Roof Headlining: Installation

WARNING: This page is about a different car, the 2007 Toyota RAV4. However, it is still accessible from the selected car via links, so may be relevant.

INSTALL NO. 1 ROOF SILENCER PAD
1. w/o Sliding Roof:
  1. Install the 5 silencer pads.
2. w/Sliding Roof:
  1. Install the 2 silencer pads.
INSTALL NO. 3 ROOF SILENCER PAD
INSTALL NO. 1 ROOF WIRE
1. Only when replacing the roof headlining:
  1. Align the marking, and then install the wire harness with tape.
    HINT:
    
    Be careful that dirt or foreign objects do not stick to the adhesive part when peeling off the double-sided tape.
  2. Attach the roof wire harness along the adhesive part.
    NOTE: The roof wire harness should be attached securely.
  Fig 1: Installing Roof Wire
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL NO. 1 ROOF HEADLINING SUPPORT
INSTALL NO. 2 ROOF HEADLINING SUPPORT
INSTALL NO. 3 ROOF HEADLINING SUPPORT
INSTALL NO. 4 ROOF HEADLINING SUPPORT
INSTALL ROOF HEADLINING ASSEMBLY
1. w/o Sliding Roof:
  1. Install the headlining with the 4 clips.
2. w/Sliding Roof:
  1. Install the headlining with the 2 clips.
  2. Connect the connector to the sliding roof drive gear.
3. Connect the connector to the roof wire.
  
  Fig 2: Connecting Connector To Roof Wire
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
4. Attach the clamp of the roof wire.
INSTALL SUN ROOF OPENING TRIM MOULDING
INSTALL SHOULDER BELT ANCHOR COVER RH (See INSTALLATION )
INSTALL CHILD RESTRAINT SEAT TETHER ANCHOR COVER (See appropriate step(s) under INSTALLATION )
INSTALL REAR ASSIST GRIP ASSEMBLY
1. Attach the 4 claws to install the assist grip.
INSTALL ASSIST GRIP COVER (for Rear Grip)
1. Attach the 4 claws to install the 2 assist grip covers.
  
  Fig 3: Attaching Claws To Install 2 Assist Grip Covers
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL ASSIST GRIP SUB-ASSEMBLY
1. Attach the 4 claws to install the assist grip.
INSTALL ASSIST GRIP COVER (for Front Grip)
1. Attach the 4 claws to install the 2 assist grip covers.
  
  Fig 4: Attaching Claws To Install 2 Assist Grip Covers
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL TELEVISION DISPLAY ASSEMBLY (w/Television Display) (See appropriate step(s) under INSTALLATION )
INSTALL TELEVISION GARNISH (w/Television Display) (See appropriate step(s) under INSTALLATION )
INSTALL ROOM LIGHT ASSEMBLY (See appropriate step(s) under INSPECTION )
INSTALL MAP LIGHT ASSEMBLY (See appropriate step(s) under REASSEMBLY )
INSTALL VANITY LIGHT ASSEMBLY (See appropriate step(s) under INSTALLATION )
INSTALL VISOR HOLDER
1. Set the claws of the visor holder as shown in the illustration.
2. Insert the visor holder to install it.
  
  Fig 5: Setting Claws Of Visor Holder
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL VISOR ASSEMBLY LH
1. Attach the 2 claws to install the visor.
2. Install portion A of the visor onto the visor holder.
  
  Fig 6: Installing Portion A Of Visor Onto Visor Holder
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Attach the 4 claws to install the visor bracket cover.
INSTALL VISOR ASSEMBLY RH
HINT:

Use the same procedures described for the LH side.
INSTALL REAR ROOM PARTITION NET HOOK LH
1. Install the net hook with the 2 screws.
  
  Fig 7: Installing Net Hook
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL REAR ROOM PARTITION NET HOOK RH
HINT:

Use the same procedures described for the LH side.
INSTALL INNER ROOF SIDE GARNISH ASSEMBLY LH (w/o Rear No. 2 Seat)
1. Attach the 8 clips to install the garnish.
  
  Fig 8: Attaching Clips To Install Garnish
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL INNER ROOF SIDE GARNISH ASSEMBLY LH (w/Rear No. 2 Seat)
1. Attach the 8 clips to install the garnish.
  
  Fig 9: Attaching Clips To Install Garnish
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Connect the rear No. 2 seat belt's shoulder anchor.
  1. Connect the shoulder anchor with the bolt.
    Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf)
    
    Fig 10: Connecting Shoulder Anchor With Bolt
    Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  2. Attach the 2 claws to close the seat belt anchor cover.
INSTALL INNER ROOF SIDE GARNISH ASSEMBLY RH
HINT:

Use the same procedures described for the LH side.
INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH (w/o Rear No. 2 Seat)
1. Install the belt hanger to the trim board.
2. Connect the power outlet socket connector.
3. Attach the 4 clips and 5 claws to install the trim board.
4. Install the 2 screws and 2 bolts.
  
