LEMON Manuals: Even more car manuals for everyone
Home >> BMW >> 2014 >> M6 2D Convertible, Standard Trans >> Repair and Diagnosis >> External Pages >> Different car >> Section 1122 (Engine - Oil Pan, Crankshaft Seal, Timing Case Cover, Crankcase Ventilation System - Repair) >> Crankshaft Seal, Timing Case Cover >> N55 Hybrid Engine >> 11 14 151 Replacing transmission-side crankshaft seal (N55 Hybrid)

11 14 151 Replacing transmission-side crankshaft seal (N55 Hybrid)

WARNING: This page does not describe the selected car, but rather 50 other vehicles, including the 2016 BMW M5, 2016 BMW ActiveHybrid 5, 2016 BMW 550i xDrive, 2016 BMW 550i, and 2016 BMW 535i xDrive. However, it is still accessible from the selected car via links, so may be relevant.

Special tools required: 

WARNING:

High-voltage hazard!

The following must be strictly observed prior to starting work  :

Necessary preliminary work: 

IMPORTANT: Magnet wheel (1) is magnetic.
Keep magnet wheel (1) in a plastic bag away from metallic debris.

Remove magnet wheel (1) from crankshaft.

Fig 1: Identifying Magnet Wheel On Crankshaft
G09919841Courtesy of BMW OF NORTH AMERICA, INC.

Release screw on pulse sensor (1).

Slide PULSE SENSOR (2) upwards.

Fig 2: Identifying Pulse Sensor And Screw
G09919842Courtesy of BMW OF NORTH AMERICA, INC.
IMPORTANT: Drill size maximum 2, 5 mm. Remove metallic debris immediately.
Drill a hole with a drill (1) in the radial shaft seal (see arrow).
Fig 3: Drilling Hole In Radial Shaft Seal
G09919843Courtesy of BMW OF NORTH AMERICA, INC.
IMPORTANT: Immediately carefully remove metallic debris on the radial shaft seal (1).
Fig 4: Removing Metal Shavings After Drilling
G09919844Courtesy of BMW OF NORTH AMERICA, INC.

Screw in special tool 23 0 490 in direction of arrow.

Drive out radial shaft seal with impact weight in direction of arrow.

IMPORTANT: Immediately carefully remove residual metallic debris.
Fig 5: Driving Out Radial Shaft Seal With Impact Weight
G09919845Courtesy of BMW OF NORTH AMERICA, INC.

Prepare radial shaft seal (1) on special tool 11 8 220 .

Fig 6: Identifying Radial Shaft Seal On Special Tool 11 8 220
G09919846Courtesy of BMW OF NORTH AMERICA, INC.

Position the radial shaft seal (1) with special tool 11 8 220 on the crankshaft.

Fig 7: Positioning Radial Shaft Seal On Crankshaft
G09919847Courtesy of BMW OF NORTH AMERICA, INC.

Brush radial shaft seal (1) over the special tool 11 8 220 .

Move radial shaft seal (1) parallel up against the crankcase.

Fig 8: Identifying Radial Shaft Seal Parallel Up Against Crankcase
G09919848Courtesy of BMW OF NORTH AMERICA, INC.

Fasten special tool 11 9 182 with special tool 11 9 184 on the crankshaft.

Fig 9: Fastening Special Tools On Crankshaft
G09919849Courtesy of BMW OF NORTH AMERICA, INC.

Installation note: 

Prepare special tool 11 9 181 for installation.

Connect special tool 11 9 185 onto special tool 11 9 181 .

Fig 10: Connecting Special Tool 11 9 185 Onto Special Tool 11 9 181
G09919850Courtesy of BMW OF NORTH AMERICA, INC.

Pull on radial shaft seal with special tool 11 9 181 and 11 9 185 in combination with special tool 11 9 183 .

Fig 11: Pulling On Radial Shaft Seal Using Special Tools
G09919851Courtesy of BMW OF NORTH AMERICA, INC.

Screw on radial shaft seal with special tool 11 9 183 to limit position.

Fig 12: Screwing On Radial Shaft Seal To Limit Position
G09919852Courtesy of BMW OF NORTH AMERICA, INC.

Remove all special tools.

Assemble engine.

scientia non olet · About LEMON Manuals