Reassembly [12/2012 - 10/2015]: Procedure

1. Attach the 6 clamps to install the front seat wire LH.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

2. Connect the 3 connectors.

1. Install the 2 seat adjuster cover caps to the separate type front seat cushion spring assembly LH.

1. Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   Install the front outer seat cushion edge protector LH in the direction indicated by the arrow in the illustration.

HINT: 

Use the same procedure described for the front outer seat cushion edge protector LH.

1. Attach the clip to install the front lower seat cushion shield LH.
2. Attach the hook in the direction indicated by the arrow in the illustration.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

3. Install the screw.

HINT: 

Use the same procedure described for the front lower seat cushion shield LH.

1. Install the front seat inner belt assembly LH with the nut.

   Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf) 

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

2. Attach the 2 clamps.
3. Attach the 2 wire harness clamps and connector clamp.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *1	Wire Harness Clamp
   *2	Connector Clamp

Refer to PROCEDURE - Step 1

Refer to PROCEDURE - Step 1

1. Set the separate type front seat cushion cover in place.
2. Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 21 new hog rings as shown in the illustration.
   NOTE:

   • Be careful not to damage the separate type front seat cushion cover.
   • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.

   HINT: 

   Install the hog rings at the cutouts if they are there.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *1	Hog Ring Pliers	-	-
   *a	Cutout	-	-

1. Attach the 9 hooks to install the separate type front seat cushion cover with pad.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

2. Attach the 3 wire harness clamps and connector clamp to connect the seat cushion heater wire.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *1	Wire Harness Clamp
   *2	Connector Clamp

3. Connect the connector.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Attach the 2 clamps to install the front No. 2 seat wire LH.
2. Connect the 2 connectors.

Refer to PROCEDURE - Step 1

1. Install the seatback felt to the separate type front seatback spring assembly LH.

1. Install the separate type front seatback pad to the separate type front seatback spring assembly LH.

Refer to PROCEDURE - Step 1

1. Set the separate type front seatback cover in place.
2. Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with 8 new hog rings as shown in the illustration.
   NOTE:

   • Be careful not to damage the separate type front seatback cover.
   • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.

   HINT: 

   Install the hog rings at the cutouts if they are there.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *1	Hog Ring Pliers
   *a	Cutout

3. Pass the separate type front seatback cover bracket through the separate type front seatback pad.
4. Install the 2 nuts.

   Torque: 5.5 N*m (56 kgf*cm, 49 in.*lbf) 

5. Close the 2 fasteners.
6. Pull the straps to tighten them and confirm that there is a protrusion visible on each side.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

7. Using hog ring pliers, connect the straps of the separate type front seatback cover to the separate type front seatback frame sub-assembly LH with 3 new hog rings as shown in the illustration.
   NOTE:

   • Be careful not to damage the separate type front seatback cover.
   • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the straps of the separate type front seatback cover.

   HINT: 

   Install the hog rings at the cutouts if they are there.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *1	Hog Ring Pliers
   *a	Cutout

8. Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback frame sub-assembly LH with 5 new hog rings as shown in the illustration.
   NOTE:

   • Be careful not to damage the separate type front seatback cover.
   • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the straps of the separate type front seatback cover.

   HINT: 

   Install the hog rings at the cutouts if they are there.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *1	Hog Ring Pliers
   *a	Cutout

1. Attach the 4 claws to install the 2 front seat headrest supports.

1. Install the separate type front seatback assembly with the 4 bolts.

   Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf) 

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

2. Attach the 2 hooks.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

3. Connect the connector and attach the wire harness clamp.
4. Attach the fastener to connect the wire harness of the front seat airbag assembly LH.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *1

   Fastener

5. Attach the 4 wire harness clamps and connector clamp.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *1	Wire Harness Clamp
   *2	Connector Clamp

6. Connect the connector.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

7. Attach the wire harness clamp and connector clamp.
8. Connect the rubber band.

1. Attach the 3 guides and 2 claws as indicated by the arrows in the order shown in the illustration to install the front inner seat cushion shield LH.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   	First
   	Second

Refer to PROCEDURE - Step 1

Refer to PROCEDURE - Step 1

1. Attach the 2 claws to install the reclining power seat switch knob.

1. Attach the 2 claws to install the slide and vertical power seat switch knob.

1. Connect the 3 connectors and attach the 3 clamps.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

2. Attach the 3 claws to close the cover.
3. Attach the 3 guides and claw as indicated by the arrows in the order shown in the illustration to install the front seat cushion shield LH.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   	First
   	Second

4. Attach the clip.

1. Attach the 2 claws, guide and clip in the direction indicated by the arrow shown in the illustration to install the front inner No. 1 seat cushion shield LH.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

2. Attach the claw and install the screw.