  Fig 11: Attaching Clips And Claws To Install Trim Board
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
5. Connect the rear No. 1 seat belt's floor anchor.
  1. Connect the floor anchor with the bolt.
    Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf)
    
    Fig 12: Connecting Floor Anchor With Bolt
    Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  2. Install the anchor cover.
INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH (w/Rear No. 2 Seat)
1. Install the belt hanger to the trim board.
2. Connect the power outlet socket connector.
3. Attach the 4 clips and 5 claws to install the trim board.
4. Install the 2 screws and 2 bolts.
  
  Fig 13: Attaching Clips And Claws To Install Trim Board
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
5. Connect the rear No. 2 seat belt's floor anchor.
  1. Connect the floor anchor with the bolt.
    Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf)
    
    Fig 14: Connecting Floor Belt Anchor With Bolt
    Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
6. Connect the rear No. 1 seat belt's floor anchor.
  1. Connect the floor anchor with the bolt.
    Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf)
  2. Install the anchor cover.
    
    Fig 15: Connecting Floor Belt Anchor With Bolt
    Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH (w/o Rear No. 2 Seat)
1. Install the belt hanger to the trim board.
2. Attach the 4 clips and 5 claws to install the trim board.
3. Install the 2 screws and 2 bolts.
  
  Fig 16: Attaching Clips And Claws To Install Trim Board
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
4. Connect the rear No. 1 seat belt's floor anchor.
  1. Connect the floor anchor with the bolt.
    Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf)
  2. Install the anchor cover.
    
    Fig 17: Connecting Floor Belt Anchor With Bolt
    Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH (w/Rear No. 2 Seat)
1. Install the belt hanger to the trim board.
2. Attach the 4 clips and 5 claws to install the trim board.
  
  Fig 18: Attaching Clips And Claws To Install Trim Board
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Install the 2 screws and 2 bolts.
4. Connect the rear No. 2 seat belt's floor anchor.
  1. Connect the floor anchor with the bolt.
    Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf)
    
    Fig 19: Connecting Floor Anchor With Bolt
    Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
5. Connect the rear No. 1 seat belt's floor anchor.
  1. Connect the floor anchor with the bolt.
    Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf)
  2. Install the anchor cover.
INSTALL TETHER ANCHOR BRACKET SUBASSEMBLY (w/o Rear No. 2 Seat)
1. Install the tether anchor bracket with the bolt.
  Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf)
  
  Fig 20: Installing Tether Anchor Bracket With Bolt
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL RECLINING REMOTE CONTROL LEVER BEZEL LH (w/o Rear No. 2 Seat) (See appropriate step(s) under INSTALLATION )
INSTALL RECLINING REMOTE CONTROL LEVER BEZEL RH (w/o Rear No. 2 Seat) (See appropriate step(s) under INSTALLATION )
INSTALL REAR DECK TRIM COVER LH (w/Rear No. 2 Seat)
1. Attach the 4 claws to install the trim cover.
2. Install the bolt.
  
  Fig 21: Installing Rear Deck Trim Cover
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL REAR DECK TRIM COVER RH (w/Rear No. 2 Seat)
HINT:

Use the same procedures described for the LH side.
INSTALL REAR FLOOR FINISH PLATE
1. Attach the 6 claws and 6 clips to install the finish plate.
  
  Fig 22: Attaching Claws And Clips To Install Finish Plate
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL BACK DOOR WEATHERSTRIP
INSTALL REAR FLOOR NO. 1 MAT SUPPORT SIDE PLATE
1. w/o Rear No. 2 Seat:
  1. Attach the 7 clips to install the side plate.
  2. Install the 4 screws.
    
    Fig 23: Attaching Clips To Install Side Plate
    Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. w/Rear No. 2 Seat:
  1. Attach the 8 clips to install the side plate.
    
    Fig 24: Attaching Clips To Install Side Plate
    Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL REAR FLOOR NO. 3 BOARD
INSTALL REAR FLOOR NO. 2 BOARD
INSTALL REAR NO. 2 SEAT ASSEMBLY LH (w/Rear No. 2 Seat) (See appropriate step(s) under INSTALLATION )
INSTALL REAR NO. 2 SEAT ASSEMBLY RH (w/Rear No. 2 Seat)
HINT:

Use the same procedures described for the LH side.
INSTALL NO. 2 SEAT LEG COVER LH (w/Rear No. 2 Seat) (See appropriate step(s) under INSTALLATION )
INSTALL NO. 2 SEAT LEG COVER RH (w/Rear No. 2 Seat)
HINT:

Use the same procedures described for the LH side.
INSTALL NO. 2 SEAT HINGE COVER LH (w/Rear No. 2 Seat) (See INSTALLATION )
INSTALL NO. 2 SEAT HINGE COVER RH (w/Rear No. 2 Seat)
HINT:

Use the same procedures described for the LH side.
INSTALL DECK BOARD ASSEMBLY (w/o Rear No. 2 Seat)
INSTALL REAR FLOOR NO. 1 BOARD (w/o Rear No. 2 Seat)
INSTALL TONNEAU COVER ASSEMBLY (w/o Rear No. 2 Seat)
INSTALL PACKAGE TRAY TRIM POCKET SUBASSEMBLY (w/o Rear No. 2 Seat)
INSTALL CENTER PILLAR GARNISH LH
1. Attach the clip to install the garnish.
  
