Transmission, Removing, AUDI Q3
Special tools and workshop equipment required
- Pry Lever: 80-200
- Transmission Support: 3282
- Transmission Support - Pins 29: 3282/29
- Transmission Support - Mounting Plate 42A: 3282/42A
- Engine Bung Set: VAS6122
- Engine and Gearbox Jack: VAS6931
- Hose Clamps - Up To 25 mm: 3094
Procedure
- Pay attention to the general information. Refer to GENERAL INFORMATION .
- Follow the guidelines for clean working conditions. Refer to GUIDELINES FOR CLEAN WORKING CONDITIONS .
- Pay attention to the general repair information. Refer to GENERAL REPAIR INFORMATION .
- Bring all cable ties back to the same positions during installation.
-- Move the selector lever into "P" position.
-- Engage the parking brake.
-- Switch the ignition off.
-- Remove the noise insulation. Refer to OVERVIEW - NOISE INSULATION .
-- Remove the air filter housing. Refer to AIR FILTER HOUSING, REMOVING AND INSTALLING [CNTC, CYFB] or AIR FILTER HOUSING, REMOVING AND INSTALLING [DAZA, DNWA] .
-- Remove the battery tray. Refer to the appropriate Service Information .
-- Clamp off the coolant hoses on the transmission fluid cooler using the : 3094 .
-- Place a cloth underneath to catch any leaking coolant.
-- Loosen the hose clamps -arrows- and remove the coolant hoses from the transmission fluid cooler.
-- Seal the open lines and connections with clean plugs from the : VAS6122 .
-- If equipped, remove the bolts -1- and move the Transmission Coolant Valve -N488- to the side.
-- Disconnect the connector -2-, if equipped.
Risk of destroying due to electrostatic charge.
- Do not touch the connector terminals.
- Touch a grounded object (for example the hoist) and discharge any static electricity.
-- Turn the twist lock counter-clockwise -arrow- to disconnect the connector -1- for the Dual-Clutch Transmission Mechatronic -J743-.
-- Remove the starter. Refer to STARTER, REMOVING AND INSTALLING .
-- Remove the nuts -arrows- and remove the front bracket from the transmission fluid pan.
-- Remove all of the bolts for the transmission/engine connection that are accessible from above.
- The screw -3- is located in the opening for the starter.
-- Remove the subframe without the steering gear. Refer to SUBFRAME WITHOUT STEERING GEAR, REMOVING AND INSTALLING .
-- Support the engine in the installation position. Refer to ENGINE, SUPPORTING IN INSTALLATION POSITION .
-- If equipped, loosen the nut -3- and remove the ground wire -B-.
-- Remove the bolts -1 and 2- and remove the transmission support -A-.
-- Lower the engine/transmission assembly using the : 10-222A/11 until the dimension -a- is reached between the transmission housing and the transmission mount.
- Dimension -a- = maximum 65 mm.
-- Remove the nuts -arrows- and remove the right drive axle heat shield. (different versions)
-- Remove the left and right drive axle -arrow- from the transmission. Refer to DRIVE AXLE, REMOVING AND INSTALLING .
-- Tie up the drive axles to the rear.
- Make sure that the drive axle protective coating is not damaged.
-- Remove the bolts -1- from the cable bracket.
Risk of damaging the operating cable by deforming it.
- Never bend the operating cable too sharply or kink it.
-- Remove the lock washer -3- in direction of -arrow- and remove the selector lever cable from the transmission.
The : 3282 is set up with the : 3282/42A to remove the dual clutch transmission 0D9.
-- Place the : 3282 on the : VAS6931 .
-- Align the transmission support arms so that they match up with the holes in the : 3282/42A .
-- Install the support elements as shown on the : 3282/42A The "retaining plate with hole" is used as a front support element.
-- Place the : VAS6931 under the vehicle.
- The arrow symbol on the mounting plate points in the direction of travel.
-- Align the : 3282 so that it is parallel to the transmission.
-- Install the : 3282/29 in the transmission.
-- Attach the "retaining plate with hole" securely to the transmission as shown -arrow-.
-- Insert the last support element into the transmission as shown.
-- Support the transmission from underneath using the : VAS6931 .
-- Remove the remaining bolts for the transmission/engine connection.
-- Remove the transmission from the alignment sleeves.
-- Remove the transmission from the engine.
-- Lower the transmission carefully using the : VAS6931 .
-- When lowering, change the transmission position using the spindles on the : 3282 .