LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2018 >> Camry LE >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 6 (Engine Cooling System (2GR-FKS) - Service Information (Except Hybrid)) >> Radiator >> Installation [06/2017 - ] >> Procedure

Installation [06/2017 - ]: Procedure

WARNING: This page is about a different variant/trim than selected.
  1. INSTALL LOWER RADIATOR SUPPORT 
    1. Install the 2 lower radiator supports to the radiator assembly.
  2. INSTALL RADIATOR SUPPORT CUSHION 
    1. Install the 2 radiator support cushions to the radiator assembly.
  3. INSTALL RADIATOR ASSEMBLY 
    1. Engage the 2 guides.
    2. Engage the 2 claws to install the fan shroud assembly to the radiator assembly.
      NOTE:

      Do not damage the radiator assembly when installing the fan shroud assembly.

    3. Install the radiator assembly with the fan shroud assembly to the vehicle body.
      NOTE:

      Do not apply excessive force to the cooler condenser assembly or pipe when installing the radiator assembly with the fan shroud assembly.

    4. Connect the cooling fan motor connector.
      1. Engage the wire harness clamp.
        GTY742665Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Lock Lever
      2. Connect the cooling fan motor connector and push down the lock lever to engage the claw as shown in the illustration.
        NOTE:
        • When connecting the cooling fan motor connector, make sure that the connecting parts of the cooling fan motor connector are free of dirt, water or other foreign matter.
        • Be sure to securely connect the cooling fan motor connector.
    5. Engage the 2 guides.
    6. Engage the 2 claws to install the cooler condenser assembly to the radiator assembly.
      NOTE:

      Make sure not to damage the cooler condenser assembly when installing the cooler condenser assembly.

  4. CONNECT NO. 2 RADIATOR HOSE 
    1. Connect the No. 2 radiator hose to the radiator assembly and slide the clip to secure it.
  5. CONNECT NO. 1 RADIATOR HOSE 
    1. Connect the No. 1 radiator hose to the radiator assembly and slide the clip to secure it.
    2. Engage the clamp to connect the No. 1 radiator hose to the fan shroud assembly.
  6. CONNECT NO. 5 WATER BY-PASS HOSE 
    1. Connect the No. 5 water by-pass hose to the radiator assembly and slide the clip to secure it.
    2. Engage the 2 clamps to install the hose clamp (B) to the No. 5 water by-pass hose and No. 6 water by-pass hose.
    3. Engage the 4 clamps to connect the No. 5 water by-pass hose and No. 6 water by-pass hose to the hose clamp (A).
  7. INSTALL UPPER RADIATOR SUPPORT SUB-ASSEMBLY 
    1. Install the upper radiator support sub-assembly with the 4 bolts.

      Torque: 12.5 N*m (127 kgf*cm, 9 ft.*lbf) 

    2. Engage the clamp to connect the hood lock control cable assembly to the upper radiator support sub-assembly.
  8. INSTALL NO. 1 RADIATOR AIR GUIDE RH 
    1. Engage the guide and claw.
    2. Install the No. 1 radiator air guide RH with the clip.
  9. INSTALL NO. 1 RADIATOR AIR GUIDE LH 
    1. Engage the guide and claw.
    2. Install the No. 1 radiator air guide LH with the front radiator side air guide plate LH with the clip.
  10. INSTALL UPPER RADIATOR MOUNTING BRACKET 
    1. Install the 2 upper radiator mounting brackets with the 2 bolts and 2 nuts.

      Torque: 12.5 N*m (127 kgf*cm, 9 ft.*lbf) 

    2. Connect the 2 horn connectors.
  11. INSTALL INLET AIR CLEANER ASSEMBLY 

    Refer to PROCEDURE - Step 45 [06/2017 - 10/2020] , or refer to PROCEDURE - Step 45 [10/2020 - ]

  12. INSTALL HOOD LOCK ASSEMBLY 

    Refer to PROCEDURE - Step 7 [03/2017 - 09/2019] , or refer to PROCEDURE - Step 7 [09/2019 - ]

  13. INSTALL FRONT BUMPER REINFORCEMENT 

    Refer to PROCEDURE - Step 3 [06/2017 - 09/2019] , or refer to PROCEDURE - Step 3 [09/2019 - 10/2020] , or refer to PROCEDURE - Step 3 [10/2020 - ]

  14. INSTALL FRONT BUMPER ENERGY ABSORBER 

    Refer to PROCEDURE - Step 4 [06/2017 - 09/2019] , or refer to PROCEDURE - Step 4 [09/2019 - 10/2020] , or refer to PROCEDURE - Step 4 [10/2020 - ]

  15. INSTALL NO. 2 FRONT BUMPER ENERGY ABSORBER 

    Refer to PROCEDURE - Step 5 [06/2017 - 09/2019] , or refer to PROCEDURE - Step 5 [09/2019 - 10/2020] , or refer to PROCEDURE - Step 5 [10/2020 - ]

  16. INSTALL THERMISTOR ASSEMBLY 

    Refer to INSTALLATION [03/2017 - ]

  17. INSTALL HEADLIGHT ASSEMBLY 

    Refer to INSTALLATION [06/2017 - ]

  18. ADD ENGINE COOLANT 

    Refer to PROCEDURE - Step 2

  19. INSPECT FOR COOLANT LEAK 

    Refer to PROCEDURE - Step 1

  20. INSTALL NO. 1 ENGINE UNDER COVER 

    Refer to PROCEDURE - Step 69 [06/2017 - 10/2020] , or refer to PROCEDURE - Step 69 [10/2020 - ]

  21. INSTALL REAR ENGINE UNDER COVER RH 

    Refer to PROCEDURE - Step 67 [06/2017 - 10/2020] , or refer to PROCEDURE - Step 67 [10/2020 - ]

  22. INSTALL REAR ENGINE UNDER COVER LH 

    Refer to PROCEDURE - Step 68 [06/2017 - 10/2020] , or refer to PROCEDURE - Step 68 [10/2020 - ]

  23. INSTALL FRONT WHEEL OPENING EXTENSION PAD LH 

    Refer to PROCEDURE - Step 70 [06/2017 - 10/2020] , or refer to PROCEDURE - Step 70 [10/2020 - ]

  24. INSTALL FRONT WHEEL OPENING EXTENSION PAD RH 

    Refer to PROCEDURE - Step 71 [06/2017 - 10/2020] , or refer to PROCEDURE - Step 71 [10/2020 - ]

scientia non olet · About LEMON Manuals