LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2017 >> Highlander SE, FWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 13 (Engine Mechanical (2GR-FE) (Service Information) (Except Hybrid) (1 Of 2)) >> Engine Unit >> Removal [12/2013 - 11/2016] >> Procedure

Removal [12/2013 - 11/2016]: Procedure

WARNING: This page is about a different car, the 2016 Toyota Highlander, 2015 Toyota Highlander, and 2014 Toyota Highlander. However, it is still accessible from the selected car via links, so may be relevant.
  1. REMOVE GENERATOR ASSEMBLY 

    Refer to PROCEDURE - Step 6

  2. REMOVE INTAKE MANIFOLD 

    Refer to REMOVAL [12/2013 - 11/2016]

  3. REMOVE THROTTLE BODY BRACKET 
    1. Remove the bolt and throttle body bracket from the engine assembly.
      GTY315590Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  4. REMOVE NO. 1 SURGE TANK STAY 
    1. Remove the bolt and No. 1 surge tank stay from the engine assembly.
      GTY299645Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  5. REMOVE IGNITION COIL ASSEMBLY 

    Refer to PROCEDURE - Step 2

  6. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY RH (TWC: Front Catalyst) 

    Refer to PROCEDURE - Step 7

  7. REMOVE EXHAUST MANIFOLD TO HEAD GASKET 

    Refer to PROCEDURE - Step 8

  8. REMOVE NO. 2 ENGINE OIL LEVEL DIPSTICK GUIDE 
    1. Remove the engine oil level dipstick.
      GTY320402Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the bolt and No. 2 engine oil level dipstick guide.
    3. Remove the O-ring from the No. 2 engine oil level dipstick guide.
      GTY322058Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  9. REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR 

    Refer to PROCEDURE - Step 13

  10. REMOVE NO. 2 MANIFOLD STAY 

    Refer to PROCEDURE - Step 14

  11. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY LH (TWC: Front Catalyst) 

    Refer to PROCEDURE - Step 15

  12. REMOVE EXHAUST MANIFOLD TO HEAD GASKET LH 

    Refer to PROCEDURE - Step 17

  13. REMOVE ENGINE MOUNTING BRACKET RH 
    1. Remove the 3 bolts and engine mounting bracket RH.
      GTY308181Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  14. REMOVE REAR ENGINE MOUNTING BRACKET 
    1. Remove the 3 bolts and rear engine mounting bracket.
      GTY428519Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *A for 2WD
      *B for 4WD
  15. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY 
    1. Remove the 5 bolts and V-ribbed belt tensioner assembly.
      GTY146494Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  16. REMOVE NO. 2 TIMING GEAR COVER 
    1. Remove the 2 bolts and No. 2 timing gear cover.
      GTY308087Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  17. REMOVE WATER PUMP PULLEY 
    1. Using SST, hold the water pump pulley.
      GTY441919Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      • SST: 09960-10010 
        1. 09962-01000
        2. 09963-00700
    2. Remove the 4 bolts and water pump pulley.
  18. REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY 
    1. Remove the bolt, No. 2 idler pulley cover plate, No. 2 idler pulley sub-assembly and idler pulley cover plate.
      GTY307914Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  19. REMOVE NO. 1 VACUUM SWITCHING VALVE 
    1. Remove the bolt and No. 1 vacuum switching valve.
      GTY299603Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  20. REMOVE ENGINE OIL PRESSURE SWITCH ASSEMBLY 

    Refer to PROCEDURE - Step 5

  21. REMOVE KNOCK CONTROL SENSOR 

    Refer to PROCEDURE - Step 2

  22. REMOVE KNOCK CONTROL SENSOR WIRE 
    1. Disengage the 3 clamps and remove the knock sensor wire from the engine assembly.
      GTY315593Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  23. REMOVE ENGINE COOLANT TEMPERATURE SENSOR 

    Refer to PROCEDURE - Step 3

scientia non olet · About LEMON Manuals