LEMON Manuals: Even more car manuals for everyone
Home >> Volkswagen >> 2006 >> GTI 1.8 E, Automatic >> Repair and Diagnosis >> External Pages >> Different car >> Section 267 (2.5L - Crankshaft, Cylinder Block - Engine Code(S): BGP, BGQ, CBTA & CBUA) >> 13 Crankshaft, Cylinder Block >> Description And Operation >> Ribbed Belt Drive Overview

Ribbed Belt Drive Overview

WARNING: This page is about a different car, the 2009 Volkswagen Rabbit, 2008 Volkswagen Rabbit, 2007 Volkswagen Rabbit, and 2006 Volkswagen Rabbit. However, it is still accessible from the selected car via links, so may be relevant.
Fig 1: Ribbed Belt Drive Overview
GWWN13-10287Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.
  1. Bolt
    • 25 Nm
  2. Bolt
    • 25 Nm
  3. Generator
    • Removing and installing, refer to Removal and Installation .
    • To make it easier to position the generator, drive the threaded bushing for the generator bolt back slightly.
  4. Bolt
    • 25 Nm
  5. Lower Idler Pulley with Bracket
    • For the Air Conditioning (A/C) compressor ribbed belt
    • Do not remove the pulley.
  6. Bolt
    • 25 Nm
  7. A/C Compressor
  8. Bolt
    • 25 Nm
  9. Coolant Pump
    • In the cylinder block.
    • Removing and installing, refer to COOLANT PUMP .
  10. Ribbed Belt, Generator, Power Steering Pump and Coolant Pump
    • Belt routing, refer to Fig 2.
    • Before removing, mark the rotation direction using chalk or a felt tip pen.
    • Check for wear.
    • Do not kink.
    • Removing and installing, refer to RIBBED BELT .
  11. Ribbed Belt, A/C Compressor
    • Belt routing, refer to Fig 2.
    • Before removing, mark the rotation direction using chalk or a felt tip pen.
    • Check for wear.
    • Do not kink.
    • Removing and installing, refer to RIBBED BELT .
  12. Vibration Damper
    • There are different versions
    • To remove and install, lock secure the crankshaft. Refer to CRANKSHAFT, LOCKING .
  13. Bolts
    • 50 Nm + an additional 90° (1/4) turn.
    • Always replace.
    • Use a strength category 10.9 bolt only.
    • Quantity: 5
  14. Bushing
    • Quantity: 2
  15. Belt Tensioner, A/C Compressor
  16. Belt Tensioner, Generator, Power Steering Pump and Coolant Pump
  17. Bolt
    • 25 Nm
  18. Bolt
    • 8 Nm
  19. Upper Idler Pulley with Bracket
    • For the generator, power steering pump and coolant pump ribbed belt.
    • Do not remove the pulley.
  20. Bolt
    • 40 Nm + an additional 90° (1/4) turn.
  21. Engine Mount
  22. Bushing
    • Quantity: 2
  23. Accessory Bracket
Fig 2: Ribbed Belt Routing
GWWN13-10243Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.
  1. Upper idler pulley
  2. Generator
  3. Lower idler pulley
  4. Ribbed belt, generator, power steering pump and coolant pump
  5. A/C compressor
  6. Ribbed belt, A/C compressor
  7. Vibration Damper
  8. Belt tensioner, A/C compressor ribbed belt
  9. Belt tensioner, generator, power steering pump and coolant pump ribbed belt
  10. Coolant pump
scientia non olet · About LEMON Manuals