  Fig 25: Attaching Clip To Install Garnish
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Install the 2 screws.
INSTALL CENTER PILLAR GARNISH RH
HINT:

Use the same procedures described for the LH side.
INSTALL LOWER CENTER PILLAR GARNISH LH
1. Attach the 2 claws and 2 clips to install the garnish.
  
  Fig 26: Attaching Claws And Clips To Install Garnish
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Connect the front seat outer belt's floor anchor.
  1. Connect the floor anchor with the bolt.
    Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf)
    
    Fig 27: Connecting Floor Anchor With Bolt
    Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  2. Install the anchor cover.
INSTALL LOWER CENTER PILLAR GARNISH RH
HINT:

Use the same procedures described for the LH side.
INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH
INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH
INSTALL REAR DOOR SCUFF PLATE LH
1. Attach the 9 claws and 2 clips to install the scuff plate.
  
  Fig 28: Attaching Claws And Clips To Install Scuff Plate
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL REAR DOOR SCUFF PLATE RH
HINT:

Use the same procedures described for the LH side.
INSTALL INSTRUMENT PANEL SUB-ASSEMBLY (See REASSEMBLY )
INSTALL FRONT PILLAR GARNISH LH
1. w/Curtain Shield Airbag:
  1. Remove the piece of cloth or nylon.
2. Install the 4 wire harness clamps.
  
  Fig 29: Installing Wire Harness Clamps
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. w/Curtain Shield Airbag:
  1. Install 2 new clips labeled A to the vehicle body.
  2. Set the 3 claws of the pillar garnish to the area labeled B.
  3. Insert the tips of the clips labeled A into the pillar garnish's holes.
  4. Using needle-nose pliers, rotate the tips of clips labeled A 90°. Then push the pillar garnish toward the vehicle body to attach the base of the 2 clips labeled A.
    
    Fig 30: Installing Clips Labeled A To Vehicle Body
    Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
4. w/o Curtain Shield Airbag:
  1. Attach the 2 clips and 3 claws to install the garnish.
    
    Fig 31: Attaching Clips And Claws To Install Garnish
    Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL FRONT PILLAR GARNISH RH
1. w/Curtain Shield Airbag:
  1. Remove the piece of cloth or nylon.
2. w/Curtain Shield Airbag:
  1. Install 2 new clips labeled A to the vehicle body.
    
    Fig 32: Installing Clips Labeled A To Vehicle Body
    Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  2. Set the 3 claws of the pillar garnish to the area labeled B.
  3. Insert the tips of the clips labeled A into the pillar garnish's holes.
  4. Using needle-nose pliers, rotate the tips of clips labeled A 90°. Then push the pillar garnish toward the vehicle body to attach the base of the 2 clips labeled A.
3. w/o Curtain Shield Airbag:
  1. Attach the 2 clips and 3 claws to install the garnish.
    
    Fig 33: Attaching Clips And Claws To Install Garnish
    Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY (See INSTALLATION )
INSTALL INSTRUMENT PANEL REGISTER ASSEMBLY CENTER (See appropriate step(s) under INSTALLATION )
INSTALL RADIO RECEIVER (See appropriate step(s) under INSTALLATION )
INSTALL NO. 2 INSTRUMENT CLUSTER FINISH PANEL CENTER (See appropriate step(s) under INSTALLATION )
INSTALL NO. 1 INSTRUMENT CLUSTER FINISH PANEL CENTER (See appropriate step(s) under INSTALLATION )
INSTALL COMBINATION METER ASSEMBLY (See appropriate step(s) under INSTALLATION )
INSTALL INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (See appropriate step(s) under INSTALLATION )
INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
INSTALL COWL SIDE TRIM BOARD LH
1. Attach the 3 claws to install the trim board.
  
  Fig 34: Attaching Claws To Install Trim Board
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Install the cap nut.
INSTALL COWL SIDE TRIM BOARD RH
HINT:

Use the same procedures described for the LH side.
INSTALL FRONT DOOR SCUFF PLATE LH
1. Attach the 10 claws to install the scuff plate.
  
  Fig 35: Attaching Claws To Install Scuff Plate
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL FRONT DOOR SCUFF PLATE RH
HINT:

Use the same procedures described for the LH side.
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL