOLER .
• Refer to INSTALLING THE LEFT THROTTLE BODY .
• Refer to INSTALLING LEFT INTAKE PORT .
• Refer to INSTALLING THE LEFT-HAND AIR DUCT .
• Refer to INSTALLING LEFT INTAKE SILENCER HOUSING .
• Refer to MOUNTING THE RIGHT-HAND CHARGE AIR COOLER .
• Refer to INSTALLING THE RIGHT THROTTLE BODY .
• Refer to INSTALLING RIGHT AIR DUCT .
• Refer to INSTALLING RIGHT INTAKE SILENCER HOUSING .
• Refer to INSTALLING TENSION STRUT ON SHOCK TOWER .
• Refer to INSTALLING WINDSHIELD PANEL COVER .
• Refer to INSTALLING THE CENTER COWL UPPER PART .
• Refer to INSTALLING THE FRONT HOOD SEAL AT THE REAR .
• Refer to INSTALLING THE REAR RIGHT ENGINE COMPARTMENT COVER .
• Refer to INSTALLING THE COVER OF THE ENGINE COMPARTMENT ON THE REAR LEFT .
• Refer to INSTALLING LEFT AND RIGHT WIPER ARM .
• Refer to INSTALLING FANFARE HORN, RIGHT .
• Refer to INSTALLING THE FANFARE ON THE LEFT SIDE .
• Refer to INSTALLING THE CENTER TOP CROSS CONNECTION .
• Refer to INSTALLING BOTH HEADLIGHTS .
• Refer to INSTALLING BUMPER COVER, FRONT .
• Refer to INSTALLING FRONT SECTION OF THE FRONT WHEEL ARCH COVER (PARTIALLY REMOVED) .
• Refer to INSTALLING FRONT ORNAMENTAL GRILLE .
• Refer to INSTALLING THE COVER OF THE ENGINE COMPARTMENT CENTER .
• Refer to TOPPING UP THE MOTOR OIL .
• Refer to INSTALLING ACOUSTIC COVER .
• Refer to CONNECTING ALL BATTERY GROUND LEADS .
• Refer to FILLING THE COOLING SYSTEM WITH THE VACUUM FILLING UNIT .
• Refer to FILLING THE LOW-TEMPERATURE COOLING SYSTEM WITH THE VACUUM FILLING EQUIPMENT .
• Refer to CHECKING/TOPPING UP THE OIL LEVEL IN THE AUTOMATIC TRANSMISSION .
• Refer to VENTING THE HIGH-TEMPERATURE COOLANT SYSTEM .
• Refer to VENTING THE LOW-TEMPERATURE COOLING SYSTEM .
• Refer to TAKING HOOD OUT OF THE SERVICE POSITION .
• Refer to ADJUSTING HEADLIGHTS .