- INSTALL INSTRUMENT PANEL CUSHION
- Clean the instrument panel safety pad sub-assembly surface.
- Remove any remaining double-sided tape from the instrument panel safety pad sub-assembly.
- Wipe off any tape adhesive residue with cleaner.
- Remove the release paper from a new instrument panel cushion.
HINT:
After removing the release paper, keep the exposed adhesive free from foreign matter.
- Install the instrument panel cushion as shown in the illustration.
 Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
|
| *a |
Edge of Curved Surface |
| *b |
Outline |
- INSTALL NO. 1 INSTRUMENT PANEL PIN
- Install the 4 No. 1 instrument panel pins with the 4 screws <C>.
 Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
|
- INSTALL INSTRUMENT PANEL HOLE COVER (w/ Headup Display)
- Engage the 3 guides.
 Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
|
- Engage the 5 claws to install the instrument panel hole cover.
 Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
|
- INSTALL NO. 1 DEFROSTER NOZZLE GARNISH
- Engage the 5 guides.
 Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
|
- Engage the 4 clips to install the No. 1 defroster nozzle garnish.
 Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
|
- INSTALL NO. 2 METER BRACKET SUB-ASSEMBLY (w/ Headup Display)
- Install the No. 2 meter bracket sub-assembly with the screw <C>.
 Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
|
- INSTALL NO. 1 METER BRACKET SUB-ASSEMBLY
- Install the No. 1 meter bracket sub-assembly with the screw <C>.
 Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
|
- INSTALL RADIO TUNER FINISH RETAINER
- Install the radio tuner finish retainer with the 5 screws <C>.
 Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
|
- INSTALL NO. 3 INSTRUMENT PANEL WIRE
- Engage the clamp to install the No. 3 instrument panel wire.
 Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
|
- INSTALL AUTOMATIC LIGHT CONTROL SENSOR
Refer to PROCEDURE - Step 1
- INSTALL ANTENNA CORD SUB-ASSEMBLY (w/o Navigation System)
Refer to PROCEDURE - Step 4
- INSTALL NAVIGATION ANTENNA ASSEMBLY WITH BRACKET (w/ Navigation System)
Refer to PROCEDURE - Step 3
- INSTALL ANTENNA CORD SUB-ASSEMBLY (w/ Navigation System)
Refer to PROCEDURE - Step 1
- INSTALL TELEPHONE AND GPS ANTENNA ASSEMBLY WITH BRACKET (w/ Manual (SOS) Switch)
Refer to PROCEDURE - Step 3
- INSTALL TELEPHONE AND GPS ANTENNA CORD (w/ Manual (SOS) Switch)
Refer to PROCEDURE - Step 1
- INSTALL NO. 3 HEATER TO REGISTER DUCT SUB-ASSEMBLY
- Install the No. 3 heater to register duct sub-assembly with the 2 screws <C>.
 Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
|
- INSTALL NO. 1 HEATER TO REGISTER DUCT SUB-ASSEMBLY
- Install the No. 1 heater to register duct sub-assembly with the 2 screws <C>.
 Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
|
- INSTALL METER MIRROR SUB-ASSEMBLY (w/ Headup Display)
Refer to PROCEDURE - Step 1
- INSTALL DEFROSTER NOZZLE ASSEMBLY
- Install the defroster nozzle assembly with the 3 screws <C>.
 Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
|
- INSTALL NO. 2 SIDE DEFROSTER NOZZLE DUCT
- Engage the claw as shown in the illustration.
 Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
|
 |
Install in this Direction |
- Engage the 2 guides as shown in the illustration.
 Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
|
|
Install in this Direction |
- Install the No. 2 side defroster nozzle duct with the 2 screws <C>.
- INSTALL NO. 1 SIDE DEFROSTER NOZZLE DUCT
- Engage the claw as shown in the illustration.
 Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
|
|
Install in this Direction |
- Engage the 2 guides as shown in the illustration.
 Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
|
|
Install in this Direction |
- Install the No. 1 side defroster nozzle duct with the screw <C>.
- INSTALL INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY
Refer to PROCEDURE - Step 2