Hood Lock Control Cable Assembly: Installation

INSTALL HOOD LOCK CONTROL CABLE ASSEMBLY

Pass the hood lock control cable assembly into the engine compartment.

Fig 1: Identifying Hood Lock Control Cable Assembly

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

HOOD LOCK CONTROL CABLE PART DESCRIPTION

Area	Part Name	Area	Part Name
A	Hood lock control cable	H	Grommet
B	Clamp	I	Side member outer
C	Wire harness	J	Radiator
D	Pillar	K	Radiator support cover
E	Nut	L	Front fender apron
F	Radiator support upper	M	Brace
G	Hood lock protector	-	-

Pass the cable through the upper radiator support.
Connect the clamps as shown in Fig 1.

INSTALL HOOD LOCK CONTROL LEVER SUB-ASSEMBLY
1. Install the hood lock control lever and connect the hood lock control cable.
  
  Fig 2: Identifying Hood Lock Control Lever
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL HOOD LOCK ASSEMBLY (w/o Engine Hood Courtesy Switch)
1. Apply MP grease to the sliding areas of the lock.
  
  Fig 3: Locating MP Grease Applying Sliding Areas Of Lock
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Connect the hood lock control cable.
  
  Fig 4: Identifying Hood Lock Control Cable
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Install the hood lock assembly with the 3 bolts.
  Torque: 7.5 N*m (77 kgf*cm, 66 in.*lbf)
  
  Fig 5: Identifying Hood Lock Assembly Bolts
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL HOOD LOCK ASSEMBLY (w/ Engine Hood Courtesy Switch)
1. Apply MP grease to the sliding areas of the lock.
  
  Fig 6: Locating MP Grease Applying Sliding Areas Of Lock
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Connect the hood lock control cable.
  
  Fig 7: Identifying Hood Lock Control Cable
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Install the hood lock assembly with the 3 bolts.
  Torque: 7.5 N*m (77 kgf*cm, 66 in.*lbf)
  
  Fig 8: Identifying Hood Lock Assembly Bolts
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
4. Connect the connector.
INSTALL HIGH PITCHED HORN ASSEMBLY (See INSTALLATION )
INSTALL FRONT FENDER LINER
1. Install the front fender liner with the grommet and 4 screws.
2. Install the bolt and 5 clips.
  
  Fig 9: Identifying Front Fender Liner
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSPECT HOOD SUB-ASSEMBLY (See ON-VEHICLE INSPECTION )
ADJUST HOOD SUB-ASSEMBLY (See ADJUSTMENT )
INSTALL FRONT BUMPER ASSEMBLY (w/o Fog Light) (See INSTALLATION )
INSTALL FRONT BUMPER ASSEMBLY (w/ Fog Light) (See INSTALLATION )
INSTALL COOL AIR INTAKE DUCT SEAL (for 2GR-FE) (See INSTALLATION )
INSTALL FRONT WHEEL OPENING EXTENSION PAD
1. Install the front wheel opening extension pad with the 3 screws.
  
  Fig 10: Identifying Front Wheel Opening Extension Pad With Screws
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL FRONT WHEEL (See INSTALLATION )
VEHICLE PREPARATION FOR FOG LIGHT AIM ADJUSTMENT (w/ Fog Light) (See ADJUSTMENT )
PREPARATION FOR FOG LIGHT AIMING (w/ Fog Light) (See ADJUSTMENT )
FOG LIGHT AIMING INSPECTION (w/ Fog Light) (See ADJUSTMENT )
FOG LIGHT AIMING ADJUSTMENT (w/ Fog Light) (See ADJUSTMENT )