LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2024 >> Corolla LE >> Repair and Diagnosis >> External Pages >> Different car >> Section 162 (Engine Mechanical System - Service Information (2 Of 3)) >> Engine Unit >> Removal [09/2022 - 11/2022] >> Procedure

Removal [09/2022 - 11/2022]: Procedure

WARNING: This page is about a different car, the 2025 Toyota GR Corolla, 2024 Toyota GR Corolla, and 2023 Toyota GR Corolla. However, it is still accessible from the selected car via links, so may be relevant.
  1. REMOVE COMPRESSOR ASSEMBLY WITH PULLEY 

    Refer to PROCEDURE - Step 8

  2. REMOVE FUEL TUBE SUB-ASSEMBLY 
    1. Disengage the clamp.
      GTY1106912Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the fuel tube sub-assembly from the fuel pipe sub-assembly.

      Refer to PRECAUTION [09/2022 - 11/2022]

  3. REMOVE NO. 2 AIR HOSE 
    1. Loosen the hose clamp and remove the No. 2 air hose from the turbocharger sub-assembly.
      GTY1019805Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  4. REMOVE NO. 6 WATER BY-PASS HOSE 
    1. Slide the 2 clips and separate the No. 6 water by-pass hose.
      GTY1106911Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disengage the clamp and remove the No. 6 water by-pass hose from the No. 1 water hose clamp bracket.
  5. REMOVE NO. 5 WATER BY-PASS HOSE 
    1. Slide the 2 clips and separate the No. 5 water by-pass hose.
      GTY1020464Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the bolt and No. 5 water by-pass hose from the crankshaft bearing cap.
  6. REMOVE NO. 3 VACUUM TRANSMITTING HOSE 
    1. Disengage the 2 clamp and remove the No. 3 vacuum transmitting hose.
      GTY1019819Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  7. REMOVE NO. 1 TURBO WATER HOSE 
    1. Slide the 2 clips and remove the No. 1 turbo water hose.
      GTY1019813Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  8. REMOVE NO. 1 WATER BY-PASS PIPE 
    1. Slide the clip and separate the No. 1 water by-pass pipe.
      GTY1019816Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the bolt, nut and No. 1 water by-pass pipe.
  9. REMOVE NO. 3 WATER BY-PASS PIPE 
    1. Remove the bolt and separate the No. 3 water by-pass pipe.
      GTY1019772Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Slide the clip and remove the No. 3 water by-pass pipe.
  10. REMOVE NO. 4 WATER BY-PASS PIPE 
    1. Remove the 3 bolts and separate the No. 4 water by-pass pipe.
      GTY1019825Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Slide the clip and remove the No. 4 water by-pass pipe.
  11. REMOVE WATER BY-PASS HOSE ASSEMBLY 
    1. Disengage the clamp.
      GTY1019826Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Slide the 2 clips and remove the water by-pass hose assembly.
  12. REMOVE E.F.I. VACUUM SENSOR ASSEMBLY (MANIFOLD ABSOLUTE PRESSURE SENSOR) 

    Refer to PROCEDURE - Step 2

  13. REMOVE VACUUM SENSOR ASSEMBLY 

    Refer to PROCEDURE - Step 3

  14. REMOVE INTAKE AIR PIPE 
    1. Separate the No. 1 vacuum transmitting hose.
      GTY1019821Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Separate the No. 2 vacuum transmitting hose.
    3. Separate the ventilation hose.
    4. Remove the e3 bolts.
    5. Loosen the hose clamp and remove the intake air pipe from the.
      GTY1019823Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  15. REMOVE ENGINE HANGER BRACKET 
    1. Remove the 2 bolts and engine hanger bracket from the cylinder head sub-assembly.
      GTY1019828Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  16. REMOVE DRIVE SHAFT BEARING BRACKET 
    1. Remove the 3 bolts and drive shaft bearing bracket from the cylinder block sub-assembly.
      GTY1019829Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  17. REMOVE NO. 4 CYLINDER BLOCK INSULATOR 
    1. Remove the 2 bolts and No. 4 cylinder block insulator.
      GTY1106910Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  18. REMOVE NO. 1 TURBO INSULATOR 

    Refer to PROCEDURE - Step 4

  19. REMOVE TURBOCHARGER SUB-ASSEMBLY 
    1. GTY1019937Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Remove the 2 bolts and separate the outlet turbo oil pipe.

