Removal [04/2018 -]: Procedure
- PRECAUTION
- w/o Navigation System:NOTE:
- When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly which was installed to another vehicle is used, the following may occur:
- A communication malfunction DTC may be stored.
- The radio and display receiver assembly may not operate normally.
for Gasoline Model: Refer to PRECAUTION [04/2018 - 08/2021] , or refer to PRECAUTION [08/2021 -]
for HV Model: Refer to PRECAUTION [04/2018 - 08/2021] , or refer to PRECAUTION [08/2021 -]
- When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly which was installed to another vehicle is used, the following may occur:
- w/ Navigation System:NOTE:
- When replacing the radio and display receiver assembly or navigation ECU, always replace it with a new one. If a radio and display receiver assembly or navigation ECU which was installed to another vehicle is used, the following may occur:
- A communication malfunction DTC may be stored.
- The radio and display receiver assembly or navigation ECU may not operate normally.
- After replacing the radio and display receiver assembly, if "New software is not compatible with the system. Contact your dealer." is displayed on the multi-display, update the software of the navigation ECU.
for Gasoline Model: Refer to PRECAUTION [04/2018 - 08/2021] , or refer to PRECAUTION [08/2021 -]
for HV Model: Refer to PRECAUTION [04/2018 - 08/2021] , or refer to PRECAUTION [08/2021 -]
- When replacing the radio and display receiver assembly or navigation ECU, always replace it with a new one. If a radio and display receiver assembly or navigation ECU which was installed to another vehicle is used, the following may occur:
- w/o Navigation System:
- REMOVE LOWER INSTRUMENT PANEL FINISH PANEL LH
Refer to PROCEDURE - Step 3 [04/2018 - 08/2020] , or refer to PROCEDURE - Step 3 [08/2020 -]
- REMOVE LOWER INSTRUMENT PANEL FINISH PANEL RH
Refer to PROCEDURE - Step 4 [04/2018 - 08/2020] , or refer to PROCEDURE - Step 4 [08/2020 -]
- REMOVE FRONT CONSOLE UPPER PANEL GARNISH
Refer to PROCEDURE - Step 5 [04/2018 - 08/2020] , or refer to PROCEDURE - Step 5 [08/2020 -]
- REMOVE CONSOLE BOX POCKET SUB-ASSEMBLY
Refer to PROCEDURE - Step 6 [04/2018 - 08/2020] , or refer to PROCEDURE - Step 6 [08/2020 -]
- REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
Refer to PROCEDURE - Step 7 [04/2018 - 08/2020] , or refer to PROCEDURE - Step 7 [08/2020 -]
- REMOVE CENTER NO. 1 INSTRUMENT CLUSTER FINISH PANEL
Refer to PROCEDURE - Step 13 [04/2018 - 08/2021] , or refer to PROCEDURE - Step 13 [08/2021 -]
- REMOVE CENTER NO. 2 INSTRUMENT CLUSTER FINISH PANEL
Refer to PROCEDURE - Step 14 [04/2018 - 08/2021] , or refer to PROCEDURE - Step 14 [08/2021 -]
- REMOVE RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET
- REMOVE INTERIOR ILLUMINATION LIGHT SUB-ASSEMBLY
Refer to PROCEDURE - Step 2
- REMOVE NO. 1 RADIO RECEIVER BRACKET
- REMOVE NO. 2 RADIO RECEIVER BRACKET
- REMOVE NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY
- REMOVE RADIO AND DISPLAY RECEIVER ASSEMBLY