    2. Remove the inlet turbo oil pipe union bolt.
    3. Remove the 2 bolts and separate the No. 1 turbo water pipe sub-assembly.
    4. Remove the 7 nuts, collar and turbocharger sub-assembly from the cylinder head sub-assembly.
  20. REMOVE EXHAUST MANIFOLD TO HEAD GASKET 

    Refer to PROCEDURE - Step 12

  21. REMOVE NO. 2 TURBO INSULATOR 
    1. Remove the 2 bolts and No. 2 turbo insulator from the cylinder brock sub-assembly.
      GTY1019939Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  22. REMOVE PURGE VALVE (PURGE VSV) 

    Refer to PROCEDURE - Step 4

  23. SEPARATE NO. 6 ENGINE WIRE 
    1. Disengage the 5 clamps and separate the No. 6 engine wire.
      GTY1019936Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  24. REMOVE NO. 2 ENGINE COVER BRACKET 
    1. Remove the bolt and No. 2 engine cover bracket from the intake manifold.
      GTY1020490Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  25. REMOVE INTAKE MANIFOLD 
    1. Remove the 3 bolts and 2 nuts and intake manifold from the cylinder head sub-assembly.
      GTY1251735Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Slide the clip and disconnect the No. 2 water by-pass hose to from the water by-pass connector.
  26. REMOVE NO. 1 VENTILATION FLANGE SEPARATOR 

    Refer to PROCEDURE - Step 17

  27. REMOVE NO. 1 INTAKE MANIFOLD TO HEAD GASKET 

    Refer to PROCEDURE - Step 18

  28. REMOVE WATER BY-PASS PIPE 
    1. Remove the bolt and nut.
      GTY1019943Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Slide the clip and remove the water by-pass pipe from the water inlet with thermostat sub-assembly.
  29. REMOVE NO. 7 ENGINE WIRE 
    1. Disengage the clamp.
      GTY1252482Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disconnect the connector and remove the No. 7 engine wire.
  30. REMOVE FUEL TUBE SUB-ASSEMBLY 
    1. Remove the fuel pipe clamp from the fuel tube connector.
      GTY1020491Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the bolt.
      GTY1019944Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Remove the fuel tube sub-assembly.

      Refer to PRECAUTION [09/2022 - 11/2022]

  31. REMOVE OIL LEVEL GAGE SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 11

  32. REMOVE OIL LEVEL GAGE GUIDE 

    Refer to PROCEDURE - Step 12

  33. REMOVE FUEL DELIVERY GUARD 

    Refer to PROCEDURE - Step 13

  34. REMOVE NO. 1 DELIVERY PIPE SPACER 
    1. Remove the 2 No. 1 delivery pipe spacers.
  35. REMOVE FUEL DELIVERY PIPE 

    Refer to PROCEDURE - Step 14

  36. REMOVE FUEL DELIVERY SPACER 

    Refer to PROCEDURE - Step 15

  37. REMOVE INJECTOR VIBRATION INSULATOR 

    Refer to PROCEDURE - Step 16

  38. REMOVE NO. 1 FUEL PIPE SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 18

  39. REMOVE FUEL PUMP ASSEMBLY 

    Refer to PROCEDURE - Step 21

  40. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 9

  41. REMOVE NO. 6 ENGINE WIRE 

    Refer to PROCEDURE - Step 10

  42. REMOVE DIRECT FUEL INJECTOR ASSEMBLY 

    Refer to PROCEDURE - Step 11

  43. REMOVE FUEL INJECTOR SEAL 

    Refer to PROCEDURE - Step 12

  44. REMOVE NO. 2 CYLINDER BLOCK INSULATOR 
    1. Remove the No. 2 cylinder block insulator from the cylinder block sub-assembly.
      GTY1019932Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  45. REMOVE SENSOR WIRE 
    1. Remove the 2 bolts and remove the sensor wire from the cylinder block sub-assembly.
      GTY1019962Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  46. REMOVE VENTILATION HOSE 
    1. Disengage the clamp.
      GTY1019963Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Slide the clip and remove the ventilation hose from the cylinder head cover sub-assembly.
  47. REMOVE VACUUM REGULATING VALVE ASSEMBLY 
    1. Remove the 2 bolts and vacuum regulating valve assembly from the cylinder head cover sub-assembly.
      GTY1020495Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  48. REMOVE IGNITION COIL ASSEMBLY 

    Refer to PROCEDURE - Step 2

  49. REMOVE ENGINE COVER JOINT 
    1. Remove the 2 engine cover joints from the cylinder head cover sub-assembly.
      GTY1019960Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  50. REMOVE ENGINE COVER BRACKET 
    1. Remove the bolt and engine cover bracket from the No. 1 vacuum pump bracket.
      GTY1019965Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  51. REMOVE FUEL HOSE BRACKET 
    1. Remove the 2 bolts and fuel hose bracket form the cylinder head cover sub-assembly.
      GTY1019966Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  52. REMOVE INTAKE PIPE OR HOSE STAY 
    1. Remove the 3 bolts and intake pipe or hose stay from the cylinder head cover sub-assembly.
      GTY1020496Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  53. REMOVE NO. 3 CYLINDER BLOCK INSULATOR 
    1. Remove the No. 3 cylinder block insulator from the cylinder block sub-assembly.
      GTY1019964Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
scientia non olet · About LEMON Manuals